《Panasonic-SAHT530EB-htss-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Panasonic-SAHT530EB-htss-sm 电路图 维修手册.pdf（104页珍藏版）》请在收音机爱好者资料库上搜索。
1、n Amplifier Section RMS Output Power: Dolby Digital Mode Front Ch 55 W per channel (6 ), 1 kHz, 10% THD Surround Ch 55 W per channel (6 ), 1 kHz, 10% THD Center Ch 160 W per channel (6 ), 1 kHz, 10% THD Subwoofer Ch 220 W per channel (4 ), 100 Hz, 10% THD Total RMS Dolby Digital Mode Power600 W DIN
2、Output Power: Dolby Digital Mode Front Ch 40 W per channel (6 ), 1 kHz, 1% THD Surround Ch 40 W per channel (6 ), 1 kHz, 1% THD Center Ch 120 W per channel (6 ), 1 kHz, 1% THD Subwoofer Ch 150 W per channel (4 ), 100 Hz, 1% THD Total DIN Dolby Digital Mode Power430 W n FM/AM Tuner, Terminals Section
3、 Preset stationFM 15 stations AM/MW 15 stations Frequency Modulation (FM) Frequency Range 87.50-108.00 MHz (50-kHz step) 2005 Matsushita Electric Industrial Co. Ltd. All rightsreserved.Unauthorizedcopyingand distribution is a violation of law. SA-HT530EB Colour (S).Silver Type Sensitivity1.5 V (IHF)
4、 S/N 26 dB1.2 V Antenna terminals75 (unbalanced) Amplitude Modulation (AM/MW) Frequency Range522-1629 kHz (9-kHz step) AM Sensitivity S/N 20 dB at 999 kHz560 V/m Phone Jack TerminalStereo, 3.5 mm jack n Disc Section Disc played 8 cm or 12 cm 1. DVD-RAM (DVD-VR compatible, JPEG formatted disc) 2. DVD
5、-Audio 3. DVD-Video 4. DVD-R, DVD-RW (DVD-Video compatible) + R, + RW (Video compatible) 5. CD-Audio (CD-DA) 6. Video CD 7. SVCD (Conforming to IEC62107) 8. CD-R/RW (CD-DA, Video-CD, SVCD, MP3, WMA, JPEG formatted disc) 9. MP3/WMA*1 Compatible compression rate: MP3: between 32 kbps and 320 kbps WMA:
6、 between 48 kbps and 320 kbps 10. JPEG*1 DVD Home Theater Sound System Specification ORDER NO. MD0501005C2 RadioFans.CN 收音机爱 好者资料库 Exif Ver 2.1 JPEG Baseline files Picture resolution: between 320 x 240 and 6144 x 4096 pixels (sub sampling is 4:2:2 or 4:2:0) 11. HighMAT Level 2 (Audio and Image) *1 T
7、he total combined maximum number of recognizable audio and picture contents and groups: 4000 audio and picture contents and 400 groups. Pick up WavelengthCD 785 nm DVD 662 nm Laser powerCLASS 2/CLASS 3A Audio output (Disc) Number of channels5.1ch (FL, FR, C, SL, SR, SW) n Video Section Video System
8、Signal systemPAL625/50, PAL525/60, NTSC Composite video output Output level1 Vp-p (75 ) TerminalPin jack (1 system) Scart jack (1 system) S-video output Y output level1 Vp-p (75 ) C output levelPAL; 0.3 Vp-p (75 ) NTSC; 0.286 Vp-p (75 ) TerminalS terminal (1 system) Scart jack (1 system) Component V
9、ideo Output (480p/480i) Y output level1 Vp-p (75 ) PBoutput level0.7 Vp-p (75 ) PRoutput level0.7 Vp-p (75 ) Terminal 1 Caution for AC Mains Lead 4 2 Use of Active Subwoofer 5 2.1. Checking Main Unit when Active Subwoofer is Used 5 2.2. Checking Main Unit Using Power Jig 6 3 Before Repair and Adjust
10、ment 6 4 SAFETY PRECAUTIONS 6 4.1. GENERAL GUIDELINES 6 5 Handling the Lead Solder 7 5.1. About lead free solder (PbF) 7 6 Protection Circuitry 7 7 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices 8 8 Cautions to Be Taken When Handling Optical Pickup 9 8.1. Ha
11、ndling Optical Pickup 9 Pin jack (Y: green, PB: blue, PR: red) (1 system) RGB video output R output level0.7 Vp-p (75 ) G output level0.7 Vp-p (75 ) B output level0.7 Vp-p (75 ) TerminalScart jack (1 system) n General Power SupplyAC 230-240 V, 50 Hz Power consumption25 W (SA-HT530), 250 W (SB-WA530)
12、 Dimensions (W x H x D)430 x 60 x 348.3 mm Mass2.7 kg (SA-HT530) Operating temperature range+5 C to +35 C Operating humidity range 5 % to 90 % RH (no condensation) Power consumption in standby mode: approx. 0.7 W *2Rating with low cut filter equipped amplifier n System SC-HT530 (EB)Main unit: SA-HT5
13、30 (EB) Satellite speakers: SB-HT530 (EB) Active subwoofer: SB-WA530 (EB) Satellite speakers: SB-HT530 (EB) Front speakers: SB-FS530 (EB) x 2 Surround speakers: SB-FS530 (EB) x 2 Center speaker: SB-PC730 (P-S1) x 1 Note: 1. Specifications are subject to change without notice. Mass and dimensions are
14、 approximate. 2. Total harmonic distortion is measured by the digital spectrum analyzer. 8.2. Cautions to Be Taken During Replacement of Optical Pickup 10 8.3. Grounding for Preventing Electrostatic Destruction 10 9 Precaution of Laser Diode 11 10 Accessories 12 11 Remote Control Reference 13 12 Dis
15、c information 14 13 About HighMAT 18 13.1. What 痴 HighMAT? 18 13.2. Why take advantage of HighMat? 19 13.3. Benefits of HighMat? 19 14 Optical Pickup Self-Diagnosis and Replacement Procedure 22 14.1. Self-diagnosis 22 CONTENTS Page Page 2 SA-HT530EB RadioFans.CN 收音机爱 好者资料库 14.2. Cautions to Be Taken
16、 During Replacement of Optical Pickup and Spindle Motor 23 15 Self-Diagnosis Function 24 15.1. Automatic Displayed Error Codes 24 15.2. Memorized Error Codes 24 15.3. Mode Table 1 25 15.4. DVD/CD Self-Diagnosis Error Code Description 25 15.5. Mode Table 2 26 15.6. Lock Function 28 15.7. Things to Do
17、 After Repair 28 16 Service precautions 29 16.1. Recovery after the player is repaired 29 16.2. DVD Player Firmware Version Upgrade Process 29 16.3. Firmware Version Upgrade Process by Using Recovery Disc 29 17 Disassembly and Main Component Replacement Procedures 31 17.1. Disassembly flow chart 31
18、17.2. P.C.B. Locations 32 17.3. Disassembly of Top Cabinet 33 17.4. Disassembly of Front Panel Unit 33 17.5. Disassembly of Panel P.C.B. Typically the melting point is 50 - 70F (30 - 40C) higher. Please use a high temperature soldering iron. In case of the soldering iron with temperature control, pl
19、ease set it to 700 20F (370 10C). Pb free solder will tend to splash when heated too high (about 1100F/600C). When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the soldering points with the Pb free solder until it melts enough.
20、6 Protection Circuitry The protection circuitry may have operated if either of the following conditions are noticed: No sound is heard when the power is turned on. Sound stops during a performance. The function of this circuitry is to prevent circuitry damage if, for example, the positive and negati
21、ve speaker connection wires are “shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used. If this occurs, follow the procedure outlines below: 1. Turn off the power. 2. Determine the cause of the problem and correct it. 3. Turn on the power
22、 once again after one minute. Note : When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again. 7 SA-HT530EB 7 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) dev
23、ices can be damaged easily by electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduc
24、e the incidence of component damage caused by electro static discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equiped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available dischar
25、ging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equiped with ES devices, place the assembly on a conductive surface such as aluminium foil, to prevent electrostatic charge build up or e
26、xposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder remover device. Some solder removal devices not classified as “anti-static (ESD protected)” can generate electrical charge to damage ES devices. 5. Do not use freon-
27、propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by
28、 conductive foam, aluminium foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Caution Be sure no power is
29、 applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate sta
30、tic electricity (ESD) sufficient to damage an ES device). 8 SA-HT530EB 8 Cautions to Be Taken When Handling Optical Pickup The laser diode used inside the optical pickup could be destroyed due to static electricity (potential difference is caused by electrostatic load discharged from clothes and hum
31、an body). Handle the parts carefully to avoid electrostatic destruction during repair TOC is unreadable or invalid disc is inserted. ODC system F600Unable to obtain control information due to form recovery failure Operation stops because navigation data cannot be obtained due to form recovery system
32、 failure. F601Illegal sector ID requestedOperation stops because access of illegal ID data is requested. F602Unable to obtain LEAD IN due to form recovery failure Unable to read LEAD IN data F603Unable to obtain KEY DET due to form recovery failure Unable to obtain CSS data F610ODC failureNo permiss
33、ion of command issue F611No CRC OK appearing for a certain timeUnable to obtain seek address at CD system F612No CRC OK appearing for a certain timeUnable to obtain ID data at DVD system Disc Code F103Ilegal highlight positionDisc standard is possibly illegal when highlight is displayed. IIC Error F
34、4FFForced initialization failure (Time out) Micro-computer Error F700MBX overflowWhen replying a message to Disc Manager F701Unable to complete a message commandA message is issued before replying to Disc Manager. F702Change in a message commandA message is issued before replying to Disc Manager. F8
35、80Unsuitable task numberWhen a message arrives from not existing task F890A message is sent during AV task transmissionDuring transmission of a message to AV task F891Unable to transmit a message to AV taskWhen transmission of a message to AV task starts F893FROM altered F894EEPROM failure F8A0Unsui
36、table message commandWhen transmission of a message to AV task starts 25 SA-HT530EB 15.5. Mode Table 2 Following modes are available with combinations of the pressed buttons on the player and on the remote controller unit. ItemOperational Condition and Key Function DetailsDisplayTo Exit Mode Jitter
37、displayWhiletheplayeris stopped and no disc is inserted,pressand holddownthe buttonon the player andthenumber button,“5”onthe remote controller unit. Jitter display Measuresanddisplaysjitter. Measurementisrepeatedevery second. Read error counter starts at 0 at the mode setting, and increased by one
38、as data read fails at target block. A small defect is allowed to correct by retry. Any possibility is counted as one increment. Repetitive errors after retry increase by two levels or more. J*1xxx*2_yyy*3_zz*4 *1 : Jitter display mode *2 : Jitter measurement value *3 : Read error counter *4 : Focus
39、driving value Values are shown to one decimal place in the decimal digit.Focus driving value is displayed in the hexadecimal digit. Press the STOP or OPEN button. Errorcode display Whiletheplayeris stopped and no disc is inserted,pressand holddownthe buttonon the player andthenumber button,“0”onthe
40、remote controller unit. Error code display Displays the latest error code stored in EEPROM. DVDnn_F- *nn: Error history *-: Error number Automatically exits the mode after five seconds. Measurementof lasercurrent electricity initialization value Whiletheplayeris stopped and no disc is inserted,press
41、and holddownthe buttonon the player and thebutton on theremotecontroller unit. Measurementoflasercurrent electricity initialization value Memorizes each initialization value of DVD and CD in EEPROM. DO*1_034*2_028*3 *1 : Laser current electricity measurement mode *2 : DVD current electricity value *
42、3 : CD current electricity value Values are shown in the decimal digit. The above example indicates that the current electricity initialization value is 34mA at DVD laser and 28mA at CD laser when laser is turned on. Automatically exits the mode after five seconds. Measurementof DVD laser current el
43、ectricity Whiletheplayeris stopped and no disc is inserted,pressand holddownthe buttonon the player andtheDISPLAY button on the remote controller unit. Measurement of DVD laser current electricity Measures DVD laser current electricity and displays the result together with theinitializationvaluestor
44、edin EEPROM. After measurement, DVD laser is lit till the power is turned off (or goes off when the primary power is turned off). DD*1_034*2_032*3 *1 : DVD laser current electricity measurement mode *2 : Current electricity initialization value stored in EEPROM *3 : Present value of current electric
45、ity Values are shown in the decimal digit. The above example indicates that the current electricity initialization value is 34mA and its present value is 32mA. Automatically exits the mode after five seconds. ADSCinternal RAM display Whiletheplayeris stopped and no disc is inserted,pressand holddown
46、the buttonon the player and the number button “1” or “2” on the remote controller unit. ADSC internal RAM display Reads and displays the RAM value inside ADSC. The address is renewed when the CLEAR key is pressed so that the values at eleven points appear. A*1_0FA*2_6901*3 *1 :ADSC internal RAM disp
47、lay mode *2 : Address *3 : RAM value at displayed address Values are shown in the hexadecimal digit. The above example indicates that ADSC value at the address, 0FAh is 6901h. Press the STOP or OPEN button. Measurementof CD laser current electricity Whiletheplayeris stopped and no disc is inserted,p
48、ressand holddownthe buttonon the player and the number button “3”ontheremote controller unit. MeasurementofCDlasercurrent electricity Measures CD laser current electricity and displays the result together with theinitializationvaluestoredin EEPROM.Aftermeasurement,CD laser is lit till the power is t
49、urned off (or goes off when the primary power is turned off). DC*1_028*2_026*3 *1 : CD laser current electricity measurement mode *2 : Current electricity initialization value stored in EEPROM *3 : Present value of current electricity Values are shown in the decimal digit. The above example indicates the current electricity initialization value is 28mA and its present value is 26mA when laser is turned on. Automatically exits the mode after five seconds. 26 SA-HT530EB ItemOperational Condition and Key Fu
免费区 
