Panasonic-SAAK350PL-cs-sm 电路图 维修手册.pdf

《Panasonic-SAAK350PL-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Panasonic-SAAK350PL-cs-sm 电路图 维修手册.pdf（103页珍藏版）》请在收音机爱好者资料库上搜索。

1、RMS output power THD 10%, both channels driven 1 kHz (Low channel)112.5 W per channel (3 ) 10 kHz (High channel)112.5 W per channel (3 ) Total Bi-Amp power450 W PMPO4800 W n FM/AM TUNER, TERMINALS SECTION Preset stationFM 20 stations AM 15 stations Frequency Modulation (FM) Frequency range87.9 to 10

2、7.9 MHz (200 kHz steps) 87.5 to 108.0 MHz (100 kHz steps) Sensitivity4.0 V (IHF) S/N 26 dB2.2 V Antenna terminal(s)75 (unbalanced) Amplitude Modulation (AM) Frequency range520 to 1710 kHz (10 kHz step) Sensitivity S/N 20 dB (at 1000 kHz)560 V/m Audio performance (Amplifier) 2007 Matsushita Electric

3、Industrial Co. Ltd. All rightsreserved.Unauthorizedcopyingand distribution is a violation of law. SA-AK350PL Colour (S). Silver Type Input Sensitivity/ Input Impedance Aux250 mV, 14.7 k Music Port input jack TerminalStereo, 3.5 mm jack Sensitivity100 mV, 4.7 k Phone jack TerminalStereo, 3.5 mm jack

4、Mic jack TerminalMono, 3.5 mm jack Sensitivity0.7 mV, 680 n CASSETTE DECK SECTION Track system4 track, 2 channel Heads Record/playbackSolid permalloy head ErasureDouble gap ferrite head MotorDC servo motor Recording systemAC bias 100 kHz Erasing systemAC erase 100 kHz Tape speed4.8 cm/s Overall freq

5、uency response (+3, -6 dB) at DECK OUT NORMAL35 Hz to 14 kHz S/N ratio50 dB (A weighted) Wow and flutter0.18 % (WRMS) CD Stereo System Notes: This models CD mechanism changer unit is CRS1. Please refer to the original Service Manual (Order No. MD0509368C0) for this mechanism. Specifications ORDER NO

6、. MD0704045CE RadioFans.CN 收音机爱 好者资料库 Fast forward and rewind timeApprox. 120 seconds with C-60 cassette tape n DISC SECTION Disc played 8 cm or 12 cm (1) CD-Audio (CD-DA) (2) CD-R/RW (CD-DA, MP3* formatted disc) (3) MP3* *MPEG-1 Layer 3, MPEG-2 Layer 3 Bit rate MP332 kbps to 320 kbps Sampling frequ

7、ency MP332 kHz, 44.1 kHz, 48 kHz CD-DA44.1 kHz Decoding16 bit linear Digital filter8 fs D/A converterMASH (1 bit DAC) Pick up Wavelength780 nm Beam SourceSemiconductor laser Audio output (Disc) 1 Safety Precautions 4 1.1. General Guidelines 4 1.2. Before repair and adjustment 4 1.3. Protection Circu

8、itry 5 1.4. Safety Part Information 5 2 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices 5 3 Handling Precautions For Traverse Deck 7 4 Precaution of laser diode 9 5 About Lead Free Solder (PbF) 10 5.1. Service caution based on legal restrictions 10 6 Accessor

9、ies 11 7 Operating Procedures 12 7.1. Main Unit Key Buttons Operations 12 7.2. Remote Control Key Buttons Operations 13 8 New Features 14 8.1. Using the Music Port 14 9 Self diagnosis and special mode setting 16 9.1. Service Mode Summary Table 16 9.2. Special Mode Table 1 16 9.3. Reliability Test Mo

10、de (CRS1 Mechanism) 19 9.4. Error code Table Display 21 10 Assembling and Disassembling 26 10.1. Caution 26 10.2. Disassembly flow chart 27 Number of channels2 (Stereo) (FL, FR) n GENERAL Power supplyAC 120 V, 60Hz Power consumption115 W Powerconsumptioninstandby mode 0.28 W Dimensions (W x H x D)25

11、0 x 330 x 323 mm Mass7.1 kg Operating temperature range+5 to +35C Operating humidity range5 to 90% RH (no condensation) n SYSTEM SC-AK350 (PL)Music center: SA-AK350 (PL) Speaker: SB-AK350 (PL) For Information on speaker system, plesae refer to the original Service Manual (Order No. MD0704046CE) for

12、SB-AK350PL-S. Notes: 1. Specifications are subject to change without notice. Mass and dimensions are approximate. 2. Total harmonic distortion is measured by the digital spectrum analyzer. 10.3. Main Parts Location 28 10.4. Disassembly of Top Cabinet 29 10.5. Disassembly of CD Changer Unit (CRS1) 29

13、 10.6. Disassembly of Rear Panel 30 10.7. Disassembly of Main P.C.B. 31 10.8. Disassembly of Transformer P.C.B. 31 10.9. Disassembly of Power P.C.B. 32 10.10. Disassembly of Front Panel Unit 33 10.11. Disassembly for Panel P.C.B. 34 10.12. Disassembly of Tact Switch P.C.B. 34 10.13. Disassembly of D

14、eck mechanism unit 35 10.14. Disassembly of Deck P.C.B. 35 10.15. Disassembly of Traverse Unit 35 10.16. Disassembly for Deck Mechanism 37 10.17. Disassembly of Deck Mechanism P.C.B. 39 10.18. Disassembly of cassette lid 40 10.19. Rectification for tape jam problem 40 11 Service Fixture and Tools 42

15、 12 Service Positions 42 12.1. Checking and Repairing of Main P.C.B. 42 12.2. Checking and Repairing of Transformer P.C.B. 43 12.3. Checking and Repairing of Panel, Deck /Serial I/P (No connection) 17BA1-Motor O/P (1);/Serial I/P (No connection) 18PRAMVSS33-GND (DRAM) 19PRAMVDD33-Power Supply Voltag

16、e (DRAM) 20PRAMVDD15-Power Supply Voltage (+1.6V) 21SPOUTOSpindle Drive O/P 22PCI/OSpindle motor drive O/P signal 23TRVPOTraverse Drive O/P (+ve) 24TRPOTracking Drive O/P (+ve) 25FOPOFocusing Drive O/P (+ve) 26DVSS1-GND 27IOVDD2-Digital Power Supply Voltage 2 (I/O) 28DVDD1-Digital Power Supply Volta

17、ge 1 (Built-In) 29SRVMON0-Servo Monitor (0) O/P (No connection) 30SRVMON1-Servo Monitor (1) O/P (No connection 31AVSS2-GND 32OSCIN-Oscillating Input 33CTRCRS-Tracking Cross Comparator Terminal 34VREF-+Vref Supply Voltage 35EITracking Input Signal 1 36FITracking Input Signal 2 37DIFocusing Input Sign

18、al 4 38BIFocusing Input Signal 2 39CIFocusing Input Signal 3 40AIFocusing Input Signal 1 41PDIAPC Amp I/P 42LDOLaser Drive Current O/P 43CENV-Detection Capacitance Connection terminal 44RFENVORF Envelope O/P 45RFOUTORF Summing Amp O/P 46RFINISGC I/P 47AVDD2-Analog Power Supply voltage 2 (For DSL/PLL

19、) 48ARFDC-AGC Capacitive Connection Terminal 49ARFOUTOAGC Output 50ARFFBIARF Feedback Signal I/P 51ARFINIAudio RF Signal I/P 52DSLF-Loop Filter Terminal (For DSL) Pin No.MarkI/OFunction 53IREFIReference I/P 54PLLF-PLL Loop Filter Terminal (Phase Compare) 55PLLF0-PLL Loop Filter Terminal (Speed Compa

20、re) 56OUTLOAudio O/P (LCH) 57AVSS1-GND 58AVDD1-Analog Power Supply Voltage 1 59OUTROAudio O/P (RCH) 60DVSS3-GND3 (Digital Circuit) 61NSRVMONONOServo Motor O/P Enabling 62EXT0OExpansion O/P Port 0 63EXT1OExpansion O/P Port 1 64EXT2OExpansion O/P Port 2 65FLAG-Flag Signal O/P (No connection) 66TX-Digi

21、tal Audio Interface O/P signal 67MCLKIMicro-Computer Command Clock I/P 68MDATAIMicro-Computer Data I/P 69MLDIMicro-Computer Load I/P 70STATOStatus Signal O/P 71*BLKCKOSubcode Blk Clock 72NRSTOLSI Reset Signal 73*DQSYTXT-Pack Signal O/P for CD-Text data (No connection) 74*SMCK-Micro-Computer Clock O/

22、P (No connection) 75*PMCK-IOCNT Serial data O/P (Synchronous O/P) (No connection) 76DVDD2-Digital Power Supply Voltage 2 (+1.5V) 77IOVDD1-Digital Power Supply Voltage 1 (For I/O) 78DVSS2-GND2 (For Digital Circuit) 79NTEST2ITest Mode Setting (ON:H) 80X2OCrystal Oscillating Circuit O/P 81X1ICrystal Os

23、cillating Circuit I/P 82NTESTITest Mode Setting I/P (ON:H) 83D2I/OData Sigmal O/P 2 84D1I/OData Signal O/P 1 85D0I/OData Signal O/P 0 86D3I/OData Signal O/P 3 87D4I/OData Signal O/P 4 88D5I/OData Signal O/P 5 89D6I/OData Signal O/P 6 90D7I/OData Signal O/P 7 91D15I/OData Signal O/P 15 92D14I/OData S

24、ignal O/P 14 93DRVDD-I/O Power Supply Voltage (DRAM) 94D13I/OData Signal O/P 13 95D12I/OData Signal O/P 12 96D11I/OData Signal O/P 11 97D10I/OData Signal O/P 10 98D9I/OData Signal O/P 9 99D8I/OData Signal O/P 8 100SDRCKOClock Signal O/P 22 Terminal Function of ICs 22.1. IC7001 (MN6627954MA) Servo Pr

25、ocessor,Digital Signal Processor/Digital filter and D/A Converter 86 SA-AK350PL Pin No.MarkI/OFunction 1IN2IMotor Driver 92 Input 2PC2ITurntable Motor Drive Signal (“L”:ON) 3IN1IMotor Drive (1) Input 4PC1-Traverse Motor Drive Signal (“L”): ON) 5-8N.C.-No Connection 9PGND1-Ground Connection (1) for D

26、rive 10PVCC1-Power Supply (1) for Drive 11D1-OMotor Drive (1) reverse - action output 12D1+OMotor Drive (1) forward - action output 13D2-OMotor Drive (2) reverse - action output 14D2+OMotor Drive (2) forward - action output Pin No.MarkI/OFunction 1LM_1I/OLevel Meter 2D_PORT DET1ID-Port DET 1 3D_PORT

27、 DET2ID-Port DET 2 4RDS_DAT-No connection 5RDS_CLK-No connection 6IP_LINK-No connection 7F_HOPOF_Hop for Digital Amp 8BYTE-External Data Bus Width Select Input (Connect to Ground) 9CNVSS-Flash Mode Terminal 10Xcin-32.768 kHz Sub Clock 11Xcout-32.768 kHz Sub Clock 12/RESET-/RESET Input (ACTIVE L) 13X

28、out-10 MHz Main Clock 14Vss-Ground (0V) 15Xin-10 MHz Main Clock 16Vcc-Power Supply (+5V) 17/NMI-Connect to Vcc (+5V) 18RMTIRemote Control Input 19BLKCKICD Block Clock Input (Inverted) 20SYNCIAC Failure Detect Input 21D0OSerial Output Data 22DIISerial Input Data 23S/WOOFER CSISubwoofer Chip Select 24

29、SW_LVL1-No connection 25SW_LVL2-No connection 26ASP DATOASP Data 27ASP_CLKOASP Clock 28FL CSIAK model Chip Select 29PLL_DATA-No connection 30PLL_CLKI/OTuner PLL Clock 31USB_SDA (TxD)I/OUSB I2C data line (Flash Tx for On board writer) 32USB_SCL (RxD)I/OUSB I2C Clock line (Flash RxD for On board write

30、r) 33USB_RSTOUSB Reset Pin. 34XM_MUTE (BUSY)-No connection 35XM_TX_OUT-Verify Error for USB Version up Using CD 36XM_RX_IN-No connection 37XM_I2S_RATE-No connection 38XM_LINK ACTIVE-No connection 39MUTE_DAOD-Amp Muting Control Pin No.MarkI/OFunction 15D3-OMotor Drive (3) reverse - action output 16D3

31、+OMotor Drive (3) forward - action output 17D4-OMotor Drive (4) reverse - action output 18D4+OMotor Drive (4) forward - action output 19PVCC2-Power Supply (2) for Driver 20PGND2-Ground Connection (2) for Driver 21-24N.C.-No Connection 25VCC-Power Supply terminal 26VREF-Reference Voltage Input 27IN4I

32、Motor Driver (4) Input 28IN3IMotor Driver (3) Input Pin No.MarkI/OFunction 40MUTE_AOAudio Muting Control 41EE_CS/EFP/EPMOEEPROM Chip Select (Flash EPM for On board writer) 42EE_CLKOEEPROM CLOCK 43EE_DATI/OEEPROM DATA 44XM_DAC_ RESET-No connection 45XM_ANT_REV-No connection 46PCONT/EFP/CSOPower Contr

33、ol Output 47DCDETIDC Detect Input 48XM_RST-No connection 49XM_PCONT-No connection 50STANDBYOFor Digital AMP 5-0v during FHOP 51VOL_LEDOVolume LED Drive 52CEITUNER CE 53DMTODeck mute at mecha transition. L=mute OFF, H=mute ON 54BOTTOM_SWIBottom switch for CRS1 55UP_SENSORIUp/Down sensor for CRS1 56PL

34、GOPlunger Control O/P 57PHOTOIPhoto (SG mechanism only) 58MTRI/ODeck motor control (“L” for motor OFF) 59RECI/OH when record circuit is operating 60MMOD0IMicon Mode Switching for USB Version Up using CD 61PAM CSIPAM Region Model Chip Select 62VCC-Power Supply (+5V) 63H BASS_LEDOHarmonic Bass LED Dri

35、ve 64Vss-Ground (0V) 65D-PORT_R-SKIP-No connection 66D-PORT_F-SKIP-No connection 67D-PORT_STOP-No connection 68D-PORT_RES2-No connection 69D-PORT_RES1-No connection 70FL_CSOFL Driver Chip Select 71FL_DOUTOSerial Data To FL Driver 72FL_CLKOSerial Clock To FL Driver 73VOL_LED_CSIVOL LED Chip Select 74

36、USB_REQIUSB Request. 75STATUSICD Servo LSI Status Input 76MLDI/OCD Command Load Output 22.2. IC7002 (BA5948FPE2) IC 4CH Drive 22.3. IC2801 (C2CBYY000482) System Microprocessor 87 SA-AK350PL Pin No.MarkI/OFunction 77MDATA_OUTI/OCD Command Data Output 78MCLKI/OCD Command Clock Output 79/RESET_SWICD Li

37、mit Switch Input for the most Inner Point (Active Low) 80HOME_SWIHome Switch for CRS1 81CD_RSTI/OCD Reset output 82CLOSE_SWICLOSE switch for CRS1 83OPEN_SWIOpen switch for CRS1 84CWOCRS1 motor CW 85CCWOCRS1 motor CCW 86ST_SWIStock switch for CRS1 87PLAY_SWIPlay switch for CRS1 88PLUNGEROPlunger for

38、CRS1 89REG-Region Setting 90VOL_JOGIVolume jog 91D-PORT_PCONT-No connection 92KEY3IKey 3 Input 93KEY2IKey 2 Input 94KEY1IKey 1 Input 95DECK_AD1IDeck AD input 1 96AVSS-Analog Power Supply Input (Connect to GND) 97DECK_AD2IDeck AD input 2 98VREF-Reference for A-D (5V) 99AVCC-Analog Power Supply Input

39、100DEMO_SETI(H= Default demo On, L= Default demo off) 88 SA-AK350PL 23 Exploded Views 23.1. Cabinet Parts Location SA-AK350PL 89 SA-AK350PL 90 23.2. Deck Mechanism Parts Location (RAA4403-S) SA-AK350PL 91 23.3. Packaging SA-AK350PL 92 Notes: Ref. No.Part No.Part Name & DescriptionRemarks CABINET AND

40、 CHASSIS 1J3CCBB000009TUNER PACKM 2REEV013921P FFC (DECK)M 3REEV014022P FFC (CD)M 5REEV019030P FFCM 6REEX074714P FFC WIREM 7RGKV0158-KCD LIDM 9RGLV0069-QVOLUME KNOB LIGHTM 10RGLV0070-QPOWER BUTTON LIGHTM 11RGPV0105-SFRONT PANELM 12RGRV0052B-BREAR PANELM 14RGUV0163-KSELECTOR BUTTONM 15RGUV0164-SCD CH

41、ANGER/POWER BTNM 16RGUV0165-S5CD CHANGE BUTTONM 17RGUV0166-KFUNCTION BUTTON LM 18RGUV0167-KFUNCTION BUTTON RM 19RGUV0177-1S7 CONTROL BUTTONM 20RGWX0056-3SMIC VOL KNOBM 21RGWX0072-1SVOL KNOBM 22RHD26046-LSCREWM 23RMC0158-S2TRANSISTOR HOLDERM 24RHD30007-1SJSCREWM 25RHD30111-3SCREWM 26RHD30119-SSCREW (

42、SILVER)M 27RKA0072-KJLEG CUSHIONM 28RKFV0062-1SCASSETE LIDM 29RKMV0071-SJTOP PANELM 30RKWV0068F-KFL WINDOWM 31RMBV0042-2CASS LID SPRINGM 32RMBV0052DVD LID SPRINGM 33RMGX0033CUSHION RUBBERM 34RMGX0044-1D.AMP. INSULATORM 35L6FALEFH0030FAN UNITM 36RMKX0113-3CD CHASSISM 37RMKX0118ABOTTOM CHASSISM 38RMQV

43、0076-WREFLECTORM 39RMVV0073-KFL WINDOW BACKGROUNDM 40RMYX0131-1SUB HEAT SINKM 44RUS757ZAACASS HALF SPRINGM Ref. No.Part No.Part Name & DescriptionRemarks 45RXGX0002DAMPER GEARM 46RXXV0048HEATSINK UNITM 48XTV3+10GFJ-MSCREWM 49XTW3+12TFJSCREWM 50XTWS3+6TFJSCREWM 51REXX03259P FLAT WIREM 52REXX0324-19P

44、FLAT WIREM 53RMNV0079FL HOLDERM 54RMNV0059LED HOLDERM 55XTW3+10TFCSCREWM CASSETTE DECK 101RED0067-2P/B HEADM 103RDG0300REEL BASE GEARM 104RDG0301WINDING RELAY GEARM 105RDK0026-4MAIN GEARM 107RDV0033-4WINDING BELTM 108RDV0064-1CAPSTAN BELTM 110RMB0312TRIGGER LEVER SPRINGM 111RMB0400REEL SPRINGM 112RM

45、B0403HEAB PANEL SPRINGM 113RMB0404BRAKE ROD SPRINGM 114RMB0406-5FR LEVER SPRINGM 115RMB0408THRUST SPRINGM 116RML0370-4TRIGGER LEVERM 117RML0371FR LEVERM 118RML0372-2WINDING LEVERM 119RML0374-2EJECT LEVERM 120RMM0131-1BRAKE RODM 121RMM0133-1EJECT RODM 122RMQ0519REEL HUBM 123RMS0398-1MOVING COREM 124R

46、XQ0470-2PLUNGER ASSYM 125RMC0061PACK SPRINGM 126RXF0061-1FLYWHEEL F ASSYM 128RXG0040FF RELAY GEAR ASSYM 129RMK0283A-2SUB-CHASSISM 130RXL0124PINCH ROLLER F ASSYM 130-1RMB0401PINCH ARM SPRING FM 24 Replacement Parts List Important safety notice: Components identified bymark have special characteristic

47、s important for safety. Furthermore, special parts which have purposes of fire-retardent (resistors), high-quality sound (capacitors), low noise (resistors), etc are used. When replacing any of these components, be sure to use only manufacturers specified parts shown in the parts list. The parenthes

48、ized indications in the Remarks columns specify the areas or colour. (Refer to the cover page for area or colour) Parts without these indications can be used for all areas. Warning: This product uses a laser diode. Refer to caution statements on “Precaution of Laser Diode”. Capacitor values are in m

49、icrofarads (F) unless specified otherwise, P= Pico-farads (pF), F= Farads. Resistance values are in ohms, unless specified otherwise, 1K=1,000 (OHM). The marking (RTL) indicates that the Retention Time is limited for this items. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention period of a availability is dependent on the type of assembly, and in accordance with the laws governing part and product retention. After the