Onkyo-TXSR8360-avr-sm 电路图 维修手册.pdf

《Onkyo-TXSR8360-avr-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Onkyo-TXSR8360-avr-sm 电路图 维修手册.pdf（144页珍藏版）》请在收音机爱好者资料库上搜索。

1、TX-SR603/603E/8360 SERVICE MANUALSERVICE MANUAL Ref. No. 3864 042005 AV RECEIVER MODEL TX-SR603 MODEL TX-SR603E MODEL TX-SR8360 TX-SR603 Black, Golden and Silver models 120V AC, 60Hz 230-240V AC, 50Hz 120V/220-230V AC, 50/60Hz 220-230V AC, 50/60Hz B MDD, B MDC, S MDC B MPA, S MPA B MWT, G MWT G MGR,

2、 G MGQ, G MGK TX-SR603E Black and Silver models 230-240V AC, 50HzB MPP, S MPP TX-SR8360 Golden model 220-230V AC, 50/60HzG MGR RC-591M STANDBY/ON ZONE2 ZONE 2 LEVEL PHONES PURE AUDIOMULTl CH TONE+STEREOLISTENING MODEDISPLAYDIGITAL INPUTRT/PTY/TPMEMORYTUNING MODE RETURN TUNING/ PRESET ENTER SETUP DVD

3、VIDEO 1VIDEO 2 VCR 1VCR 2 VIDEO 3VIDEO 4TAPETUNERCD SETUP MICS VIDEOVIDEO MASTER VOLUME VIDEO 4 INPUT LRAUDIODIGITAL OFF STANDBY CLEAR SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPL

4、ACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. RadioFans.CN 收音机爱 好者资料库 TX-SR603/6

5、03E/8360 SPECIFICATIONS Audio Outputs Digital Outputs 1(Optical ) 0(Coaxial ) Analog Outputs TAPE, VIDEO1, VIDEO2 Subwoofer Pre Outputs 1 Speaker Outputs 9 Phones 1 Other Jacks IR Input 1 12V Trigger Out 1 Specifications and features are subject to change without notice. Power Supply North American:

6、 AC 120 V, 60 Hz Australian and European: AC 230-240 V, 50 Hz Others: AC 120/220-230 V, 50/60 Hz AC 230-240 V, 50Hz AC 220-230 V, 50/60 Hz Power Consumption North American: 6.7A Others: 650 W Stand-by Power Consumption 1.0 W Dimensions (W x H x D) 435 W x 175 H x 430 D mm 17-1/8 W x 6-7/8 H x 16-15/

7、16 D inches Weight North American, Australian, European, Singapore and East southern asian: 13.6 kg 30.0 lbs Others: 14.8 kg 32.6 lbs Video Outputs Component Video Output OUT S-Video Compatible Jack Output MONITOR OUT, VIDEO1, VIDEO2 A/V Output MONITOR OUT, VIDEO1, VIDEO2 Audio Inputs Digital Inputs

8、 Optical: 4(North American)/ 3(other) Coaxial: 2 Analog Inputs DVD(MULTICHANNEL), VIDEO1, VIDEO2, VIDEO3, VIDEO4, TAPE, CD Multichannel Inputs 6 General Power Output 2 channel driven: North American: 85 W + 85 W (8 , 20Hz-20kHz, FTC) European: 120 W + 120 W (6 , 1kHz, DIN) Asian, Australian: 150 W +

9、 150 W (6 , 1kHz, JEITA) Dynamic Power 220 W + 220 W (3 , Front) 165 W + 165 W (4 , Front) 100 W + 100 W (8 , Front) THD (Total Harmonic Distortion) 0.08 % (Power Rated) Damping Factor 60 (Front, 1kHz, 8 ) Input Sensitivity and Impedance 200 mV/ 47 k (LINE) Output Level and Impedance 200 mV/ 470 (RE

10、C OUT) Frequency Response 10 Hz-100 kHz/ +1 dB-3 dB (Direct mode) Tone Control 10 dB, 50 Hz (BASS) 10 dB, 10 kHz (TREBLE) SN Ratio 106 dB (LINE IHF-A) Speaker Impedance North American: 6 - Others: 4 - Amplifier Section Input Sensitivity/Output Level and Impedance 1 Vp-p /75 (Component and S-Video Y)

11、 0.7 Vp-p /75 (Component Pb/Cb,Pr/Cr) 0.28 Vp-p /75 (S-Video C) 1 Vp-p /75 (Composite) Component Video Frequency Response 5 Hz-50 MHz Video Section FM Tuning Frequency Range North American: 87.5 MHz-107.9 MHz Others: 87.5 MHz- 108.0 MHz Usable Sensitivity Stereo: 17.2 dBf 2 V(75 IHF) Mono: 11.2 dBf

12、1 V(75 IHF) S/N Ratio Stereo: 70 dB (IHF-A) Mono: 76 dB (IHF-A) THD Stereo: 0.3 % (1kHz) Mono: 0.2 % (1kHz) Frequency Response 30 Hz-15 kHz / 1 dB Stereo Separation 45 dB (1kHz) AM Tuning Frequency Range North American: 530 kHz-1700 kHz Others: 522 kHz-1611 kHz Usable Sensitivity 30 V S/N Ratio 40 d

13、B THD 0.70% Tuner Section Video Inputs Component Video Input 1, 2, 3 S-Video Compatible Jack Input DVD, VIDEO1, VIDEO2, VIDEO3, VIDEO4 A/V Input DVD, VIDEO1, VIDEO2, VIDEO3, VIDEO4 RadioFans.CN 收音机爱 好者资料库 TX-SR603/603E/8360 SERVICE PROCEDURE 1. Replacing the fuses This symbol located near the fuse i

14、ndicates that the fuse used is show operating type, For continued protection against fire hazard, replace with same type fuse, For fuse rating, refer to the marking adjacent to the symbol. Ce symbole indique que le fusible utilise est e lent. Pour une protection permanente, nutiliser que des fusible

15、s de meme type. Ce demier est indique la qu le present symbol est apposre. 2. To initialize the unit The AV receiver uses a battery-less memory backup system in order to retain radio presets and other settings when its unplugged or in the case of a power failure. Although no batteries are required,

16、the AV receiver must be plugged into an AC outlet in order to charge the backup system. Once it has been charged, the AV receiver will retain the settings for several weeks, although this depends on the environment and will be shorter in humid climates. 1. Press and the hold down the VIDEO 1/VCR but

17、ton, then press the STANDBY/ON button when the unit is Power on. 2. After Clear is displayed, the preset memory and each mode stored in the memory, are initialized and will return to the factory settings. 4. Memory Backup Main microprocessor Q701 only. 1. Press and the hold down the DISPLAY button ,

18、 then press the STANDBY/ON button when the unit is Power on. Version is displayed on FL display only for 3 seconds. 2. Press the STANDBY/ON button to Power off. 3. To check version of microprocessor Ver.1.01/05305a Ex. REF NO. F901 F901 F901 or F901 or F902 F902 or F902 or F903 F903 or F903 F903 or

19、F903 or F6901 F6901 or F6902 F6902 or F9501 F9501 or F9501 or PART NAME FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE FUSE DESCRIPTION 10A-UL 5A-SE-EAK 5A-SE-TL250V 5A-SE-TL250V 5A-SE-EAK 5A-SE-TL250V 5A-SE-TL250V 5A-UL/T-237 5A-T/UL-ST2 2.5A-SE-EAK 2.5A-S

20、E-TL250V 2.5A-SE-TL250V 12A-UL/T-314 12A-TUL-250V 12A-UL/T-314 12A-TUL-250V 2.5A-SE-EAK 2.5A-SE-TL250V 2.5A-T/UL-ST2 PART NO. 252199 252078 252244 252278 252078 252244 252278 252164 252258 252075 252241 252275 252196 252301 252196 252301 252075 252241 252254 REMARKS !, !, !, !, !, , !, , !, !, !, !,

21、 , !, , !, , ! ! ! ! ! ! ! : TX-SR603 Canadian model : TX-SR603 American model : TX-SR603 Korean model : TX-SR603 Hong kong model : TX-SR603 Chinese model : TX-SR603 Australian model : TX-SR603 World wide model : TX-SR603E European model : TX-SR8360 Chinese model RadioFans.CN 收音机爱 好者资料库 OPERATION CH

22、ECK-1 SPEAKER PROTECT-1 (DC VOLTAGE DETECTION) TX-SR603/603E/8360 1. Press and the hold down the CD button , then press the STANDBY/ON button when the unit is Power ON. Test - _ is displays it only for 5 seconds. 2. Press the VIDEO 3 button, while the character of Test - _ is displayed. Unit will be

23、 in the state of Test-4-00 . 3. Repeatedly press TONE+ button until the character of Test-4-21 is displayed. Procedure No load. No input. Test - _ Test - 4-00 When 1. Exchange power transistors (Q6050 - Q6066). 2. Exchange amplifier PC board assy (NAAF-8523). Test - 4-21 Checking the operation start

24、s automatically as follows. Test - 4-21 Test - 4-22 Test - 4-25 Test - 4-23 Test - 4-24 Protect OK Protect OK Protect Protect OK Protect OK Protect OK Test - 4-35 Clear Turn off Front L ch Check If all channel are OK, the character of Test - 4 - 35 is displayed. 4. Press the STANDBY/ON button. Front

25、 R ch Check Center ch Check Surround L ch Check Surround R ch Check Blinks Test - 4-26 Protect OK Surround Back L ch Check Test - 4-27 Protect OK Surround Back R ch Check TX-SR603/603E/8360 OPERATION CHECK-2 SPEAKER PROTECT-2 (CURRENT DETECTION) 1. Press and the hold down the CD button , then press

26、the STANDBY/ON button when the unit is Power ON. Test - _ is displays it only for 5 seconds. 2. Press the VIDEO 3 button, while the character of Test - _ is displayed. Unit will be in the state of Test-4-00 . 3. Repeatedly press TONE+ button until the character of Test-4-35 is displayed. 4. Connect

27、the Dummy load of 3 ohms to the Front Lch speakers terminal. At this time, check the speaker relay is not turned off. 5. Connect the dummy load of 1 ohm to the Front Lch speakers terminal. At that time, you check the speaker relay is turned off and Protect is displayed. Disconnect the dummy load at

28、once when check the display of Protect . 6. Check other channels according to the same procedure. Procedure No input. Do not check two or more channels at the same time. Do not connect dummy load to speaker terminals fro seconds 2 or more. Test - _ Test - 4-00 When 1. Exchange power transistors (Q60

29、50 - Q6066). 2. Exchange amplifier PC board assy (NAAF-8523). Test - 4-35 Clear Turn off 7. Press the STANDBY/ON button. Test - 4-35 Protect Test - 4-35 Blinks OPERATION CHECK-3 CONTROL OF POWER SUPPLY (OUTPUT SENSOR AND THERMAL SENSOR) TX-SR603/603E/8360 Test - _ Test - 4-00 Test - 4-37 Clear Turn

30、off Test - 4-37 FM STEREO Blinks Ver. 0.50/05131a T: 25 C/ 77 F Clear Turn off Output sensor 1. Press and the hold down the CD button , then press the STANDBY/ON button when the unit is Power ON. Test - _ is displays it only for 5 seconds. 2. Press the VIDEO 3 button, while the character of Test - _

31、 is displayed. Unit will be in the state of Test-4-00 . 3. Repeatedly press TONE+ button until the character of Test-4-37 is displayed. 4. Adjusts MASTER VOLUME to Max. position. At this time, check the character of FM STEREO displayed. And, check relay RL6901 and RL6902 are turned off in 2 - 3 seco

32、nds. 5. Press the STANDBY/ON button. Procedure No output. No input. When 1. Exchange power transistors (Q6050 - Q6066). 2. Exchange power amplifier PC board assy (NAAF-8523). 3. Exchange thermal sensor PC board assy (NAETC-8526). Thermal sensor 1. Press and hold down the DISPLAY button, then press t

33、he STANDBY button when the unit is power ON. Ver. 0.50/05131a is displays it only for 2 seconds. 2. Press the TONE button, while the character of Ver.0.50/05131a is displayed. 3. Check the displayed temperature is +/-20 C of the ambient temperatures. 4. Press STANDBY/ON button. TX-SR603/603E/8360 OP

34、ERATION CHECK-4 DSP DEBUG MODE E1A48K015FF 23o Ver. 0.50/05131a 14256871039 Check the operation of the circuit around DSP by the display in this mode. This information helps to pursue the faulty point. UNLOCK E = UNLOCK = LOCK 1 Digital Selecter D = DIGITAL A = ANALOG 1 = COAX1 2 = OOAX2 3 = OPT1 4

35、= OPT2 5 = OPT3 7 = FRONT 2 Sampling Frequency 96 = 96kHz 48 = 48kHz 44 = 44kHz 32 = 32kHz - = Not detect 3 AUTOBOOT DSP AB CODE 0 = FLASH 1 = ab_ac3_pl2 2 = ab_dts_pl2 3 = ab_neo6 4 = sgen_ab 5 = ab_pl2fs 6 = ab_dts_6dol 7 = ab_dts9624 8 = aac_pl2 6 Pre Emphasis K = OFF e = ON 4 DSP Detect Format 0

36、0 = Null 01 = Dolby Digital 03 = Pause 04 = MPEG1 L1 05 = MPEG1 L23/ MPEG2 w/o 06 = MPEG2 w/e 07 = MPEG2 AAC 08 = MPEG2 L1 09 = MPEG2 L2/3 9 DSP Decode o = Decode OK x = Decode NG - = Analog in 10 To set in DSP debug mode 1. Press and hold down the DISPLAY button, then press the STANDBY button when

37、the unit is power ON. Ver. 0.50/05131a is displays it only for 2 seconds. 2. Press the DISPLAY button, while the character of Ver.0.50/05131a is displayed. To exit Press STANDBY/ON button. - DIR - MEMORY/DOWNLOAD - DIR Status 0 = ANALOG 1 = PCM 2 = NOT_PCM 3 = DATA 4 = DTSCD 5 = MCH 6 = NOT DECIED 5

38、 - DSP - Content of display AUTOBOOT DSP C CODE 0 = ac_dts9624 1 = c_neo6 2 = c_oos_no_sd 3 = c_oos 4 = c_oob 5 = c_pl2 6 = c_pl2xthx 7 = c_thx 8 = c_spsetup 9 = version 7 DSP Status 00 = Power off 01 = Power on wait 10 = DSP reset 11 = DSP reset wait 12 = DSP AB boot ready 13 = DSP AB boot start 14

39、 = DSP AB boot 15 = DSP C boot ready 16 = DSP C boot start 17 = DSP C boot 18 = DSP soft reset 20 = DSP C app start 8 21 = DSP C HW Config set 22 - 2A = DSP C SW Config set 3F = DSP C kick start 40 = DSP AB App start 41 = DSP AB HW Config set 42 - 4B = DSP AB SW Config set AF = DSP ab kick start 0B

40、= DTS1 0C = DTS2 0D = DTS3 1B = MPEG2 AAC1 1C = MPEG2 AAC2 20 = Silent 22 = DTS CD 23 = PCM TX-SR603/603E/8360 TX-SR603/603E/8360 EXPLODED VIEWS-1 A056 A068 x 37 pcs. A002 x 4 pcs. A061 x 6 pcs. A002 x 2 pcs. A002 x 3 pcs. A002 x 4 pcs. A002 x 4 pcs. A002 x 4 pcs. A046 x 2 pcs. A002 x 2 pcs. A111 x

41、2 pcs. A030 x 4 pcs. A002 x 3 pcs. A068 x 3 pcs. A002 x 2 pcs. A002 x 6 pcs. A018 x 4 pcs. A020 x 3 pcs. A021 x 2 pcs. A064 x 4 pcs. A066 x 8 pcs. A068 x 4 pcs. A002 x 3 pcs. U24 P101 P701 T901 P901 A093 A041 A073 A058 A001 A060 A017 A102 A109 DD, DC Only U04 U02 U08U06 U05 U09 U10 U18 U15 U17 U19 U

42、20 U03 U07 U01 U22 U12 U11 U13 A017 A017 A017 A070 A071 A081 A007 A054 A050 A006 A005A002 A077 A110 F903 F903c F901 F902 F902C F901C A052 A018 A002 A017 A002 A014 A031 A033 A022 A015 A017 A043 A017 F6902 F6901 F9501 F6901C A002 A017 F9501C Refer to in EXPLODED VIEWS-2 TX-SR603/603E/8360 TX-SR603/603

43、E/8360 EXPLODED VIEWS-2 Q6066 Q6056 Q6060 Q6061 Q6062 Q6063 Q6064 Q6054 Q6065 Q6055 Q6053 Q6052 Q6050 Q6051 Q6050A x 14 A049 x14 TX-SR603TX-SR603 BLOCK DIAGRAM FL_PO FR_PO CT_PO SBL_PO SBR_PO TAPE_OUT_R TAPE_OUT_L V2_OUT_L V2_OUT_R V1_OUT_L V1_OUT_R Z2_R Z2_L MIX_R MIX_L SOURCE_L SOURCE_R RECOUT_L R

44、ECOUT_R MCH_SR MCH_SL MCH_SW MCH_CT ADLT+ ADRT+ ADLT- ADRT- ADRT- ADRT+ ADLT+ ADLT- RX3 RX6 DAC_FL DAC_CT DAC_SW DAC_FR DAC_SR DAC_SBR DAC_SBL DAC_SL VOLIN_SBR VOLIN_SBL Z2R_PO Z2L_PO RX2 Z2LMUT Z2RL SBRL SPRLCS SW_PO AMUT SL_PO SR_PO TX RX4 RX1 RX0 SBMUT HPIN SPRLF TUNER UNIT NJW1157 CD TAPE OUT TA

45、PE IN VIDEO3 IN VIDEO2 OUT VIDEO2 IN VIDEO1 OUT VIDEO1 IN DVD (MULTI INPUT) COAXIAL IN 1 IN 2 IN 3 OUT 12V TRIGGER OUT ZONE 2 IR IN RI IR DE-MODULATOR RI INTERFACE PREOUT SUBWOOFER FRONT R CENTER SURROUND PHONES ZONE2 SURROUND BACK L SPEAKERS R L TONE TONE -6dB -6dB +9.7dB +20.2dB DIR 2ch ADC CS4251

46、8 8ch DAC +6dB VLSCLPF MIC AMP DSP SD_RAM IC42S16100 2M Byte CS494003 FLASH ROM MX29LV040 +6dB LPF LPF LPF LPF LPF LPF VLSCLPF 12V TRIGGER CONTROL R 4M Bit ZONE2 LINEOUT NJU7311 POWER AMPLIFIER +29dB +29dB +29dB +29dB +29dB +29dB +29dB SETUP MIC VIDEO4 INPUT IN 4 52 53 54 55 56 57 58 59 60 61 62 63

47、64 65 66 67 68 69 70 71 73 73 51 74 41 43 23 25 22 24 26 21 27 29 28 30 44 42 46 45 48 47 93 92 91 95 90 89 88 86 85 84 83 87 82 81 80 7 6 5 4 3 2 1 94 8 9 8 12 17 10 19 20 21 11 18 4 25 3 26 2 27 22 7 23 6 5 24 16 15 14 13 49 48 43 42 47 46 45 44 50 37 36 107 118 106 81 80 86 134 109 110 58 54 63 6

48、2 64 1 35 34 32 33 31 30 28 29 26 27 21 20 22 23 + + A A To Microprocessor INVERT VOLUME L R L L R FRONT CENTER SURROUND SUBWOOFER L R L R DIGITAL IN1 IN2 OPTICAL A 1 2 3 4 5 BCDEFGH TX-SR603TX-SR603 BLOCK DIAGRAM FL_PO FR_PO CT_PO SBL_PO SBR_PO TAPE_OUT_R TAPE_OUT_L V2_OUT_L V2_OUT_R V1_OUT_L V1_OU

49、T_R Z2_R Z2_L MIX_R MIX_L SOURCE_L SOURCE_R RECOUT_L RECOUT_R MCH_SR MCH_SL MCH_SW MCH_CT ADLT+ ADRT+ ADLT- ADRT- ADRT- ADRT+ ADLT+ ADLT- RX3 RX6 DAC_FL DAC_CT DAC_SW DAC_FR DAC_SR DAC_SBR DAC_SBL DAC_SL VOLIN_SBR VOLIN_SBL Z2R_PO Z2L_PO RX2 Z2LMUT Z2RL SBRL SPRLCS SW_PO AMUT SL_PO SR_PO TX RX4 RX1 RX0 SBMUT HPIN SPRLF