Yamaha-MCRB043-cs-sm 电路图 维修手册.pdf

《Yamaha-MCRB043-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Yamaha-MCRB043-cs-sm 电路图 维修手册.pdf（87页珍藏版）》请在收音机爱好者资料库上搜索。

1、IMPORTANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifi cally Yamaha Products, are already known and understood by the users, and have therefore

2、 not been restated. WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specifi ed. For these reasons, we advise all Yamaha product owners that an

3、y service required should be performed by an authorized Yamaha Retailer or the appointed service representative. IMPORTANT: The presentation or sale of this manual to any individual or fi rm does not constitute authorization, certifi cation or recognition of any applicable technical capabilities, or

4、 establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifi cations are, therefore, i

5、nevitable and specifi cations are subject to change without notice or obligation to retrofi t. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have ac

6、cumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. SERVICE MANUAL CONTENTS TO SERVICE PERSONNEL .2 PREVENTION OF ELEC

7、TROSTATIC DISCHARGE .4 SYSTEM COMPOSITION / 構成 .5 FRONT PANELS .6 REAR PANELS .7 REMOTE CONTROL PANEL .9 SPECIFICATIONS / 参考仕様 .10 INTERNAL VIEW .13 SERVICE PRECAUTIONS / 時注意事項 .13 DISASSEMBLY PROCEDURES / 分解手順 .14 UPDATING FIRMWARE / .18 SELF-DIAGNOSTIC FUNCTION / （自己診断機能） .25 DISPLAY DATA .41 IC D

8、ATA .43 PIN CONNECTION DIAGRAMS .47 BLOCK DIAGRAM .49 WIRING DIAGRAMS .50 PRINTED CIRCUIT BOARDS .52 SCHEMATIC DIAGRAMS .57 REPLACEMENT PARTS LIST .63 REMOTE CONTROL .85 MICRO COMPONENT SYSTEM P.O.Box 1, Hamamatsu, Japan 15.12 Copyright (c) Yamaha Corporation All rights reserved. This manual is copy

9、righted by Yamaha and may not be copied or redistributed either in print or electronically without permission. 101 3 4 9 MCR-B043/MCR-B043D/NS-BP83 Note: When the BT-CARD P.C.B. is replaced, Factory Preset in Self-diagnostic function menu 15-2. must be preformed in order to have the BT-CARD P.C.B. t

10、o operate properly. If Factory Preset is not preformed, proper model name will not appear during pairing process. (For details, refer to “15. FACTORY PRESET” menu of the self-diagnostic function) 注意： BT-CARD P.C.B. 交換、BT-CARD P.C.B. 正常動作 15-2. 初期化実行 。 初期化実行場合、Bluetooth 機器行正名表示。 （詳細 “15. FACTORY PRES

11、ET” 参照） MCR-B043/MCR-B043D/ NS-BP83 RadioFans.CN 收音机爱 好者资料库 WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE 1. Critical Components Information Components having special characteristics are marked and must be replaced with parts having specifications equal to those o

12、riginally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedance should be equivalent to 1500 ohms shunted by 0.15 F. TO SERVICE PER

13、SONNEL Leakage current must not exceed 0.5mA. Be sure to test for leakage with the AC plug in both polarities. 本機搭載基板付 接合部無鉛付。 無鉛種類、修理時 下記無鉛使用推奨。 Sn+Ag+Cu（錫 + 銀 + 銅） Sn+Cu（錫 + 銅） Sn+Zn+Bi（錫 + 亜鉛 + ） 注意： 無鉛融点温度通常鉛入比 30 40程度高、 合 使用。 All of the P.C.B.s installed in this unit and solder joints are solde

14、red using the lead free solder. Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth) Caution: As the melting point temperature

15、 of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder. About lead free solder / 無鉛 CALIFORNIA PROPOSITION 65 WARNING This product contains chemicals known to the State of California to cause cancer, or b

16、irth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If y

17、ou come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. WARNING: Laser Safety This product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause eye damage. To protect

18、 your eyes and skin from laser radiation, the following precautions must be used during servicing of the unit. 1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm/1 feet away from the laser pick-up unit at all times. Do not stare at the laser be

19、am at any time. 2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual. 3) CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. 2 MCR-B043/MCR-B043D/NS-B

20、P83 MCR-B043/MCR-B043D/ NS-BP83 RadioFans.CN 收音机爱 好者资料库 U, T, K, A, B, G, L, S, H, J models V model T model * The new loader mechanism unit has no LASER CAUTION label attached. When replacing the loader mechanism unit with a new one, reattach the LASER CAUTION label from the old unit to the new unit

21、. 新 LASER CAUTION貼 。 新 交換場合、LASER CAUTION 貼直。 Laser Emitting conditions: 1) When the Top Cover is removed, and the STANDBY/ON SW is turned to the “ON” position, the laser component will emit a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate

22、 through the lens of the laser pick-up unit. Do not attempt any servicing during this period! If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any laser emissions. 2) The laser power level can be adjusted with the VR on the pick-up PWB,

23、 however, this level has been set by the factory prior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this manual. Adjustment of this control can increase the laser emission level from the device. Type: Semiconductor laser GaAS/GaAlAs

24、 Wave length: 790 nm Output Power: 7 mW Laser Diode Properties The primary side of the power supply carries live mains voltage when the player is connected to the mains even when the player is switched off ! This primary area is not shielded so it is possible to accidentally touch copper tracks and/

25、or components when servicing the player. Service personnel have to take precautions to prevent touching this area or components in this area. Note: The screws on the Loader mechanism may never be touched, removed or re-adjusted. Handle the Loader mechanism with care when the unit has to be exchanged

26、! The Loader mechanism is very sensitive for dropping or giving shocks. Warning for power supply 3 MCR-B043/MCR-B043D/NS-BP83 MCR-B043/MCR-B043D/ NS-BP83 RadioFans.CN 收音机爱 好者资料库 1M-ohms Conductive material (sheet) or steel sheet Anti-static wrist strap Some semiconductor (solid state) devices can be

27、 damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce th

28、e incidence of component damage caused by electro static discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available dischargin

29、g ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or expos

30、ure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protect- ed)” can generate electrical charge sufficient to damage ES devices. 5. Do not u

31、se freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted to

32、gether by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no

33、 power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as brushing together of your fabric clothes or lifting of your foot from a carpeted floor can generate st

34、atic electricity (ESD) sufficient to damage an ES device). Grounding for electrostatic breakdown prevention 1. Human body grounding. Use the antistatic wrist strap to discharge the static electricity from your body. 2. Work table grounding. Put a conductive material (sheet) or steel sheet on the are

35、a where the optical pickup is placed and ground the sheet. Caution: The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes touch the optical pickup. PREVENTION OF ELECTROSTATIC DISCHARGE 4 MCR-B043/MCR-B043D/NS-BP83 MCR-B043/MCR-B043

36、D/ NS-BP83 SYSTEM COMPOSITION / 構成 The MCR-B043 consists of the main unit and NS-BP83. The MCR-B043D consists of the main unit and NS-BP83. MCR-B043 、 NS-BP83 構成 。 NS-BP83 NS-BP83 NS-BP83 NS-BP83 MAIN UNIT MAIN UNIT MCR-B043 MCR-B043D 5 MCR-B043/MCR-B043D/NS-BP83 MCR-B043/MCR-B043D/ NS-BP83 FRONT PA

37、NELS MCR-B043D NS-BP83 MCR-B043 6 MCR-B043/MCR-B043D/NS-BP83 MCR-B043/MCR-B043D/ NS-BP83 REAR PANELS MCR-B043 U model T model K model G model L, H models V model 7 MCR-B043/MCR-B043D/NS-BP83 MCR-B043/MCR-B043D/ NS-BP83 S model J model A model B, G models MCR-B043D NS-BP83 8 MCR-B043/MCR-B043D/NS-BP8

38、3 MCR-B043/MCR-B043D/ NS-BP83 REMOTE CONTROL PANEL Color Variations / * Stripes design of NS-BP83 front panel / NS-BP83 柄 BL:Black color WH: White color BU:Blue color RE:Red color OR: Orange color DG: Dark Gray color LB:Light Blue color BG: Beige color DN: Dark Green color YE:Yellow color OR: Orange

39、/White colors DG: Dark gray/Silver colors YE:Yellow/Black colors 9 MCR-B043/MCR-B043D/NS-BP83 MCR-B043/MCR-B043D/ NS-BP83 Bluetooth Section / Bluetooth 部 Bluetooth Version / Bluetooth .Ver. 3.0 Supported Profile / 対応 . A2DP (Advanced audio distribution profile) AVRCP (Audio/video remote control prof

40、ile) Supported Audio CODEC / 対応 .SBC RF Output Power / 無線出力 . Class 2 Maximum Communication Range / 最大通信距離 . 10 m (without interference / 妨害時 ) Supported Contents Protection / 対応保護 .SCMS-T method Others / 他 CLOCK Lunar Inequality / 月差 .47 second ALARM/SLEEP Function / 機能 .Alarm, Snooze, Sleep Alarm

41、Mode / .Beep, Source, Source + Beep Source: CD, USB, Radio, DAB (MCR-B043D) General / 総合 Power Supply/Frequency / 電源電圧周波数 U model .AC 120 V, 60 Hz T model .AC 220 V, 50 Hz K model .AC 220 V, 60 Hz A model .AC 240 V, 50 Hz B, G models .AC 230 V, 50 Hz L, H models . AC 220240 V, 50/60 Hz V model . AC 110120 V, 60 Hz S model . AC 110240 V, 60 Hz J model .AC 100 V, 50/60 Hz Power Consumption / 消費電力 .30 W System Off Consumption / 時消費電力 Clock display: ON .3.5 W or less Power Save Consumption / 省電力時消費電力 .0.5 W or less Dimensions (W x H x D) / 寸法（幅高