《Yamaha-RX-397-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Yamaha-RX-397-Service-Manual(1) 电路图 维修手册.pdf（41页珍藏版）》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore no
2、t been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that any ser
3、vice required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical capabilities, or establi
4、sh a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
5、 and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by
6、 grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. IMPORTANT NOTICE 100978 SERVICE MANUAL STEREO RECEIVER AMP ADJUSTMENT . . . . .
7、 . . . . . . . . . . . . . . . . . . . . 16 IC DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1718 DISPLAY DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 PIN CONNECTION DIAGRAM . . . . . . . . . . . . . . . . . 20 PRINTED CIRCUIT BOARD . . . . . . . . . . . .
8、 . . . . 2127 BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . . . . . 2931 REMOTE CONTROL RAX16 . . . . . . . . . . . . . . . . . . 33 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3442 I CONTENTS TO SERVIC
9、E PERSONNEL . . . . . . . . . . . . . . . . . . . . 2 IMPEDANCE SELECTOR . . . . . . . . . . . . . . . . . . . . . . 3 FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 REAR PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 REMOTE CONTROL PANEL . . . . . . . .
10、 . . . . . . . . . . . 5 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 67 INTERNAL VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 DISASSEMBLY PROCEDURES . . . . . . . . . . . . . . . . . 8 SELF DIAGNOSIS FUNCTION . . . . . . . . . . . . . . . 915 DPX-1200RX-397
11、 RX-397 2005 YAMAHA CORPORATION. All rights reseved. This manual is copyrighted by YAMAHA and may not be copied or redistributed either in print or electronically without permission. 05.11 RadioFans.CN 收音机爱 好者资料库 2 RX-397 RX-397 I TO SERVICE PERSONNEL 1. Critical Components Information Components ha
12、ving special characteristics are marked Z and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly ins
13、ulated from supply circuits. GMeter impedance should be equivalent to 1500 ohms shunted by 0.15F. AC LEAKAGE TESTER OR EQUIVALENT EQUIPMENT UNDER TEST INSULATING TABLE WALL OUTLET GLeakage current must not exceed 0.5mA. GBe sure to test for leakage with the AC plug in both polarities. WARNING: CHEMI
14、CAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause can
15、cer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux v
16、apor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. About Lead Free Solder The P.C.B.s installed in this unit are soldered using the following solder. “CAUTION” “F251, F252 : FOR CONTINUED PROTECTION AGAINST RISK
17、OF FIRE, REPLACE ONLY WITH SAME TYPE 5A, 125V FUSE.” CAUTION F251, F252 : REPLACE WITH SAME TYPE 5A, 125V FUSE. ATTENTION F251, F252 : UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 5A, 125V. A V SI DE ASI DE B FUNCTI ON P. C. B.Lead Free Solder OPERATI ON P. C. B.Lead Free Solder MAI N P. C. B.Lea
18、d Free Solder Side A Side B SMT REFLOW Process MI FLOW Process Solder Dip Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth)
19、 Caution: 1. As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder. 2. If lead solder must be used, be sure to remove lead free solder from each terminal section of the pa
20、rts to be replaced and from the area around it completely before soldering, or make sure that the lead free solder and lead solder melt together fully. RadioFans.CN 收音机爱 好者资料库 3 RX-397 DPX-1200RX-397 I IMPEDANCE SELECTOR WARNING: Do not change the setting of the IMPEDANCE SELECTOR switch when the un
21、it power is switched on, as doing so may damage the unit. IMPEDANCE SELECTOR I FRONT PANEL RadioFans.CN 收音机爱 好者资料库 4 RX-397 RX-397 I REAR PANELS M U, C models M R model M A model 5 RX-397 DPX-1200RX-397 M G, E models M L model I REMOTE CONTROL PANEL M RAX16 6 RX-397 RX-397 I SPECIFICATIONS AUDIO SEC
22、TION Minimum RMS Output Power (Power Amp. Section) L/R, 20 Hz to 20 kHz, 0.04% THD, 8 ohms . . . . . . .50 W + 50 W Dynamic Power Per Channel (IHF) 8/6/4/2 ohms . . . . . . . . . . . . . . . . . . . . . . . . . .70/77/89/100 W Maximum Power Per Channel (G, E models) 1 kHz, 0.7 % THD, 4 ohms . . . .
23、. . . . . . . . . . . . . . . . . . . . .55 W IEC Power (G, E models) 1 kHz, 0.04% THD, 8 ohms . . . . . . . . . . . . . . . . . . . . . . . .52 W Maximum Power (EIAJ) (R, L moels) 1 kHz, 10% THD, 8 ohms . . . . . . . . . . . . . . . . . . . . . . . . . .85 W Power Band Width L/R, 0.08% THD, 22.5 W,
24、 8 ohms . . . . . . . . . .10 Hz to 50 kHz Damping Factor 20 Hz to 20 kHz, SPEAKER-A, 8 ohms . . . . . . . . .150 or more Input Sensitivity/Input Impedance PHONO MM . . . . . . . . . . . . . . . . . . . . . . . . .2.5 mV/47 k-ohms CD, etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . .150 m
25、V/47 k-ohms Maximum Input Signal PHONO MM, 1kHz, 0.04 % THD . . . . . . . . . . . . . . . . . .115 mV CD, etc., 1kHz, 0.04 % THD . . . . . . . . . . . . . . . . . . . . . . .2.2 V Output Level/Output Impedance REC OUT . . . . . . . . . . . . . . . . . . . . . . . . . .150 mV/1.2 k-ohms Headphone Jac
26、k Rated Output/Output Impedance CD, etc. 1 kHz, 150 mV, 8 ohms, 0.04% THD . . . . . . . . . .0.47 V/330 ohms Frequency Response CD, etc. 20 Hz to 20 kHz . . . . . . . . . . . . . . . . . . . . . .0 0.5 dB CD, etc. PURE DIRECT ON, 10 Hz to 100 kHz . . . . . . . . . . . .0 1.0 dB RIAA Equalization Dev
27、iation PHONO MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 0.5 dB Total Harmonic Distortion (20 Hz to 20 kHz) PHONO MM to REC OUT (3 V) . . . . . . . . . . . . . . . . .0.02 % or less CD, etc. to SP OUT (35 W/8 ohms) . . . . . . . . . .0.02 % or less Signal to Noise Ratio (IHF-
28、A Network) PHONO MM (Input shorted, 5 mV) . . . . . . . . . .82 dB or more CD, etc. (Input shorted, 150mV) . . . . . . . . . . .108 dB or more Residual Noise (IHF-A Network) PURE DIRECT ON . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 V Channel Separation CD, etc. (Input 5.1 k-ohms shor
29、ted) 1 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 dB or more 10 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 dB or more Tone Control Characteristics BASSBoost/Cut (50 Hz) . . . . . . . . . . . . .+10 dB/-10 dB Turnover Frequency . . . . . . . . . . . . . .
30、 . . .350 Hz TREBLEBoost/Cut (20 kHz) . . . . . . . . . . . .+10 dB/-10 dB Turnover Frequency . . . . . . . . . . . . . . . . .3.5 kHz Continuous Loudness Control Attenuation (1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30 dB Gain Tracking Error 0 to -60 dB . . . . . . . . . . .
31、. . . . . . . . . . . . . . . . . . . .2 dB or less GENERAL Power Supply U, C models . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz R model . . . . . . . . . . . . . AC 110/120/220/230-240 V, 50/60 Hz A model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 240 V, 50
32、 Hz G, E models . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V, 50 Hz L model . . . . . . . . . . . . . . . . . . . . AC 220/230-240 V, 50/60 Hz Power Consumption (reference) . . . . . . . . . . . . . . . . . . 130 W Standby Power Consumption . . . . . . . . . . . . . . . . . . . . . 0
33、.1 W Maximum Power Consumption (R moel) 1 kHz, 8 ohms, 10% THD . . . . . . . . . . . . . . . . . . . . . . . 300 W AC Outlet 2 Switched Outlet R model . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 W Max. total U, C, G, E, L models . . . . . . . . . . . . . . . . . . 100 W Max. total 1 S
34、witched Outlet A models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 W Max. Dimensions (W x H x D) . . . . . . . . . . . . . . 435 x 151 x 308 mm (17-1/8 x 5-15/16 x 12-1/8) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.4 kg (16 lbs 5 oz) Finish . . . . . .
35、 . . . . . . . .Black Color (U, C, R, A, G, E, L models) Titanium Color (G, E, L models) Accessories . . . . . . . . . . . . . . . . . . . . . . . .Remote Control x 1 Battery (AAA, R03, UM-4) x 2 Indoor FM Antenna x 1 AM Loop Antenna x 1 * Specifications subject to change without notice. U . USA mod
36、el C . Canadian model R . General model A . Australian model G . European model E . South European model L . Singapore model FM SECTION Tuning Range U, C models . . . . . . . . . . . . . . . . . . . . . . . . .87.5 to 107.9 MHz R, L models . . . . . . . . . . . .87.5 to 108.0/87.50 to 108.00 MHz A,
37、G, E models . . . . . . . . . . . . . . . . . . . . . 87.50 to 108.00 MHz 50 dB Quieting Sensitivity (IHF) 1 kHz 100% MOD. Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.0 V (17.3 dBf) Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 V (39.2 dBf) Usable Sensiti
38、vity (IHF) Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.0 V (11.2 dBf) Selectivity at 400 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 dB Signal to Noise Ratio (IHF) Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39、 . . .76 dB Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 dB Harmonic Distortion (1 kHz) Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.2 % Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40、 . .0.3 % Stereo Separation (1 kHz) . . . . . . . . . . . . . . . . . . . . . . . .45 dB Frequency Response 20 Hz to 15 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . .+0.5/-2.0 dB Antenna Input . . . . . . . . . . . . . . . . . . . . . .75 ohms unbalanced AM SECTION Tuning Range U, C model
41、s . . . . . . . . . . . . . . . . . . . . . . . . . . .530 to 1710 kHz R, L models . . . . . . . . . . . . . . . . .530 to 1710/531 to 1611 kHz A, G, E models . . . . . . . . . . . . . . . . . . . . . . . . 531 to 1611 kHz Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . .300
42、 V/m Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Loop antenna 7 RX-397 DPX-1200RX-397 Unit : mm (inch) DIMENSIONS I INTERNAL VIEW 435 (17-1/8) 151 (5-15/16) 130 (5-1/8)267 (10-1/2)21 (13/16) 18.5 (3/4) 22.5 (7/8) 308 (12-1/8) qw ertyuio!0 !3!2!1 !5!3!4 !9!7!1!2!8!6 qOPER
43、ATION (12) P.C.B. (A, G, E, L models) wMAIN (4) P.C.B. (R, L models) eMAIN (2) P.C.B. rMAIN (3) P.C.B. tMAIN (1) P.C.B. yMAIN (5) P.C.B. uFUNCTION (4) P.C.B. iFUNCTION (1) P.C.B. oFUNCTION (2) P.C.B. !0OPERATION (13) P.C.B. !1OPERATION (10) P.C.B. !2OPERATION (3) P.C.B. !3OPERATION (2) P.C.B. !4OPER
44、ATION (1) P.C.B. !5OPERATION (8) P.C.B. !6OPERATION (5) P.C.B. !7OPERATION (7) P.C.B. !8OPERATION (4) P.C.B. !9OPERATION (9) P.C.B. 8 RX-397 RX-397 I DISASSEMBLY PROCEDURES Remove parts in disassembly order as numbered. Disconnect the power cable from the AC outlet. Fig. 1 1. Removal of Top Cover a.
45、 Remove 4 screws ( q ), 1 screw ( w ) and 4 screws ( e ). (Fig. 1) b. Slide the Top Cover rearward to remove it. (Fig. 1) 2. Removal of Front Panel Unit a. Remove 5 knobs (INPUT, BASS, TREBLE, BALANCE and LOUDNESS). b. Remove 1 screw ( r ) and then remove the Support Top. (Fig. 1) c. Remove 7 screws
46、 ( t ) and then remove the Front Panel Unit. (Fig. 1) 3. Removal of Plate Side Remove 2 push rivets ( y ) and then remove the Plate Side L/R. (Fig. 1) 4. Removal of Sub Chassis Unit a. Remove 2 screws ( u ) and then slide the Sub Chassis Unit forward. (Fig. 1) b. Loosen the harness fixture fixing th
47、e cable. c. Remove connectors CB103, CB401, CB404, CB606 and CB611 and then remove the Sub Chassis Unit. (Fig. 1) q q w e r t t y y u u Knob Knob Top Cover Sub Chassis Unit Plate Side L Plate Side R CB404 CB103 CB606 CB611 CB401 Support Top Front Panel Unit 9 RX-397 DPX-1200RX-397 I SELF DIAGNOSIS F
48、UNCTION This product has a built-in self diagnosis function (DIAG) to facilitate inspection, measurement and determination of a faulty item, if any. There are 8 DIAG menu items, each having sub-menu items. No. DIAG menuSub-menu 1DISPLAY CHECK1. VFD CHECK (Initial display) 2. VFD DISP OFF (All segmen
49、ts OFF) 3. VFD DISP ALL (All segments ON 100%) 4. VFD DIMMER (All segments ON 50%) 5. CHECKED PATTERN (ON in lattice) 2FACTORY PRESET1. PRESET INHI (memory initialization inhibited) 2. PRESET RSRV (memory initialized) 3AD DATA CHECK1. DC/PS (protection) 2. THM L, R 3. REC-OUT (No applied to this model) 4. K0 / K1 (panel key) 4XM STATUS1. XMS1 (No applied to this model) 2. XMS2 (No applied to this model) 5PROTECTION SETTING1. PS_Lo : 2. PS_Hi : 3. DC_Lo : 4. DC_Hi : 5. TEMP : 6PROTECTION HISTORY1. history 1 2. histor
免费区 
