《Panasonic-SAAK230E-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Panasonic-SAAK230E-cs-sm 电路图 维修手册.pdf（109页珍藏版）》请在收音机爱好者资料库上搜索。
1、n AMPLIFIER SECTION RMS output power THD 10%, both channels driven 1 kHz,100 W per channel (5 ) Total RMS power200 W n FM/AM TUNER, TERMINALS SECTION Preset stationFM 15 stations AM 15 stations Frequency Modulation (FM) Frequency range 87.50 - 108.00 MHz (50 kHz steps) Sensitivity1.8 V (IHF) S/N 26
2、dB1.5 V Antenna terminal(s)75 (unbalanced) Amplitude Modulation (AM) Frequency range522 - 1629 kHz (9 kHz steps) Sensitivity S/N 20 dB (at 999 kHz)560 V/m Audio performance (Amplifier) Input sensitivity/Input impedance Aux250 mV,14.7 k Phone jack TerminalStereo, 3.5 mm jack n CASSETTE DECK SECTION T
3、rack system4 track, 2 channel Heads 2004 Matsushita Electric Industrial Co. Ltd. All rightsreserved.Unauthorizedcopyingand distribution is a violation of law. SA-AK230E SA-AK230EB SA-AK230EG Colour (S). Silver Type Record/playbackSolid permalloy head ErasureDouble gap ferrite head MotorDC servo moto
4、r Recording systemAC bias 100 kHz Erasing systemAC erase 100 kHz Tape speed4.8 cm/s Overall frequency response (+3 dB, -6 dB at DECK OUT) NORMAL35 Hz - 14 kHz S/N50 dB (A weighted) Wow and flutter0.18 % (WRMS) Fast forward and rewind timeApprox. 120 seconds with C-60 cassette tape n DISC SECTION Dis
5、cs played 8 cm or 12 cm (1) CD-Audio (CD-DA) (2) CD-R/RW (CD-DA, MP3 formatted discs) (3) MP3 Bit rate MP332 kbps - 320 kbps Sampling frequency MP332 kHz, 44.1 kHz, 48 kHz CD44.1 kHz Decoding16 bit linear Digital filter8 fs D/A converterMASH (1 bit DAC) Pickup CD Stereo System Specifications ORDER N
6、O. MD0412604C2 RadioFans.CN 收音机爱 好者资料库 Wavelength780 nm Beam SourceSemiconductor laser Audio output (Disc) Number of channels2 (Stereo) (FL,FR) n GENERAL Power Supply For E Typically the melting point is 50 - 70F (30 - 40C) higher. Please use a high temperature soldering iron. In case of soldering i
7、ron with temperature control, please set it to 700 20F (370 10C). Pb free solder will tend to splash when heated too high (about 1100F/600C). When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the soldering points with the Pb fre
8、e solder until it melts enough. 6 SA-AK230E / SA-AK230EB / SA-AK230EG 6 Handling Precautions For Traverse Deck The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity of clothes or human body. So, be careful of electrostatic break
9、down during repair of the traverse deck (optical pickup). Handling of traverse deck (optical pickup) 1. Do not subject the traverse deck (optical pickup) to static electricity as it is extremely sensitive to electrical shock. 2. To prevent the breakdown of the laser diode, an antistatic shorting pin
10、 is inserted into the flexible board (FFC board). 3. Take care not to apply excessive stress to the flexible board (FFC board). When removing or connecting the short pin, finish the job in as short time as possible. 4. Do not turn the variable resistor (laser power adjustment). It has already been a
11、djusted. Grounding for electrostatic breakdown prevention 1. Human body grounding Use the anti-static wrist strap to discharge the static electricity from your body. 2. Work table grounding Put a conductive material (sheet) or steel sheet on the area where the traverse deck (optical pickup) is place
12、, and ground the sheet. Caution : The static electricity of your clothes will not be grounded through the wrist strap. So, take care not to let your clothes touch the traverse deck (optical pickup). Caution when replacing the Traverse Deck The traverse deck has a short point shorted with solder to p
13、rotect the laser diode against electrostatics breakdown. Be sure to remove the solder from the short point before making connections. 7 SA-AK230E / SA-AK230EB / SA-AK230EG n Use of caution label 7 Precaution of Laser Diode Caution : This product utilizes a laser diode with the unit turned ON, invisi
14、ble laser radiation is emitted from the pick up lens. Wavelength : 780 nm Maximum output radiation power from pick up : 100 W/VDE Laser radiation from pick up unit is safety level, but be sure the followings: 1. Do not disassemble the optical pick up unit, since radiation from exposed laser diode is
15、 dangerous. 2. Do not adjust the variable resistor on the pick up unit. It was already adjusted. 3. Do not look at the focus lens using optical instruments. 4. Recommend not to look at pick up lens for a long time. ACHTUNG : Dieses Produkt enthlt eine Laserdiode. Im eingeschalteten Zustand wird unsi
16、chtbare Laserstrahlung von der Lasereinheit abgestrahlt. Wellenlnge : 780nm Maximale Strahlungsleistung der Lasereinheit :100 W/VDE Die Strahlung an der Lasereinheit ist ungefhrlich, wenn folgende Punkte beachtet werden: 1. Die Lasereinheit nicht zerlegen, da die Strahlung an der freigelegten Laserd
17、iode gefhrlich ist. 2. Den werkseitig justierten Einstellregler der Lasereinhit nicht verstellen. 3. Nicht mit optischen Instrumenten in die Fokussierlinse blicken. 4. Nicht ber lngere Zeit in die Fokussierlinse blicken. ADVARSEL: I dette a apparat anvendes laser. CAUTION! THIS PRODUCT UTILIZES A LA
18、SER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. 8 SA-AK230E / SA-AK230EB / SA-AK230EG 8 Accessories Remote Control FM Antenna AC Cord (For E QZZCWAT 14.1.1. Tape Speed Adjustment (Deck 1/2) 1. Set the tape
19、 edit button to “NORMAL” position. 2. Insert the test tape (QZZCWAT) to DECK 2 and playback (FWD side) the middle portion of it. 3. Adjust Motor VR (DECK 2) for the output value shown below. Adjustment target: 2940 3060 Hz (NORMAL speed) 4. After alignment, assure that the output frequency of the DE
20、CK 1 FWD are within 60 Hz of the value of the output frequency of DECK 2 FWD. Fig.1 14.1.2. Bias and Erase Voltage Check 1. Set the unit “AUX” position. 2. Insert the Normal blank tape (QZZCRA) into DECK 2 and the unit to “REC” mode (use “l REC/STOP” key). 3. Measure and make sure that the output is
21、 within the 1. Connect the instrument as shown in Fig.5. 2. Set the unit to AM mode. 3. Apply signal as shown in Fig. 5 from AM-SG. 4. Adjust Z2602 so that the output frequency is maximized in Fig. 6. standard value. Bias voltage for Deck 2144mV (Normal) Erase voltage for Deck 280mV (Normal) Fig.2 F
22、ig.3 14.1.3. Bias Frequency Adjustment (Deck 1/2) 1. Set the unit to “AUX” position. 2. Insert the Normal blank tape (QZZCRA) into DECK 2 and set the unit to “REC” mode (l use “REC/STOP” key). 3. Adjust L1002 so that the output frequency is within the standard value. Standard Value: 97 8 kHz Fig.4 F
23、ig.5 14 Measurements and Adjustments 14.2. Tuner Section 14.2.1. AM-IF Alignment 49 SA-AK230E / SA-AK230EB / SA-AK230EG Fig.6 14.2.2. AM RF Adjustment 1. Connect the instrument as shown in Fig. 7. 2. Set the unit to AM mode. 3. Set AM-SG to 520kHz. 4. Receive 520kHz in the unit. 5. Adjust Z2602 (OSC
24、) so that the EVM-AC is maximized. 6. Set AM-SG to 600Hz. 7. Receive 600Hz in the unit. 8. Adjust Z2602 (ANT) so that the EVM-SG is maximized. 14.3.1. Cassette Deck Section 14.3.2. Tuner Section 9. Set AM-SG to 520kHz. 10. Receive 520kHz in the unit. 11. Adjust L2602 (OSC) so that the EVM-DC value i
25、s with 1.10.5V. Fig.7 14.3. Alignment Points 50 SA-AK230E / SA-AK230EB / SA-AK230EG 15 Block Diagram T- T+ F+ F- PHOTODETECTOR OPTICAL PICKUP SEMICONDUCTOR LASER Q7601 LASER POWER DRIVE M7302 SPINDLE MOTOR RESET SIGNAL GENERATOR FOCUS COIL DRIVE TRACKING COIL DRIVE TRAVERSE MOTOR DRIVE SPINDLE MOTOR
26、 DRIVE MUTE CH2 FOCUS COIL TRACKING COIL D4+17 D4-16 D3+15 D3-14 D1+11 D1-10 D2+13 D2-12 4PC2 3IN2 6IN1 24IN3 23IN4 1 /RST NC 18 5 NC 2 NC B B B B IC7003 AN8739SBTE2 FOCUS COIL/TRACKING COIL/ TRAVERSE MOTOR/ SPINDLE MOTOR DRIVE M7301 TRAVERSE MOTOR E F B A LPD LD C D SPPOL SPOUT TRVP TRP FOP B B A B
27、 F E M M 51 SA-AK230E / SA-AK230EB / SA-AK230EG MN6627953HB SERVO PROCESSOR DIGITAL SIGNAL PROCESSOR/ DIGITAL FILTER/ D/A CONVERTER TO MAIN BLOCK IC7002 NTEST60 IOMODE59 NRST68 TIMING GENERATOR 71 X1 70 X2 (SMCK) (PMCK) MICRO COMPUTER INTERFACE 66 STAT 65 MLD 63 MCLK 64 MDATA DSL/PLL/VCO 44 ARFIN 46
28、 IREF 45 DSLF 47 PLLF 48 PLLF0 SUBCODE INTERFACE 43 AVSS2 49 AVDD2 67BLKCK 74 TXTD 73 DQSY (SBCK) (SUBC) (TXNCLDCK) 62 FLAG 1 EXT0 EFM DEMODULATION SYNC INTERPOLATION CIRC ECC CDROM ECC CIRC RAM 1 MBIT SRAM BUS CONTROL UNIT SPINDLE SERVO SERVO CPU RF INTERFACE RF AMPLIFIER INPUT PORT RFVDD37 VREF27
29、A,B,C,D,E,F3035 A, B, C, D, E, F CEA21 LD29 LD PD28 LPD DCDET36 CAGC41 2 EXT1 3 EXT2 76 GIO0 77 GIO1 78 GIO2 75TXTCK PORT ARF RFOUT39 RFIN40 FEN24 TEN25 FEOUT23 TEOUT26 (LRCK) (BCLK) (SRDATA) SERIAL OUTPUT INTERFACE REGULATOR LON (DVDD2) MP3/WMA DECODER FS CONVERTER DIGITAL FILTER 1 BIT DAC PWM LOGI
30、C ANALOG LOWPASS FILTER RFENV22 A/D CONVERTER ADPVCC18 FEIN20 TEIN19 RFENV22 OUTPUT PORT PWMSEL4 SPPOL6 SPPOL SPOUT5 SPOUT TRVP7 TRVP TRVM 8 TRVP2 9 TRVM2 10 TRP11 TRP TRM 12 FOP13 FOP FOM 14 IOVDD13 15, 56, 72 DVDD1,2 16, 57 DVSS13 17, 55, 69 DIGITAL OUT TX 61 OUTL 50 OUTR 54 AVDD1 53 AVSS1 51 (LRC
31、KIN) (BCLKIN) (SRDATIN) CD_RST STAT MLD MCLK MDATA BLKCK CD SIGNAL RCH A B X7201 B B B B B B FILTER B B B B B B 52 SA-AK230E / SA-AK230EB / SA-AK230EG IC2601 LA1833NMNTLM FM/AM IF AMP, DET/AM OSC, MIX/FM MPX SD ST SHIFT REGISTER LATCH 1 2 SWALLOW COUNTER 1/6,1/17,4 BITS 12 BITS PROGRAMMABLE DIVIDER
32、REFERENCE DIVIDER C2B I/F PLLCLK PLLDA ST/DO CE X2603 ST/DO SD S-CURVE REG FM IF FM DET AM OSC LEVEL DET BUFFER ALC DECODER STEREO SWITCH AM DET AM IF TUNING DRIVE AM/FM IF BUFFER COMP FFFF REG VCO AM MIX AM RM AMP AGC PHASE DET PILOT DET FF PILOT CANCEL (FM) TUNER 15V SUPPLY SWITCH Q2606 POWER ON R
33、ESET UNIVERSAL COUNTER UNLOCK DETECTOR PHASE DETECTOR CHARGE PUMP TO CD DRIVE BLOCK PLL FREQUENCY SYNTHESIZER LC72131MDTRM IC2602 X2602 16 17 18 11 15 19107698 4CL 3DI 2CE 5DO 13 12 14 20 1 L2602 D2602 L2601 232422212019181716141513 123465789101112 FM IF AMP Q2601 SWITCH Q2610 DET_OUT B B B B B RCH
34、A B CF2601CF2602 AM IFT Z2602 B B AM ANT FM ANT ENV17290G1Y 8 (FM) MIXER OSCBUFFER RF AMP 6 5 17 53 SA-AK230E / SA-AK230EB / SA-AK230EG MOTOR DRIVE C0GAM0000005 IC1 IC2801C2CBJG000565MICROPROCESSOR REG MLD MCLK CE MDATA SD CD_RST SWITCH BLKCK PLLCLK ST/DO PLLDA Q2906 STAT Q2907 RM1 SWITCH S7201 Q645
35、7 LED DRIVE SW5 LOCK SW4 CD SW3 SW1 SW2 POWER SUPPLY CONTROL Q1 Q2937 Q2936 CD MOTOR SUPPLY SWITCH PLUNGER MOTOR SUPPLY CONTROL SWITCH SSEQ_LED 76 RMT 18 D6457 MLD 79 MDATA 80 MCLK 81 22 SD 7721 ST/DO 78 STATUS 84 CHG_CW 85 CHG_CCW 88 CHG_PLR 83 CHG_HLF 89 CHG_AD2 90 CHG_AD1 86 CHG_SW1 87 CHG_SW2 PL
36、LCE 3 30 PLLCK 29 X_IN 15 X_OUT 13 V_JOG_A 67 V_JOG_B 68 /RESTSW 82 IN15 IN26 VREF 4 VCC 7 GND 1 10OUT2 2OUT1 8VS D2 PUSH PUSH OPEN X2802 XC_IN 10 XC_OUT 11 X2801 19 BLKCK C0HBB0000044 FL DRIVER IC6601 RESET 8 71 FL_RESET CS 3 72 FL_CS 74 FL_CLKSCK 9 SDATA 10 73 FL_DOUT XIN 5 XOUT 6 21, 23, 24, 2640
37、 3, 510, 12, 13, 15, 16, 18, 19 FL12 FL30 FL6601 FL DISPLAY FROM POWER TRANSFORMER 1, 2, 30401114, 1629 FL13 FL0 RDS_CLK RDS_DAT 2 DET_OUT 15 14 C1BB00000715 RDS CIRCUIT IC2809 89 X2803 54 B B B B B B CD_RST REMOTE SENSOR Z6481 D1 JOG VOL VR6491 PLLDA M 54 SA-AK230E / SA-AK230EB / SA-AK230EG AN7348S
38、-E1 P.B EQ/REC AMP/ ALC/TPS AMP IC1001 C1AA00000612 R/P SELECT IC1004 IC971 PHOTO INTERRUPTER CNB13030R2AU Q1003 SWITCHING (BEAT PROOF/ RECH) L1002 BIAS OSC CONTROL Q1004, Q1005, Q1007 NOR/CrO H: Tri-State 5SPOUTOSpindle driver output signal 6SPPOLOSpindle driver output signal 7TRVPOSpindle driver o
39、utput signal 8TRVMOSpindle driver output signal 9TRVP2OTraverse driver output signal 2 (+) 10TRVM2OTraverse driver output signal 2 (-) 11TRPOTraverse driver output signal (+) 12TRMOTraverse driver output signal (-) 13FOPOTraverse driver output signal (+) 14FOMOTraverse driver output signal (-) 15IOV
40、DD3-I/O power supply 3 16DVDD1-Powersupply1fordigital circuit 17DVSS1-Digital circuit GND 1 18ADPVCCIPower voltage monitor. Power voltage input 19TEINIDSPtraverseerrorsignal input 20FEINIDSP focus error signal input 21CEAI/OHPF-Ampcapacitance connection terminal 22RFENVORF envelope signal monitor 23
41、FEOUTOFE Amp output 24FENIFE Amp reversal input 25TENITE Amp reversal input 26TEOUTOTE Amp output 27VREFOVREF output 28PDIAPC Amp input 29LDOAPC Amp output 30EITracking input signal 1 31FITracking input signal 2 32DITracking input signal 4 33BITracking input signal 2 34CITracking input signal 3 35AI
42、Focus input signal 1 36DCDETIDetectionHPFcapacitance terminal 37RFVDD-RF Amp power supply 38RESERVE-AVSS2 39RFOUTORF Amp output 40RFINIAGC input 41CAGCI/OAGC control terminal 42ARFOUTOAGC output (Audio RF) 43AVSS2-Analog circuit GND 2 44ARFINIRF signal input 45DSLFODSL loop filter 46IREFII (current)
43、, Reference input 47PLLFOPLL loop filter 48PLLF0OPLL loop filter Pin No.MarkI/OFunction 49AVDD2-Analog circuit power supply 2 50OUTLOLCH output signal 51AVSS1-Audio output circuit GND 1 52N.C.-No Connection 53AVDD1-Powersupply1 for analog circuit 54OUTRORCH output signal 55DVSS2-Digital circuit GND
44、2 56IOVDD1-I/O power supply 1 57DVDD2-Powersupply2forDigital circuit 58REGONILaser diode control (H: ON) 59IOMODEII/O switching setting input 60NTESTITest mode setting input (H: ON) 61TXODigital audio interface output 62FLAGOFlag signal output 63MCLKIMicro-P serial command CLK 64MDATAIMicro-Pserialc
45、ommand DATA 65MLDIMicro-Pserialcommand LOAD 66STATOStatus signal output 67BLKCKOSubcode block clock 68NRSTILSI reset input (L: RESET) 69DVSS3-Digital circuit GND 3 70X2OCrystal oscillator circuit output 71X1ICrystal oscillator circuit input 72IOVDD2II/O power supply 2 73DQSYOPack signal outputfor CD
46、- Text data 74TXTDOCDText signal output 75TXTCKIExternal clock signal input for CD-Text register 76GIO0I/OGeneral purpose input/output Terminal 0 77GIO1I/OGeneral purpose input/output Terminal 1 78GIO2I/OGeneral purpose input/output Terminal 2 79GOUT0OGeneralpurposeoutput Terminal 0 80GOUT1OGeneralp
47、urposeoutput Terminal 1 21.2. IC7003 (AN8739SBTE2) Focus coil/ Tracking coil/ Traverse motor/ Spindle motor drive Pin No.MarkI/OFunction 1/RSTORESET output terminal 2N.C.-No Connection 3IN2IMotor drive (2) input 4PC2ITurntable motor drive signal (“L” :ON) 5N.C.-No Connection 6IN1IMotor driver (1) in
48、put 7PVCC1-Power supply (1) for driver 8PGND1-Ground connection (1) for driver 9N.C.-No Connection 10D1-OMotor driver (1) reverse-action output 11D1+OMotor driver (1) forward-action output 12D2-OMotor driver (2) reverse-action output 21 Terminal Function of ICs 87 SA-AK230E / SA-AK230EB / SA-AK230EG
49、 Pin No.MarkI/OFunction 13D2+OMotor driver (2) forward-action output 14D3-OMotor driver (3) reverse-action output 15D3+OCrystal oscillating circuit input (f = 16.9344MHz) 16D4-OMotor driver (4) reverse-action output 17D4+OMotor driver (4) forward-action output 18N.C.-No Connection 19PGND2-Ground connection (2) for driver 20PVCC2-Power supply (2) for driver 21VCC-Power supply terminal 22VREF-Reference voltage input 23IN4IMotor driver (4) input 24IN3IMotor driver (3) input 25RSTINIReset terminal 26N.C.-No Connection 21.3. IC28
免费区 
