Onkyo-HTR695-avr-sm 电路图 维修手册.pdf

《Onkyo-HTR695-avr-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Onkyo-HTR695-avr-sm 电路图 维修手册.pdf（167页珍藏版）》请在收音机爱好者资料库上搜索。

1、SAFETY-RELATED COMPONENT WARNING! : COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE MESUREMEN

2、TS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. Published by Onkyo Case1: When you use the “P” destination products and bring move to Russia or Israel, If you did not setup change country code and use in Russia and I

3、srael, You will be on the illegal Radio Law in Russia and Israel. Case2; When you use “C” or “D” destination product bring move to Japan or Taiwan, If you did not setup change country code and use in Japan and Taiwan, You will be on the illegal Radio Law in Japan and Taiwan. Service Parts informatio

4、n: The default country code is set on “Processing Circuit Board(PRC board)”. You must make sure and set up the “Country Code“ when you replace the processing circuit pc board. Otherwise You and your customer should be on the illegal Radio Law and IT HAS POSSIBILITY TO HAVE A RISK OF PUNISHMENT FROM

5、EACH COUNTRY GOVERNMENT. If you did not make sure country code and no setup code and face any trouble, We does not have any responsibility. For setting up the Country Code, Please ask the procedure of changing country code to your distributer or our sales. It is no described the procedure of changin

6、g Country Code on this Service Manual If you have any trouble of unclear procedure for update country code, Please contact our sales department. PRC Board Default Value of Country Code The PRC board is already set default Country Code by the representative destination. To confirm the default country

7、 code, Please refer to the How to read PRC Board part number and Default value of Country Code section. Figure Country List (need to set up) WiFi 5GHz Setting 5 4 3 2 1 6 D C A B D C A B 543216 TX-NR555/656/757/HT-R695 TX-RZ610/710/810 Wireless LAN 5GHz Setting IMPOTANT! Make sure and Setup Country

8、Code You have to make sure country code for using or replacing “Processing Circuit PC Board”. It means that you have to make sure country code between using Processing Circuit PC board( PRC Board) and your customers country code. When it is not matchPRC board default country code and customers count

9、ry, you have to setup Country Code. Case3; When you repair the “P” destination products and replace “P” destination PRC Board and the customer live in UK, It is no necessary to setup Country Code Because “P” destination PRC board already setup “EU” country code. Match Country code NO NECESSARY TO SE

10、TUP COUNTRY CODE Case4; When you repair the “P” destination products and replace “P” destination PRC board and the customer live in Russia, It is necessary to setup Country Code Because “P” destination PRC Board already setup “EU” country code. However, the customers country code is “RU”. It means n

11、o match PRC Board code and Customers code. No Match Country code NECESSARY TO SETUP COUNTRY CODE Case5; When you repair the “C” destination products and replace “C” destination PRC board and the customer live in US, it is no necessary to setup Country Code Because “C” destination PRC board already s

12、etup “US” country code. Match Country code NO NECESSARY TO SETUP COUNTRY CODE Case6; When you repair the “C” destination product and replace “C” destination PRC board and the customer live in Taiwan, It is necessary to setup Country Code. Because “C” destination PRC Board already setup “US” country

13、code as default. However, the customers country code is “TW”. It means no match PRC Board code and the customers country code No Match Country code NECESSARY TO SETUP COUNTRY CODE Customer: UK: EUPRC Board: EU Customer: Russia: RUPRC Board: EU Customer: US: USPRC Board: US Customer: Taiwan: TWPRC Bo

14、ard: US WiFi 5GHz Setting 5 4 3 2 1 6 D C A B D C A B 543216 TX-NR555/656/757/HT-R695 TX-RZ610/710/810 Wireless LAN 5GHz Country Code 1/2 RegionCountryCode America USAUS CanadaUS MexicoUS BrazilUS ChileCL GuatemalaUS Puerto RicoUS TrinidadTT Dominican RepUS ArgentinaAR EcuadorUS ParaguayPY ColombiaU

15、S GuamUS PanamaUS Costa RicaUS UruguayUY PeruPE RegionCountryCode Asia / Oceania JapanJP ChinaCN Hong KongEU KoreaKR TaiwanTW SingaporeSG MalaysiaMY PhilippinesEU VietnamEU IndonesiaID Sri LankaEU AustraliaAU New Zealand AU ThailandEU IndiaIN PakistanPK RegionCountryCode Middle East UAEEU BahrainBH

16、KuwaitKW OmanEU QatarQA LebanonEU JordanJO Saudi ArabiaEU WiFi 5GHz Setting 5 4 3 2 1 6 D C A B D C A B 543216 TX-NR555/656/757/HT-R695 TX-RZ610/710/810 Wireless LAN 5GHz Country Code 2/2 RegionCountryCode Europe / Africa GermanyEU UKEU FranceEU NetherlandsEU ItalyEU SwitzerlandEU DenmarkEU SwedenEU

17、 AustriaEU BelgiumEU SpainEU NorwayEU FinlandEU CzechEU IsraelIL UkraineEU HungaryEU SlovakiaEU LuxembourgEU TurkeyEU PortugalEU MaltaEU LatviaEU PolandEU RegionCountryCode Europe / Africa CyprusEU EstoniaEU SloveniaEU BulgariaEU GreeceEU RomaniaEU LithuaniaEU SerbiaEU CroatiaEU IrelandEU MacedoniaE

18、U MoldovaEU RussiaRU AndorraEU ArmeniaEU AzerbaijanEU BelarusEU Bosnia and Herzegovina EU Northern Cyprus(Turkey) EU GeorgiaEU IcelandEU KazakhstanEU RegionCountryCode Europe / Africa LiechtensteinEU MonacoEU MontenegroEU San MarinoEU Vatican CityEU KosovoEU Kaliningrad(Russia)RU Gibraltar(UK)EU Can

19、ary Islands(Spain) EU CeutaEU MelillaEU MoroccoMA AlgeriaEU TunisiaTN EgyptEG MauritiusUS South AfricaEU WiFi 5GHz Setting 5 4 3 2 1 6 D C A B D C A B 543216 TX-NR555/656/757/HT-R695 TX-RZ610/710/810 How to read PRC Board part number and Default value of Country Code 1B5142034-1A555MDC Board No. 555

20、 : TX-NR555 656 : TX-NR656 757 : TX-NR757 695 : HT-R695 610 : TX-RZ610 710 : TX-RZ710 810 : TX-RZ810 PRC Board Default setting Country Code Dst Code Main Country C US North America D US United State S US Brazil P EU Europe B EU United Kingdom Q EU Hong Kong T EU Thai L RU Russia A AU Australia / New

21、 Zealand R CN China F TW Taiwan K KR Korea J JP Japan Model Number Last 3 Digit Destination Suffix No. Code US US US EU EU EU EU RU AU CN TW KR JP Firmware 5 4 3 2 1 6 D C A B D C A B 543216 How to check Firmware Version & Preparation of Update HT-R695 Step1 : DIMMER + ON/STANDBY x 2 Main Firmware V

22、ersion will appear on the main units display. Step2 : TONE +1 ( Rotate “TONE” knob right 1 click) NET Firmware Version will appear on the main units display. Step3 : TONE +2 ( Rotate “TONE” knob right 2 click) DSP Firmware Version will appear on the main units display. Step4 : TONE +3 ( Rotate “TONE

23、” knob right 3 click) Video Firmware Version will appear on the main units display. Step3 : TONE +4 ( Rotate “TONE” knob right 4 click) OSD Firmware Version will appear on the main units display. Step4 : TONE +5 over ( Rotate “TONE” knob right 5 click over) Return to Display Main Firmware Version (

24、Return Step1) When It is rotated left ( - ) TONE knob, It is appeared before step. Preparation of Update 1.Connect the USB storage device to your PC. If there is any data in the USB storage device, remove it. 2.Download the firmware file (package file) from the Onkyo FTP-server. However European ser

25、vice partners should download the firmware file (package file) from the ExtraNet. Onkyo FTP-server: ftp:/manex.onkyo.co.jp/ ID and Password are those we informed when changed. Filename is as follows: ONKAVR0001*.zip Unzip the downloaded file. A following file is created. ONKAVR0001*.of0 ONKAVR0001*.

26、of1 ONKAVR0001*.of2 ONKAVR0001*.of3 ONKAVR0001*.of4 3.Copy it to the USB storage device. Be careful not to copy the zip file. 4.Remove the USB storage device from your PC. Firmware 5 4 3 2 1 6 D C A B D C A B 543216 How to Update (service mode) 1/2 HT-R695 Overwriting is also possible. 1.Connect the

27、 USB strage to the USB port on the unit. 2.Turn on the unit. It takes some time to start after you switch on the unit. Press: DIMMER + ON/STANDBY x 2 3. Press RETURN button, Then it is displayed as below If you need each module of the firmware update, you can select the module by pressing PRESET but

28、ton. If you need change source NET or USB, you can select the source by pressing TUNING UP and Down key It should be updated firmware by selecting USB - ALL normally. Please Do NOT choose T-SRV (it is test server) USB - ALL: ALL firmware update ( default ) USB - DSP1: DSP firmware update USB - OSD:

29、OSD firmware update USB - VMPU: VMPU firmware update USB - NET: NET firmware update USB - MMPU: Main MPU firmware update USB - WORK: Compare between AVR and USB, Only update new version firmware NET - ALL: ALL firmware update ( default ) NET - DSP1: DSP firmware update NET - OSD: OSD firmware update

30、 NET - VMPU: VMPU firmware update NET - NET: NET firmware update NET - MMPU: Main MPU firmware update NET - WORK: Compare between AVR and MMC, Only update new version firmware by network The default setting is “ ALL” CAUTION: When you will update each module firmware, you have to keep combination of

31、 firmware. Firmware 5 4 3 2 1 6 D C A B D C A B 543216 How to Update (service mode) 2/2 4. Press ENTER button. Start update firmware. 5.Wait until update is completed. When the update ends, “Completed!” is displayed. When “ Completed!” message appeared, you can power off by pressing “ ON/STANDBY” bu

32、tton. (If you leave it, it automatically turns standby mode. ) 6.Press ON/STANDBY button, and the unit turns on. 7.Check the new FW version number. If the procedure might not be successful, please select “USB - ALL”. HT-R695 Adjustment 5 4 3 2 1 6 D C A B D C A B 543216 TX-NR555/TX-NR656/TX-RZ610/HT

33、-R695 TX-NR757/TX-RZ710/TX-RZ810 DRX-2/DRX-3/DRX-4/DRX-5 How to Adjust Idling ChanelMeasurement PointsPermissible Range FLP6021 1mV 21mV FRP6022 CP6023 SLP6025 SRP6026 SBLP6027 SBRP6028 C P6023 SR P6026 SBR P6028 FR P6022 FL P6021 SBL P6027 SL P6025 The Idling current adjustment is unnecessary. If d

34、id the repair of amplifier circuit, please confirm the idling current after 4 6 minutes heat running. If the measured value are under 1mV or over 21mV , turn off the power of the AVR and check the parts of defect channel again. Connection DC Volt meter AVR 100ohms, 1/4W *Heat sink is different by ea

35、ch model. Hookup and Setting 5 4 3 2 1 6 D C A B D C A B 543216 COMMON No Sound No sound from connected player Chose input selector which is assigned to connected input terminal ? No sound from connected TV Chose wrong input selector ? etc. ? No sound from some connected loudspeaker(s) No sound loud

36、speaker(s) config No sound from all connected TV or Blu-ray player etc. After After 10 seconds, connect power cord again Reset this model 5 4 3 2 1 6 D C A B D C A B 543216 Trouble Shoot TX-NR555/656/757 TX-RZ610/710, HT-R695 Here the trouble shoot which focuses on the hardware troubles regarding PC

37、B assembly is explained. Of course, with actual repair there are also troubles due to damaged Power Transformer, Wiring, soldering etc. in addition to PCB assembly. No Sound (HDMI in) ProcessCheck PointDamaged PCB 1 J6504(BATRM-2023) +24V BAAF-1979 2 P8002A(BADG-1985) BAAF-1979 3 P2802B(BAPRC-2034)

38、BATRM-2023 4 P8003A(BADG-1985) BAPRC-2034 5 P8002A(BADG-1985) BAPRC-2034 6 Q1501(BADG-1985) BADG-1985 7 J4606(BAAF-1979)BAAF-1979 8 Q6001, Q6021(BAAF-1979) Base BACLA-1988 9 P2800B(BAPRC-2034) BAAF-1979 10 P6021(BAAF-1979) The amplified beautiful wave. BAAF-1979 11BATRM-2023 No Good OK No Good OK No

39、 Good OK No Good OK No Good OK No Good OK No Good OK No Good OK No Good OK No Good OK 5 -15V7 +15V 1 +12V +15V 28 +3.3V 29 Signal30 Signal 1 Signal 10 +3V (HIGH) BADG-1985BAPRC-2034 BATRM-2023 BAAF-1979 5 4 3 2 1 6 D C A B D C A B 543216 Trouble Shoot TX-NR555/656/757 TX-RZ610/710, HT-R695 Here the

40、trouble shoot which focuses on the hardware troubles regarding PCB assembly is explained. Of course, with actual repair there are also troubles due to damaged Power Transformer, Wiring, soldering etc. in addition to PCB assembly. No Sound (Opt in) ProcessCheck PointDamaged PCB 1 J6504(BATRM-2023) +2

41、4V BAAF-1979 2 P8002A(BADG-1985) BAAF-1979 3 P2802B(BAPRC-2034) BATRM-2023 4 P8003A(BADG-1985) BAPRC-2034 5 P8003A(BADG-1985) BADG-1985 6 P8002A(BADG-1985) BAPRC-2034 7 Q1501(BADG-1985) BADG-1985 8J4606(BAAF-1979)BAAF-1979 9 Q6001, Q6021(BAAF-1979) Base BACLA-1988 10 P2800B(BAPRC-2034) BAAF-1979 11

42、P6021(BAAF-1979) The amplified beautiful wave. BAAF-1979 12BATRM-2023 No Good OK No Good OK No Good OK No Good OK No Good OK No Good OK No Good OK No Good OK No Good OK No Good OK 5 -15V7 +15V 1 +12V +15V 28 +3.3V 25Signal 29 Signal30 Signal 1 Signal 10 +3V (HIGH) BADG-1985BAPRC-2034 BATRM-2023 BAAF

43、-1979 5 4 3 2 1 6 D C A B D C A B 543216 Trouble Shoot TX-NR555/656/757 TX-RZ610/710, HT-R695 Here the trouble shoot which focuses on the hardware troubles regarding PCB assembly is explained. Of course, with actual repair there are also troubles due to damaged Power Transformer, Wiring, soldering e

44、tc. in addition to PCB assembly. No Sound (Analog in) ProcessCheck PointDamaged PCB 1 J6504(BATRM-2023) +24V BAAF-1979 2 P8002A(BADG-1985) BAAF-1979 3 J4606(BAAF-1979)BAAF-1979 4 Q6001, Q6021(BAAF-1979) Base BACLA-1988 5 P2800B(BAPRC-2034) BAAF-1979 6 P6021(BAAF-1979) The amplified beautiful wave. B

45、AAF-1979 7 BATRM-2023 No Good OK No Good OK No Good OK No Good OK No Good OK No Good OK 5 -15V7 +15V 10 +3V (HIGH) BADG-1985BAPRC-2034 BATRM-2023 BAAF-1979 5 4 3 2 1 6 D C A B D C A B 543216 Trouble Shoot TX-NR555/656/757 TX-RZ610/710, HT-R695 Here the trouble shoot which focuses on the hardware tro

46、ubles regarding PCB assembly is explained. Of course, with actual repair there are also troubles due to damaged Power Transformer, Wiring, soldering etc. in addition to PCB assembly. No Picture (HDMI in/ out) ProcessCheck PointDamaged PCB 1 P2802B(BAPRC-2034) BATRM-2023 2BAPRC-2034 No Good OK 1 +12V

47、 +15V BAPRC-2034 BATRM-2023 5 4 3 2 1 6 D C A B D C A B 543216 Trouble Shoot TX-NR555/656/757 TX-RZ610/710, HT-R695 Here the trouble shoot which focuses on the hardware troubles regarding PCB assembly is explained. Of course, with actual repair there are also troubles due to damaged Power Transformer, Wiring, soldering etc. in addition to PCB assembly. No Picture (Component in/ HDMI out) Process