Onkyo-DRX2_1-avr-sm 电路图 维修手册.pdf

《Onkyo-DRX2_1-avr-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Onkyo-DRX2_1-avr-sm 电路图 维修手册.pdf（133页珍藏版）》请在收音机爱好者资料库上搜索。

1、Service Manual Published by Onkyo it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely

2、affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. Caution: If Main or Primary fuse enters in the N

3、eutral line of AC Mains supply or if there is possibility of Main or Primary Fuse entering in the Neutral line of AC Mains supply, then AC Mains supply must be disconnected to de-energize the circuit. Ref.No. : 4655 Pre Issue (2017-Apr) Final Issue (2017-Jul) DRX-2.1 AV Receiver Title Page CONTENTS

4、Title Page (This page) Note for Parts List Panel Reset Amp Diag Mode after Abnormal Conditions Wi-Fi 5GHz Setting Model and Destination Firmware Checking Idling Current Hookup and Setting Trouble Shoot Disassembly Schematic Diagram Exploded View Appendix RadioFans.CN 收音机爱 好者资料库 5 4 3 2 1 6 D C A B D

5、 C A B 5 4 3 2 1 6 COMMON D 120V AC G 220230V H 220230240V J 100V AC M 220240V AC P 230V AC U 100240V AC V 110240V W 120V220240V Z 1 Speaker System (without AMP.) : 0 Passive Subwoofer F Front Speaker C Center Speaker R Rear Speaker B Back Speaker A Australia B United Kingdom C North American D USA

6、F Taiwan J Japan K Korea L Russia P Europe Q Hong Kong R China S Brazil T Thai U Worldwide Speaker System (without AMP.) : L Left channel R Right channel 0 Center channel Voltage（電圧記号） Destination（仕向地記号） When parts list is EXCEL file, please refer to the following explanation about file name. P L _

7、T X S R 3 4 3 ( B ) M J J . x l s x Model No. Color (X) Not related to color (B) Black (M) Wood (BR) Brown (O) Orange (C) Cherry (P) Pink (G) Gold (R) Red (GR) Green (S) Silver (H) Gray (V) Violet (K) Black (W) White (L) Blue (Y) Yellow (LB) Light Blue Destination（仕向地記号） Look at the rear panel seria

8、l number 6 digit. J Voltage（電圧記号） Look at the rear panel serial number 5 digit. J Color（色記号） Note for Parts List File Name of Parts List File (EXCEL File) 1 There is a charge function and a power supply (adapter) is needed, but an adapter isnt bundled. （充電機能、電源（）要、付属） RadioFans.CN 收音机爱 好者资料库 5 4 3 2

9、 1 6 D C A B D C A B 5 4 3 2 1 6 DRX-2.1 Panel Front Panel Rear Panel Remote Control Unit Accessory RC-912R 1. Remote controller (RC-912R) (1) 2. Batteries (AAA/R03)(2) 3. Speaker setup microphone (1) 4. Indoor FM antenna (1) 5. AM loop antenna (1) 6. Power cord (1) RadioFans.CN 收音机爱 好者资料库 5 4 3 2 1

10、 6 D C A B D C A B 5 4 3 2 1 6 DRX-2.1 / DRX-3.1 Reset 【STORE】 SETUP + ENTER x 2 【RESET】 1. Volume 40 2. TONE + ON/STANDBY RETURN x 2 3. Unplug the power cord from AVR after the disappeared All Clear of FL tube and AVR goes standby. 【RECALL】 SETUP + RETURN x 2 Detail Key Operation is here Reset Amp

11、Diag Mode after Abnormal Conditions 5 4 3 2 1 6 D C A B D C A B 5 4 3 2 1 6 COMMON Protect Mode The unit goes into standby automatically when detect the abnormal condition of thermal detection, dc voltage detection or current detection. (e.g. TX-NR555 block diagram below) BACLA PCB Info BAAF PCB Inf

12、o BAETC PCB Info BAPS PCB Info BAPRC PCB Info MPU Q7009 VOLTAGE DRIVE RELAY RL6501 (FL/FR) Power amp. (Front L) Q6001 Q6021 SPRLF THERMAL DETECT Q6800 POWER TRANS. T901 CURRENT DETECT Power Supply AC IN PON_MAIN PON_MAIN Relay RL9001 FUSE F9002 SEC-1 (HIGH) SEC-1 (LOW) FUSE F6901 F6902 RELAY RL6911

13、RL6912 Power Supply (H) (L) (H) or (L) SEC1H IPRO DC DETECT VPRO IPROTECT VPROTECT VOLTAGE DETECT VOLH VOLH THERMAL P6800A P9002 P8002 P2800B SUB TRANS. Power Supply for STANDBY VPRO: DC voltage detection IPRO: Current detection SPEAKER - OUT Amp Diag Mode after Abnormal Conditions 5 4 3 2 1 6 D C A

14、 B D C A B 5 4 3 2 1 6 COMMON PCB Information BAPRCBAAFBAETCBAPS TX-NR474BAPRC-2387TX-NR474BAAF-2388TX-NR474BAETC-2390TX-NR474BAPS-2352 TX-NR575ETX-NR575ETX-NR575ETX-NR575EBAPS-2361 TX-8270TX-8270TX-8270TX-8270BAPS-2399 DTM-7DTM-7DTM-7DTM-7BAPS-2399 TX-NR575BAPRC-2409TX-NR575BAAF-1979TX-NR575BAETC-1

15、980TX-NR575BAPS-1984 DRX-2.1DRX-2.1DRX-2.1DRX-2.1BAPS-2000 TX-NR676TX-NR676TX-NR676TX-NR676BAPS-1984 TX-NR676ETX-NR676ETX-NR676ETX-NR676EBAPS-1984 TX-RZ620TX-RZ620TX-RZ620TX-RZ620BAPS-1984 DRX-3.1DRX-3.1DRX-3.1DRX-3.1BAPS-2000 HT-R997HT-R997HT-R997HT-R997BAPS-1984 TX-NR777TX-NR777TX-NR777TX-NR777BAP

16、S-1984 TX-RZ720TX-RZ720TX-RZ720TX-RZ720BAPS-1984 TX-RZ820TX-RZ820TX-RZ820TX-RZ820BAPS-2031 BACLABATRM TX-NR474BACLA-2351TX-NR474BAAF-2388 TX-NR575EBACLA-2360TX-NR575E TX-8270BACLA-2398TX-8270 DTM-7BACLA-2398DTM-7 TX-NR575BACLA-1988TX-NR575BATRM-2023 DRX-2.1BACLA-2004DRX-2.1 TX-NR676BACLA-1988TX-NR67

17、6 TX-NR676EBACLA-1988TX-NR676E TX-RZ620BACLA-1988TX-RZ620 DRX-3.1BACLA-2004DRX-3.1 HT-R997BACLA-1988HT-R997 TX-NR777BACLA-1988TX-NR777 TX-RZ720BACLA-1988TX-RZ720 TX-RZ820BACLA-2030TX-RZ820 Amp Diag Mode after Abnormal Conditions 5 4 3 2 1 6 D C A B D C A B 5 4 3 2 1 6 COMMON Self-diagnostics This fu

18、nction is for avoiding the rupture of electrolytic capacitors with amplifier circuit failure during power-ON. Operation of Self-diagnostic Self-diagnostic will start at the timing of next power on, after goes to the protect mode by Current detection or DC voltage detection. Only On/Standby key could

19、 work in this mode. Also remote control does not work. However, the CLEAR operation is enabled. During Self-diagnostic, the power supply for amplifier circuit become low voltage state(SEC1-LOW), and the speaker relay will be turned off. Then, MPU will check each amplifier circuits Internally by ente

20、ring the test signal (20 kHz,-20 dBFS sine wave) to each channel from DSP. MPU will judge the amplifier circuit is good or not from VOLH value. The normal range of VOLH value is 0.04 V VOLH 0.20 V. If VOLH value is in the out of this range, it will be judged as NG (No good). No problem found When pr

21、otected by current detection, and no problem found, CHECK SP WIRE“ will be displayed. In this State, Only the On/Standby key is effective. And if do not anything for 3 minutes, unit goes into standby automatically. When protected by a DC voltage detection, and no problem found, unit goes into normal

22、 operation. Problem found When judged as there is a problem on any channel, the information of channel that has a problem will be displayed as in the right figure. In this State, Only the On/Standby key is effective. Also remote control does not work. If do not anything for 3 minutes, unit goes into

23、 standby automatically. This state will keep also after unit turn on/off, or AC unplugged. the power supply for amplifier circuit become low voltage state(SEC1-LOW), and the speaker relay will be turned off. Display of during Self-diagnostics A M P D i a g M o d e 2 Line FL tube type “Mode” This par

24、t display the channel which is currently checked. (E.g. FL, etc.) A M P D i a g M o d e 1 Line FL tube type Display of when problem found N G C H : L C R S L S R B L B R N G : L C R S L S R B L B R 2 Line FL tube type 1 Line FL tube type L C R S L S R B L B R Front L channel Center channel Front R c

25、hannel Surround L channel Surround R channel Surround back R channel Surround back L channel Amp Diag Mode after Abnormal Conditions 5 4 3 2 1 6 D C A B D C A B 5 4 3 2 1 6 COMMON Repair Process and How to Confirm Confirmation of the protect cause While NG channel is displayed, You can confirm the p

26、rotect cause by following the step below. 1. Press the Enter button 2. The protect cause are displayed for 5 seconds. Please check the around of those amplifier circuit and repair it. Clear of NG CH information After repair, you can clear NG CH information by following the steps below. 1. Press the

27、On/Standby key while pressing the Enter key. 2. Display as in the right figure appears. 3. Unit goes into Standby automatically after 5 seconds. Self-diagnostic will start again at the timing of next power on. By this, You can verify whether repair was properly or not. If problem found after repair,

28、 please re-check the around of its circuit. Cancel of Self-diagnostic You can cancel this mode by clear operation (press Standby key while pressing CBL/SAT key). After cancel this mode, receiver will be started as normal operation. Manual Execution of Self-diagnostic 1. DIMMER + ON/STANDBY x 2 Main

29、Firmware Version will appear on the main units display. 2. SETUP or HOME Service information will appear on the main units display 3. ENTER Display as in the right figure appears. 4. STANDBY/ON Unit will go into standby. 5. STANDBY/ON Unit will turn on. Then self-diagnostic will start automatically.

30、 Protected by current detection Protected by DC Voltage detection D E T . P R O T E C T : I D E T . P R O T E C T : V N G C H C L E A R Clear of NG CH information A M P D I A G T E S T O N Manual Execution of Self-diagnostic Amp Diag Mode after Abnormal Conditions 5 4 3 2 1 6 D C A B D C A B 5 4 3 2

31、 1 6 COMMON Service information 1/2 CUROR UP CURSOR DOWN CURSOR UP CURSOR DOWN Displaying Service information This service information display system is helpful in analyze the status when the unit goes into Protect mode and is powered off. Pay attention that the status will change if a button is pus

32、hed. How to enter to service information mode. Step1 : DIMMER + ON/STANDBY x 2 Step2 : SETUP or HOME Step3 : SETUP or HOME Note) If press ENTER during service information mode, the following display will appear. And Self-diagnostic will start at when next turn on. How to change History No. 1 3. CURS

33、OR UP or CURSOR DOWN How to exit the service information mode. ON/STANDBY RETURN (to initialize the data in the service information.) Normal display M1.xx / xxxxxAEx The version of main microprocessor. (displayed only for 3 seconds) 1 - 8 0 F 2 7 D D Power off Cause T : Thermal Protect V : Voltage P

34、rotect I : Current Protect - : Other Temperature : xx F or xx C Volume Level Listening Mode Please see the “Listening Mode code list” on the next page. 1 01: 23 10h Information Displayed (Record this Information) Time after Power on xx : xx Cumulative operation time after Reset : xx h Protect Data C

35、LR Normal display History No. : 1 3 (1 is latest.) 1 01: 23 10h 2 01: 47 8h 3 00: 00 00h 1 I 8 0 F 3 0 D D 2 I 9 1 F 2 7 D D 3 - 0 0 F 0 0 A T : 0 I : 2 V : 0 No Use T : Thermal Protect SETUP or HOME History No. : 1 3 (1 is latest.) Count of each protect I : Current Protect V : Voltage Protect Amp D

36、iag Mode after Abnormal Conditions 5 4 3 2 1 6 D C A B D C A B 5 4 3 2 1 6 COMMON Listening Mode Code List Service Information 2/2 00 NORMAL_LMD_BEGIN 01 LAST 02 PURE 03 DIRECT 04 STEREO 05 MONO 06 ORCHESTRA 07 UNPLUGGED 08 STUDIOMIX 09 TVLOGIC 0A ALLCHST 0B FULLMONO 0C TD 0D RPG 0E ACTION 0F ROCKBA

37、ND 10 SPORTS 11 WHOLEHOUSE 12 RPG_GENRE 13 ACTION_GENRE 14 ROCKBAND_GENRE 15 SPORTS_GENRE 12 NORMAL_LMD_END 20 SURR_LMD_BEGIN 21 SURR_20_PLII_MOVIE 22 SURR_20_PLII_MUSIC 23 SURR_20_PLII_GAME 24 SURR_20_PLIIX_MOVIE 25 SURR_20_PLIIX_MUSIC 26 SURR_20_PLIIX_GAME 27 SURR_20_PLIIZ 28 SURR_20_NEO6_MOVIE 29

38、 SURR_20_NEO6_MUSIC 2A SURR_20_NEURAL_MUSIC 2B SURR_20_NEURAL_CINEMA 2C SURR_51_OFF 2D SURR_51_MTR 2E SURR_51_DSC 2F SURR_51_NEO6 30 SURR_51_EX 31 SURR_51_PLIIX_MOVIE 32 SURR_51_PLIIX_MUSIC 33 SURR_51_PLIIZ 34 SURR_51_NEURAL_CINEMA 35 SURR_20_NEOX_CINEMA 36 SURR_20_NEOX_MUSIC 37 SURR_20_NEOX_GAME 38

39、 SURR_51_NEOX_CINEMA 39 SURR_51_NEOX_MUSIC 40 SURR_51_NEOX_GAME 41 SURR_20_DOLBY_SURR 42 SURR_51_DOLBY_SURR 43 SURR_LMD_END 48 DTSSS_LMD_BEGIN 49 DTSSS_20_NEO6_MUSIC 4A DTSSS_20_NEO6_CINEMA 4B DTSSS_51 4C DTSSS_LMD_END 50 THX_MUSIC_LMD_BEGIN 51 THX_20_PLII_MUSIC 52 THX_20_PLIIX_MUSIC 53 THX_20_PLIIZ

40、_MUSIC 54 THX_20_NEO6_MUSIC 55 THX_20_NEURAL_MUSIC 56 THX_51_OFF_MUSIC 57 THX_51_MTR_MUSIC 58 THX_51_DSC_MUSIC 5A THX_51_PLIIX_MUSIC 5B THX_51_PLIIZ_MUSIC 5C THX_51_NEO6_MUSIC 5D THX_51_NEURAL_MUSIC 5E THX_20_NEOX_MUSIC 5F THX_51_NEOX_MUSIC 60 THX_20_DOLBY_SURR_MUSIC 61 THX_51_DOLBY_SURR_MUSIC 62 TH

41、X_MUSIC_LMD_END 70 THX_GAME_LMD_BEGIN 71 THX_20_PLII_GAME 72 THX_20_PLIIX_GAME 73 THX_20_PLIIZ_GAME 74 THX_20_NEURAL_GAMES 75 THX_51_OFF_GAMES 76 THX_51_MTR_GAMES 77 THX_51_DSC_GAMES 78 THX_51_PLIIX_GAME 79 THX_51_PLIIZ_GAMES 7A THX_51_NEO6_GAMES 7B THX_51_NEURAL_GAMES 7C THX_20_NEOX_GAMES 7D THX_51

42、_NEOX_GAMES 7E THX_20_DOLBY_SURR_GAME 7F THX_51_DOLBY_SURR_GAME 80 THX_GAME_LMD_END 90 THX_CINEMA_LMD_BEGIN 91 THX_20_PLII_MOVIE 92 THX_20_PLIIX_MOVIE 93 THX_20_PLIIZ_CINEMA 94 THX_20_NEO6_MOVIE 95 THX_20_NEURAL_CINEMA 96 THX_51_OFF_CINEMA 97 THX_51_MTR_CINEMA 98 THX_51_DSC_CINEMA 99 THX_51_NEO6_CIN

43、EMA 9A THX_51_PLIIX_MOVIE 9B THX_51_PLIIZ_CINEMA 9C THX_51_NEURAL_CINEMA 9D THX_51_EX 9E THX_20_NEOX_CINEMA 9F THX_51_NEOX_CINEMA A0 THX_20_DOLBY_SURR_CINEMA A1 THX_51_DOLBY_SURR_CINEMA A2 THX_CINEMA_LMD_END B0 THX_U2GAME_LMD_BEGIN B1 THX_20_PLII_SLCT2_GAME B2 THX_20_PLIIZ_SLCT2_GAME B3 THX_51_SLCT2

44、_GAM B4 THX_51_PLIIZ_SLCT2_GAME B5 THX_U2GAME_LMD_END B6 THX_U2MUSIC_LMD_BEGIN B7 THX_51_SLCT2_MUS B8 THX_51_PLIIZ_SLCT2_MUSIC B9 THX_U2MUSIC_LMD_END BA THX_U2CINEMA_LMD_BEGIN BB THX_51_SLCT2_CIN BC THX_51_PLIIZ_SLCT2_CINEMA BD THX_U2CINEMA_LMD_END D0 AUDYSSEY_LMD_BEGIN D1 AUDYSSEY_20_PLII_MUSIC D2

45、AUDYSSEY_20_PLIIX_MUSIC D3 AUDYSSEY_20_NEO6_MUSIC D4 AUDYSSEY_20_NEURAL_CINEMA D5 AUDYSSEY_20_NEURAL_MUSIC D6 AUDYSSEY_20_PLII_MOVIE D7 AUDYSSEY_20_PLIIX_MOVIE D8 AUDYSSEY_20_NEO6_MOVIE D9 AUDYSSEY_20_PLII_GAME DA AUDYSSEY_20_PLIIX_GAME DB AUDYSSEY_51_OFF DC AUDYSSEY_51_PLIIX_MUSIC DD AUDYSSEY_51_PL

46、IIX_MOVIE DE AUDYSSEY_51_NEO6 DF AUDYSSEY_51_NEURAL_CINEMA E0 / AUDYSSEY_51_NEURAL_MUSIC E1 AUDYSSEY_51_EX E2 AUDYSSEY_LMD_END F0 SPECIAL_LMD_BEGIN F1 TESTTONE F2 TESTTHR F3 TESTAUTO F4 ASC F5 FLASH F6 DEBUGMODE F7 FLASH2 F8 FLASH3 F9 FLASH4 FA FLASH_CHECK FB SPECIAL_LMD_END WiFi 5GHz Setting 5 4 3

47、2 1 6 D C A B D C A B 5 4 3 2 1 6 DRX-2.1/3.1 DRX-4.1/5.1 Wireless LAN 5GHz Setting IMPORTANT! Back Ground: It is totally different from Radio Law at the each country on 5GHz band. It means it is totally different from enabled Channel of 5GHz band at the each country. We define the “Country Code” for 5GHz band. You must set up the appropriate country code to the product. Example; Case1: When you use the “P”