Yamaha-S-03-Service-Manual 电路图 维修手册.pdf

《Yamaha-S-03-Service-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Yamaha-S-03-Service-Manual 电路图 维修手册.pdf（67页珍藏版）》请在收音机爱好者资料库上搜索。

1、 1.494K-479 K Printed in Japan 01.0220010301-69800 SERVICE MANUAL SY 011550 MUSIC SYNTHESIZER HAMAMATSU, JAPAN CONTENTS SPECIFICATIONS. 3/4 BLOCK DIAGRAM. 5 PANEL LAYOUT. 6 CIRCUIT BOARD LAYOUT. 8 WIRING. 9 DISASSEMBLY PROCEDURE. 10 LSI PIN DESCRIPTION. 15 IC BLOCK DIAGRAM. 17 CIRCUIT BOARDS. 19 TES

2、T PROGRAM. 28/33 FACTORY SET. 39 DISPLAY MESSAGES. 40 MIDI IMPLEMENTATION CHART . 41 PARTS LIST OVERALL CIRCUIT DAIGRAM This document is printed on chlorine free (ECF) paper with soy ink. RadioFans.CN 收音机爱 好者资料库 S03 2 2 2 IMPOR TANT NOTICE This manual has been provided for the use of authorized Yama

3、ha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under- stood by the users, and have therefore not been restated. WARNING :Failure to follow appropriate service and safet

4、y procedures when servicing this product may result in per- sonal injury, destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or t

5、he appointed service representative. IMPORTANT :This presentation or sale of this manual to any individual or firm does not constitute authorization certifi- cation, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form. The data provided is be

6、lived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to change without notice or ob

7、ligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING :Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus in the unit (heavy gaug

8、e black wires connect to this bus.) IMPORTANT :Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit. WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic

9、and/or plastic (Where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR

10、MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before

11、handling food. WARNING Components having special characteristics are marked and must be replaced with parts having specification equal to those originally installed. LITHIUM BA TTERY HANDLING This product uses a lithium battery for memory back-up. WARNING :Lithium batteries are dangerous because the

12、y can be exploded by improper handling. Observe the following pre- cautions when handling or replacing lithium batteries. Leave lithium battery replacement to qualified service personnel. Always replace with batteries of the same type. When installing on the PC board by soldering, solder using the c

13、onnection terminals provided on the battery cells. Never solder directly to the cells. Perform the soldering as quickly as possible. Never reverse the battery polarities when installing. Do not short the batteries. Do not attempt to recharge these batteries. Do not disasemble the batteries. Never he

14、at batteries or throw them into fire. ADVARSEL! Lithiumbatteri-Eksplosionsfare ved fejlagtig handtering. Udskiftning ma kun ske med batteri af samme fabrikat og type. lever det brugte batteri tilbage til leverandren. VARNING Explosionsfara vid felaktigt batteribyte. Anvand samma batterityp eller en

15、ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvant batteri enligt fabrikantens instruktion. VAROITUS Paristo voi rajahtaa, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiiin. Havita kaytetty paristo valmistajan ohjeiden mukais

16、esti. The following information complies with Dutch official Gazette 1995. 45; ESSENTIALS OF ORDER ON THE COLLECTION OF BATTERIES. Please refer to the diassembly procedure for the removal of Back-up Battery. Leest u voor het verwijderen van de backup batterij deze beschrijving. RadioFans.CN 收音机爱 好者资

17、料库 S03 3 SPECIFICATIONS KEYBOARD61 keys with Initial Touch TONE GENERATORAWM2 POLYPHONY64 notes MULTI TIMBRE16 VOICE Normal VoicePreset128 User128 XG480 Drum VoiceUser2 XG20 (including 8 Original Voices) MULTIUser32 EFFECT Reverb11 Chorus11 Variation42 CONTROLSSTANDBY/ON, HOST SELECT, VOLUME, Pitch

18、Bend, Modulation, MULTI, VOICE, DEMO, UTILITY, MIDI, EDIT/COMPARE, JOB, STORE, EXIT, /, / , PART (ELEMENT/KEY) /+, MUTE, OCTAVE UP/ DOWN, INC/YES, DEC/NO, PRESET, USER, XG/GM, CATEGORY SEARCH, Numeric Keypad, ENTER CONNECTORS memory cannot be backed up. Store the necessary data to a MIDI data storag

19、e device such as Yamaha MIDI Data Filer MDF3, and have the battery changed. DISPLAY MESSAGES S03 41 TransmittedFunction.RecognizedRemarks Basic Channel Note Number : True voice Velocity After Touch Pitch Bend Control Change Prog Change : True # System Exclusive Common : Song Pos. : Song Sel. : Tune

20、System : Clock Real Time : Commands : All Sound Off Aux : Reset All Cntrls : Local ON/OFF Mes- : All Notes OFF sages: Active Sense : Reset Notes: Mode Default Changed Note ON Note OFF Keys Chs 0,32 1,5,7,10,11 6,38 64-67 71-74 84 91,93,94 96-97 98-99 100-101 1-31,33-95 1 - 16 1 - 16 9nH,v=1-127 9nH,

21、v=0 *3 0 - 127 * *1 receive if switch is on. *2 m is always treated as 1 regardless of its value. *3 though the keyboard itself has no after touch, after touch data can be transmitted from MW and FC when after touch is assigned to the controllers. 3 * 0 - 127 * Mode 1 : OMNI ON , POLY Mode 2 : OMNI

22、ON ,MONO Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF,MONO 1 - 16 1 - 16 9nH,v=1-127 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 (120,126,127) (121) (123-125) 3 1 - 4(m=1) *2 0 - 127 0 - 127 0-24 semi *1 : Yes : No Default Messages Altered YAMAHA Music Synthesizer Date :27-DEC-2000 Model S03 MIDI Implementa

23、tion ChartVersion : 1.0 Memorized Memorized Bank Select Data Entry Sound Controller Portamento Cntrl Effect Depth RPN Inc,Dec NRPN LSB,MSB RPN LSB,MSB Assignable Cntrl 0 - 127 0 - 127 41 S03 42 1. Channel messages 1.1Note on/note off These messages convey keyboard performance data. Range of note num

24、bers received = 0 (C-2).60 (C3).127 (G8) Velocity range = 1.127 (Velocity is received only for note-on) When the Multi Part parameter Rcv NOTE MESSAGE = OFF, that part will not receive these messages. For a drum part*, key-off is not received if the DrumSetup parameter Rcv NOTE OFF = OFF. For a drum

25、 part, key-on is not received if the DrumSetup parameter Rcv NOTE ON = OFF. * Drum Part indicates that the Multi Part parameter PART MODE is set to DRUM, DRUMS1, DRUMS2. 1.2 Control changes These messages control volume or pan etc. Their functions are differentiated by the control number (Ctrl#). If

26、 the Multi Part parameter Rcv CONTROL CHANGE = OFF, that part will not receive control changes. 1.2.1 Bank Select This message selects the voice bank. Control#ParameterData Range 0Bank Select MSB0, 63, 64, 126, 127 (Normal voice, Native voice, SFX voice, SFX kit, Drum kit) 32Bank Select LSB0.127 The

27、 Bank Select data will be processed only after a Program Change is received, and then voice bank will change at that time. If you wish to change the voice bank as well as the voice, you must transmit Bank Select and Program Change messages as a set, in the order of Bank Select MSB, LSB, and Program

28、Change. Not received when Receive Bank Select in Native System Parameters is set to off. 1.2.2 Modulation This message is used primarily to control the depth of vibrato, but the depth of the following 7 types of effect can be controlled. The effect of this message can be changed by the following par

29、ameters. Multi Part Parameter 1. MW PITCH CONTROL 2. MW FILTER CONTROL 3. MW AMPLITUDE CONTROL 4. MW LFO PMOD DEPTH 5. MW LFO FMOD DEPTH 6. MW LFO AMOD DEPTH Effect1 Parameter 7. MW VARIATION CONTROL DEPTH (Valid when Variation Effect is assigned to a part as Insertion) Control#ParameterData Range 1

30、Modulation0.127 If the Multi Part parameter Rcv MODULATION = OFF, that part will not receive Modulation. If the receive channel is a drum part, effects 5 and 6 will not apply. 1.2.3 Portamento Time This message controls the degree of Portamento (refer to 1.2.9). Control#ParameterData Range 5Portamen

31、to Time0.127 When Portamento (control number 065) is ON, this regulates the speed of the pitch change. A value of 0 is the shortest portamento time, and 127 is the longest portamento time. If the receive channel is a drum part, Portamento Time is not received. 1.2.4 Data Entry This message sets the

32、value of the parameter which was specified by RPN MSB/LSB (see 1.2.22) and NRPN MSB/LSB (see 1.2.21). Control#ParameterData Range 6Data Entry MSB0.127 38Data Entry LSB0.127 1.2.5 Main Volume This message controls the volume of each part. This is used to adjust the volume balance between parts. Contr

33、ol#ParameterData Range 7Main Volume0.127 When the Multi Part parameter Rcv VOLUME = OFF, that part will not receive Main Volume. With a value of 0 there will be no sound, and a value of 127 will be the maximum volume. 1.2.6 Panpot This message control the panning (stereo location) of each part. Cont

34、rol#ParameterData Range 10Pan0.64.127 When the Multi Part parameter Rcv PAN = OFF, that part will not receive Panpot. 0 is left, 64 is center, and 127 is right. 1.2.7 Expression This message controls expression (dynamics within a musical line) for each part. It is used to create volume changes durin

35、g a song. Control#ParameterData Range 11Expression0.127 If the Multi Part parameter Rcv EXPRESSION = OFF, that part will not receive Expression. 1.2.8 Hold1 This message controls sustain pedal on/off. Control#ParameterData Range 64Hold10.63,64.127 (OFF, ON) When this is ON, currently-sounding notes

36、will continue to sound even if note-off messages are received. If the Multi Part parameter Rcv HOLD1 = OFF, that part will not receive Hold1. 1.2.9 Portamento This message controls portamento on/off. Control#ParameterData Range 65Portamento0.63,64.127 (OFF, ON) When this is ON, the pitch will change

37、 smoothly between notes. The time over which the pitch changes is adjusted by Portamento Time (see 1.2.3). Also, when the Multi Part parameter MONO/POLY MODE = MONO, the tone will also change smoothly (legato) if Portamento = ON. If any of the following Multi Part parameter settings apply, that part

38、 will not receive Portamento. Rcv PORTAMENTO = OFF PART MODE=DRUM, DRUMS1, 2 1.2.10 Sostenuto This message controls sostenuto pedal on/off. Control#ParameterData Range 66Sostenuto0.63,64.127 (OFF, ON) If sostenuto is turned on while a note is sounding, that note will be sustained until sostenuto is

39、turned OFF. Sostenuto for the specified part is not received when Rcv SOSTENUTO of the part in Multi Part Parameters is set to off. 1.2.11 Soft Pedal This message controls soft pedal on/off. Control#ParameterData Range 67Soft Pedal0.63,64.127 (OFF, ON) The sound will become mellower when Soft Pedal

40、is ON. If any of the following Multi Part parameter settings apply, that part will not receive the Soft Pedal. Rcv SOFT PEDAL=OFF PART MODE=DRUM, DRUMS1, 2 1.2.12 Harmonic Content This message adjusts the resonance of the filter that is specified for the sound. Control#ParameterData Range 71Harmonic

41、 Content0.64.127 (-64.0.+63) Since this is a relative change parameter, it specifies a boost or cut relative to 64. Higher values will produce a more distinctive sound. For some sounds, the effective range may be less than the possible range of settings. 1.2.13 Release Time This message adjusts the

42、EG release time that was specified by the sound data. Control#ParameterData Range 72Release Time0.64.127 (-64.0.+63) Since this is a relative change parameter, it specifies an increase or decrease relative to 64. Increasing this value will lengthen the release that follows a note-off. 1.2.14 Attack

43、Time This message adjusts the EG attack time that was specified by the sound data. Control#ParameterData Range 73Attack Time0.64.127 (-64.0.+63) Since this a relative change parameter, it specifies an increase or decrease relative to 64. Increasing this value will make the attack more gradual, and d

44、ecreasing this value will make the attack sharper. 1.2.15 Brightness This message adjusts the cutoff frequency of the low pass filter specified by the sound data. Control#ParameterData Range 74Brightness0.64.127 (-64.0.+63) Since this is a relative change parameter, it specifies an increase or decre

45、ase relative to 64. Lower values will produce a more mellow sound. For some sounds, the effective range may be less than the possible range of settings. MIDI DATA FORMAT S03 43 1.2.16 Portamento Control This message specifies the portamento source key number (the key number at which portamento will

46、begin). Data of 0.127 specifies the portamento source key. When Portamento Control is received, the currently-sounding pitch will change at a Portamento Time of 0 to the key of the next-received note-on of the same channel. Control#ParameterData Range 84Portamento Control0.127 (C-2.G8) This is recei

47、ved even if Rcv PORTAMENTO = OFF. 1.2.17 Effect1 Depth (Reverb Send Level) This message specifies the send level for the reverb effect. Control#ParameterData Range 91Effect1 Depth0.127 Increasing this value will produce a richer reverb. The effect of the value will depend on the state of the reverb effect. 1.2.18 Effect3 Depth (Chorus Send Level) This message specifies the send level for the chorus effect. Control#ParameterDa