《Panasonic-SAHT535EE-htss-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Panasonic-SAHT535EE-htss-sm 电路图 维修手册.pdf（104页珍藏版）》请在收音机爱好者资料库上搜索。
1、Amplifier Section RMS Output Power: Dolby Digital Mode Front Ch 55 W per channel (6 ), 1 kHz, 10% THD Surround Ch 55 W per channel (6 ), 1 kHz, 10% THD Center Ch 160 W per channel (6 ), 1 kHz, 10% THD Subwoofer Ch 220 W per channel (4 ), 100 Hz, 10% THD Total RMS Dolby Digital Mode Power600 W DIN Ou
2、tput Power: Dolby Digital Mode Front Ch 40 W per channel (6 ), 1 kHz, 1% THD Surround Ch 40 W per channel (6 ), 1 kHz, 1% THD Center Ch 120 W per channel (6 ), 1 kHz, 1% THD Subwoofer Ch 150 W per channel (4 ), 100 Hz, 1% THD Total DIN Dolby Digital Mode Power430 W FM/AM Tuner, Terminals Section Pre
3、set stationFM 15 stations 2005 Matsushita Electric Industrial Co. Ltd. All rightsreserved.Unauthorizedcopyingand distribution is a violation of law. SA-HT535EE Colour (S).Silver Type AM/MW 15 stations Frequency Modulation (FM) Frequency Range 87.50-108.00 MHz (50-kHz step) Sensitivity1.5 V (IHF) S/N
4、 26 dB1.2 V Antenna terminals75 (unbalanced) Amplitude Modulation (AM/MW) Frequency Range522-1629 kHz (9-kHz step) AM Sensitivity S/N 20 dB at 999 kHz560 V/m Phone Jack TerminalStereo, 3.5 mm jack Mic Jack Sensitivity0.7 mV, 1.2 k TerminalMono, 6.3 mm jack (2 systems) Disc Section Disc played 8 cm o
5、r 12 cm 1. DVD (DVD-Video, DVD-Audio, DivX*1,2) 2. DVD-RAM (DVD-VR, JPEG*2, 3, MPEG4*2,4, DivX*1,2) 3. DVD-R (DVD-Video, DivX*1, 2) 4. DVD-RW (DVD-Video, DVD-VR, DivX*1,2) 5. +R/+RW (Video) DVD Home Theater Sound System Specification ORDER NO. MD0508309C3 RadioFans.CN 收音机爱 好者资料库 6. CD, CD-R/RW CD-DA
6、, Video-CD, SVCD*5, MP3*2,6, WMA*2,7, JPEG*2, 3, MPEG*2, 4, DivX*1, 2, HIGHMAT Level 2 (Audio and Image) *1 DivX 3.11, 4.x, 5.x GMC (Global Motion Compensation) is not supported. *2The total combined maximum number of recognizable audio, picture and video contents and groups: 4000 audio, picture and
7、 video contents and 400 groups. *3Exif Ver 2.1 JPEG Baseline files Picture resolution: between 160 X 120 and 6144 X 4096 pixels (Sub sampling is 4:2:2 or 4:2:0) *4MPEG4 data recorded with Panasonic SD multi-cameras or DVD video recorders Conforming to SD VIDEO specifications (ASF standard)/MPEG4 (Si
8、mple Profile) video system/G.726 audio system *5Conforming to IEC62107. *6 MPEG-1 Layer 3, MPEG-2 Layer 3. *7Windows Media Audio Ver.9.0 L3. Not compatible with Multiple Bit Rate (MBR) Pick up WavelengthCD 785 nm DVD 662 nm Laser powerCLASS 2/CLASS 3A Audio output (Disc) Number of channels5.1ch (FL,
9、 FR, C, SL, SR, SW) Video Section Video System Signal systemPAL625/50, PAL525/60, NTSC Composite video output Output level1 Vp-p (75 ) TerminalPin jack (1 system) Scart jack (1 system) S-video output Y output level1 Vp-p (75 ) C output levelPAL; 0.3 Vp-p (75 ) NTSC; 0.286 Vp-p (75 ) TerminalS termin
10、al (1 system) Scart jack (1 system) Component Video Output 1 Use of Active Subwoofer 4 1.1. Checking Main Unit when Active Subwoofer is Used 4 1.2. Checking Main Unit Using Power Jig 5 2 Before Repair and Adjustment (Using Active Subwoofer Unit) 5 3 SAFETY PRECAUTIONS 5 3.1. GENERAL GUIDELINES 5 NTS
11、C: 525 (480) p/525 (480) i, PAL: 625 (576) p/625 (576)i Y output level1 Vp-p (75 ) PBoutput level0.7 Vp-p (75 ) PRoutput level0.7 Vp-p (75 ) Terminal Pin jack (Y: green, PB: blue, PR: red) (1 system) RGB video output R output level0.7 Vp-p (75 ) G output level0.7 Vp-p (75 ) B output level0.7 Vp-p (7
12、5 ) TerminalScart jack (1 system) General Power SupplyAC 230 V, 50 Hz Power consumption25 W (SA-HT535), 250 W (SB-WA535) Dimensions (W x H x D)430 x 60 x 348.3 mm Mass2.7 kg (SA-HT535) Operating temperature range+5 C to +35 C Operating humidity range 5 % to 90 % RH (no condensation) Power consumptio
13、n in standby mode: approx. 0.7 W *8Rating with low cut filter equipped amplifier System System: SC-HT535 (EE) Main unit: SA-HT535 (EE-S) Satellite speaker: SB-HT535 (EG-S) Active subwoofer: SB-WA535 (EE-S) Speakers: SB-HT535 (EG) Front speakers: SB-FS535 (EG-S) Surround speakers: SB-FS536 (EG-S) Cen
14、ter speaker: SB-PC535 (EG-S) Note: 1. Specifications are subject to change without notice. Mass and dimensions are approximate. 2. Total harmonic distortion is measured by the digital spectrum analyzer. 4 Handling the Lead Solder 6 4.1. About lead free solder (PbF) 6 5 Protection Circuitry 6 6 Preve
15、ntion of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices 7 7 Cautions to Be Taken When Handling Optical Pickup 8 7.1. Handling Optical Pickup 8 CONTENTS Page Page 2 SA-HT535EE RadioFans.CN 收音机爱 好者资料库 7.2. Cautions to Be Taken During Replacement of Optical Pickup 9 7.3. Gro
16、unding for Preventing Electrostatic Destruction 9 8 Precaution of Laser Diode 10 9 Accessories 11 10 Remote Control Reference 12 11 Disc information 13 12 About HighMAT 18 12.1. What 痴 HighMAT? 18 12.2. Why take advantage of HighMat? 19 12.3. Benefits of HighMat? 19 13 Optical Pickup Self-Diagnosis
17、and Replacement Procedure 22 13.1. Self-diagnosis 22 13.2. Cautions to Be Taken During Replacement of Optical Pickup and Spindle Motor 23 14 Self-Diagnosis Function 24 14.1. Automatic Displayed Error Codes 24 14.2. Memorized Error Codes 24 14.3. Service Mode Table 1 25 14.4. DVD/CD Self-Diagnosis Er
18、ror Code Description 25 14.5. Mode Table 2 26 14.6. Lock Function 28 14.7. Things to Do After Repair 28 15 Service precautions 29 15.1. Recovery after the player is repaired 29 15.2. DVD Player Firmware Version Upgrade Process 29 15.3. Firmware Version Upgrade Process by Using Recovery Disc 29 16 Di
19、sassembly and Main Component Replacement Procedures 31 16.1. Disassembly flow chart 31 16.2. P.C.B. Locations 32 16.3. Disassembly of Top Cabinet 33 16.4. Disassembly of Front Panel Unit 33 16.5. Disassembly of Panel P.C.B., Headphone P.C.B. Typically the melting point is 50 - 70F (30 - 40C) higher.
20、 Please use a high temperature soldering iron. In case of the soldering iron with temperature control, please set it to 700 20F (370 10C). Pb free solder will tend to splash when heated too high (about 1100F/600C). When soldering or unsoldering, please completely remove all of the solder on the pins
21、 or solder area, and be sure to heat the soldering points with the Pb free solder until it melts enough. 5 Protection Circuitry The protection circuitry may have operated if either of the following conditions are noticed: No sound is heard when the power is turned on. Sound stops during a performanc
22、e. The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are “shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used. If this occurs, follow the procedure outlines
23、 below: 1. Turn off the power. 2. Determine the cause of the problem and correct it. 3. Turn on the power once again after one minute. Note : When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again. 6 SA-HT535EE 6 Prevention of Electr
24、o Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effe
25、ct transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equiped assembly, drain off any ESD on yo
26、ur body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equiped with ES devices, place t
27、he assembly on a conductive surface such as aluminium foil, to prevent electrostatic charge build up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder remover device. Some solder removal devices not classified a
28、s “anti-static (ESD protected)” can generate electrical charge to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are r
29、eady to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminium foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective materia
30、l to the chassis or circuit assembly into which the device will be installed. Caution Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the br
31、ushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device). 7 SA-HT535EE 7 Cautions to Be Taken When Handling Optical Pickup The laser diode used inside the optical pickup could be destroyed due to
32、 static electricity (potential difference is caused by electrostatic load discharged from clothes and human body). Handle the parts carefully to avoid electrostatic destruction during repair TOC is unreadable or invalid disc is inserted. ODC system F600Unable to obtain control information due to for
33、m recovery failure Operation stops because navigation data cannot be obtained due to form recovery system failure. F601Illegal sector ID requestedOperation stops because access of illegal ID data is requested. F602Unable to obtain LEAD IN due to form recovery failure Unable to read LEAD IN data F603
34、Unable to obtain KEY DET due to form recovery failure Unable to obtain CSS data F610ODC failureNo permission of command issue F611No CRC OK appearing for a certain timeUnable to obtain seek address at CD system F612No CRC OK appearing for a certain timeUnable to obtain ID data at DVD system Disc Cod
35、e F103Ilegal highlight positionDisc standard is possibly illegal when highlight is displayed. IIC Error F4FFForced initialization failure (Time out) Micro-computer Error F700MBX overflowWhen replying a message to Disc Manager F701Unable to complete a message commandA message is issued before replyin
36、g to Disc Manager. F702Change in a message commandA message is issued before replying to Disc Manager. F880Unsuitable task numberWhen a message arrives from not existing task F890A message is sent during AV task transmissionDuring transmission of a message to AV task F891Unable to transmit a message
37、 to AV taskWhen transmission of a message to AV task starts F893FROM altered F894EEPROM failure F8A0Unsuitable message commandWhen transmission of a message to AV task starts 25 SA-HT535EE 14.5. Mode Table 2 Following modes are available with combinations of the pressed buttons on the player and on
38、the remote controller unit. ItemOperational Condition and Key Function DetailsDisplayTo Exit Mode Jitter displayWhiletheplayeris stopped and no disc is inserted,pressand holddownthe button on the player andthenumber button,“5”onthe remote controller unit. Press“FLDISPLAY” buttononremote control for
39、next page. Jitter display Measuresanddisplaysjitter. Measurementisrepeatedevery second. Read error counter starts at 0 at the mode setting, and increased by one as data read fails at target block. A small defect is allowed to correct by retry. Any possibility is counted as one increment. Repetitive
40、errors after retry increase by two levels or more. J*1_123*2_/ _456*3_AB*4_ display1/display2 *1 : Jitter display mode *2 : Jitter measurement value *3 : Read error counter *4 : Focus driving value Values are shown to one decimal place in the decimal digit.Focus driving value is displayed in the hex
41、adecimal digit. PresstheSTOP button. Errorcode display Whiletheplayeris stopped and no disc is inserted,pressand holddownthe button on the player andthenumber button,“0”onthe remote controller unit. Error code display Displays the latest error code stored in EEPROM. DVDnn_F- *nn: Error history *-: E
42、rror number Automatically exits the mode after five seconds. Measurementof lasercurrent electricity initialization value Whiletheplayeris stopped and no disc is inserted,pressand holddownthe button on the player and thebutton on theremotecontroller unit. Press“FLDISPLAY” buttononremote control for n
43、ext page. Measurementoflasercurrent electricity initialization value Memorizes each initialization value of DVD and CD in EEPROM. _LDO*1_/ 123*2_456*3_ display1/ display2 *1 : Laser current electricity measurement mode *2 : DVD current electricity value *3 : CD current electricity value Values are s
44、hown in the decimal digit. The above example indicates that the current electricity initialization value is 34mA at DVD laser and 28mA at CD laser when laser is turned on. Automatically exits the mode after five seconds. Measurementof DVD laser current electricity Whiletheplayeris stopped and no dis
45、c is inserted,pressand holddownthe button on the player andtheDISPLAY button on the remote controller unit. Press“FLDISPLAY” buttononremote control for next page. Measurement of DVD laser current electricity Measures DVD laser current electricity and displays the result together with theinitializati
46、onvaluestoredin EEPROM. After measurement, DVD laser is lit till the power is turned off (or goes off when the primary power is turned off). _LDD*1_/ 123*2_456*3_ display1/display2 *1 : DVD laser current electricity measurement mode *2 : Current electricity initialization value stored in EEPROM *3 :
47、 Present value of current electricity Values are shown in the decimal digit. The above example indicates that the current electricity initialization value is 34mA and its present value is 32mA. Automatically exits the mode after five seconds. ADSCinternal RAM display Whiletheplayeris stopped and no
48、disc is inserted,pressand holddownthe button on the player and the number button “1” or “2” on the remote controller unit. ADSC internal RAM display Reads and displays the RAM value inside ADSC. The address is renewed when the CLEAR key is pressed so that the values at eleven points appear. A*1_0FA*
49、2_6901*3 *1 :ADSC internal RAM display mode *2 : Address *3 : RAM value at displayed address Values are shown in the hexadecimal digit. The above example indicates that ADSC value at the address, 0FAh is 6901h. Press the STOP or OPEN button. Measurementof CD laser current electricity Whiletheplayeris stopped and no disc is inserted,pressand holddownthe button on the player and the number button “3”ontheremote controller unit. Press“FLDISPLAY” buttononremote control for next page. MeasurementofCD
免费区 
