Denon-AVC4310-avr-sm 电路图 维修手册.pdf

《Denon-AVC4310-avr-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Denon-AVC4310-avr-sm 电路图 维修手册.pdf（211页珍藏版）》请在收音机爱好者资料库上搜索。

1、D&M Holdings lnc. e SERVICE MANUAL AV SURROUND RECEIVER AV SURROUND AMPLIFIER MODELJPEUECE2EKE2AE1CEUT AVR-4310CI ? AVR-4310 ? ? MODELJPEUECE2EKE2AE1CEUT AVC-4310 ? ? s d Ver. 6 For purposes of improvement, specifications and design are subject to change without notice. Please use this service manua

2、l with referring to the operating instructions without fail. Some illustrations using in this service manual are slightly different from the actual set. S0025-1V06DM/DG0912 Please refer to the MODIFICATION NOTICE. RadioFans.CN 收音机爱 好者资料库 2 AVR-4310CI/AVR-4310/AVC-4310 Please heed the points listed b

3、elow during servicing and inspection. Heed the cautions! Spots requiring particular attention when servicing, such as the cabinet, parts, chassis, etc., have cautions indicated on labels or seals. Be sure to heed these cautions and the cautions indicated in the handling instructions. Caution concern

4、ing electric shock! (1) An AC voltage is impressed on this set, so touching in- ternal metal parts when the set is energized could cause electric shock. Take care to avoid electric shock, by for example using an isolating transformer and gloves when servicing while the set is energized, un- plugging

5、 the power cord when replacing parts, etc. (2)There are high voltage parts inside. Handle with extra care when the set is energized. Caution concerning disassembly and assembly! Though great care is taken when manufacturing parts from sheet metal, there may in some rare cases be burrs on the edges o

6、f parts which could cause injury if fingers are moved across them. Use gloves to protect your hands. Only use designated parts! The sets parts have specific safety properties (fire resis- tance, voltage resistance, etc.). For replacement parts, be sure to use parts which have the same properties. In

7、 par- ticular, for the important safety parts that are marked z on wiring diagrams and parts lists, be sure to use the desig- nated parts. Be sure to mount parts and arrange the wires as they were originally! For safety reasons, some parts use tape, tubes or other in- sulating materials, and some pa

8、rts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wires inside and clamps are used to keep wires away from heating and high voltage parts, so be sure to set everything back as it was originally. Inspect for safety after servicing! Check tha

9、t all screws, parts and wires removed or discon- nected for servicing have been put back in their original po- sitions, inspect that no parts around the area that has been serviced have been negatively affected, conduct an insu- lation check on the external metal connectors and between the blades of

10、 the power plug, and otherwise check that safety is ensured. (Insulation check procedure) Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and turn the power switch on. Us- ing a 500V insulation resistance tester, check that the in- sulation resistance between the te

11、rminals of the power plug and the externally exposed metal parts (antenna ter- minal, headphones terminal, microphone terminal, input terminal, etc.) is 1M or greater. If it is less, the set must be inspected and repaired. Concerning important safety parts Many of the electric and structural parts u

12、sed in the set have special safety properties. In most cases these prop- erties are difficult to distinguish by sight, and using re- placement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety performance will be preserved. Parts with safety pro

13、perties are indicated as shown below on the wiring dia- grams and parts lists is this service manual. Be sure to re- place them with parts with the designated part number. (1) Schematic diagrams . Indicated by the z mark. (2) Parts lists . Indicated by the z mark. Using parts other than the designat

14、ed parts could result in electric shock, fires or other dangerous situations. SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1)

15、 a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. CAUTION CAUTION RadioFans.CN 收音机爱 好者资料库 3 AVR-4310CI/AVR-4310/AVC-4310 D

16、IMENSION AVR-4310CI/AVR-4310/AVC-4310 344 434 155 15.5 170.5 20.7 244.5 372.8 20.5 414 54.7 RadioFans.CN 收音机爱 好者资料库 4 AVR-4310CI/AVR-4310/AVC-4310 WIRE ARRANGEMENT If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly as they were origi

17、nally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. Wire arrangement viewed from the top Front Panel side Back Panel side 5 AVR-4310CI/AVR-4310/AVC-4310 CAUTION IN SERVICING Before the Digital P.W.B. are replaced If you cannot specify the cause of

18、the digital PWB defect, carry out Initializing Update to latest firmware. The defect may be cleared. See the following for the method of initializing the com. Initializing AV SURROUND RECEIVER AV SURROUND RECEIVER initialization should be performed when the com, peripheral parts of com, and Digital

19、P.W.B. are replaced. 1. Switch off the unit. 2. Hold the following STANDARD button and DSP SIMULATION button, and switch on the unit. 3. Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 buttons and the microprocessor will be initialize

20、d. Note:If step 3 does not work, start over from step 1. All user settings will be lost and this factory setting will be recovered when this initialization mode. So make sure to memorize your setting for restoring after the initialization. JIG to use for servicing When you repair the printing board,

21、 you can use the following JIG. Please order to Denon Official Service Distributor in your region if necessary. Extention cable kit 00D SPK- 561 EXTENSION UNIT KIT : 1 Set 00D SPK- 562 TUCP CONN. JOINT KIT : 1 Set Extention cable for Idling Current Parts Number for Extension Cables and Quantity of U

22、nit. How to use and Adjust Idle Current. 1. The thin and hard plate (ex. Ruler) is fixed with the tape behind the cable. 2. The voltmeter is connected with the other side of the extension cable. 3. Refer to ADJUSTMENT(Idling Current). Parts NumberParts NameQty / unitRemarks 612050082004D6P 250mm NH1

23、L=250mm 6P NH Cable 612050083007D8P 250mm NH1L=250mm 8P NH Cable 1,22,3 6 AVR-4310CI/AVR-4310/AVC-4310 DISASSEMBLY Disassemble in order of the arrow of the figure of following flow. In the case of the re-assembling, assemble it in order of the reverse of the following flow. In the case of the re-ass

24、embling, observe attention of assembling it. TOP COVER BACK PANEL UNIT ASSYFRONT PANEL UNIT ASSY Refer to DISASSEMBLYREG UNITRefer to DISASSEMBLY 2. BACKPANEL UNIT ASSYRefer to DISASSEMBLY1.FRONT PANEL UNIT ASSY 5. REG UNITP.SW UNIT and EXPLODED VIEW (Ref. No. of EXPLODED VIEW : A-8) DIGITAL UNIT AS

25、SYREG UNIT FRONT HDMI UNIT Refer to DISASSEMBLY (Ref. No. of EXPLODED VIEW : B-4) (Ref. No. of EXPLODED VIEW : E-4) 3. DIGITAL UNIT ASSYREG CONNECT-1 UNITFRONT USB UNIT and EXPLODED VIEW (Ref. No. of EXPLODED VIEW : A-15) (Ref. No. of EXPLODED VIEW : E-3) DIGITAL UNIT CONNECT UNIT-2MIC UNIT (Ref. No

26、. of EXPLODED VIEW : G) (Ref. No. of EXPLODED VIEW : D-4) (Ref. No. of EXPLODED VIEW : A-9) FRONT IN UNIT (Ref. No. of EXPLODED VIEW : A-10) A.VIDEO UNIT, AUDIO UNIT AMP UNITVR CONNECT UNIT and RADIATOR UNIT ASSYRefer to DISASSEMBLY (Ref. No. of EXPLODED VIEW : A-5) Refer to DISASSEMBLY6. AMP UNITVO

27、LUME UNIT 4. A.VIDEO UNIT, AUDIO UNITand EXPLODED VIEW (Ref. No. of EXPLODED VIEW : A-4) and RADIATOR UNIT ASSYAMP UNITFUNC CONNECT UNIT and EXPLODED VIEW (Ref. No. of EXPLODED VIEW : D-1) (Ref. No. of EXPLODED VIEW : A-7) A.VIDEO UNITFUNC UNIT (Ref. No. of EXPLODED VIEW : E-1) (Ref. No. of EXPLODED

28、 VIEW : A-6) AUDIO UNITP.AMP JOINT UNITFLD UNIT (Ref. No. of EXPLODED VIEW : E-2)Refer to DISASSEMBLY (Ref. No. of EXPLODED VIEW : A-1) MAIN CPU UNIT7. P.AMP JOINT UNIT (Ref. No. of EXPLODED VIEW : F)and EXPLODED VIEW REMOTE/IPOD UNITP.AMP JOINT UNIT (Ref. No. of EXPLODED VIEW : B-5) (Ref. No. of EX

29、PLODED VIEW : D-2) 232C UNIT (Ref. No. of EXPLODED VIEW : B-6) P.AMP UNIT Refer to DISASSEMBLY 9.P.AMP UNIT and EXPLODED VIEW P.AMP UNIT (Ref. No. of EXPLODED VIEW : D-17) 7 AVR-4310CI/AVR-4310/AVC-4310 About the photos used for descriptions in the “DISASSEMBLY” section. The direction from which the

30、 photographs used herein were photographed is indicated at Direction of photograph: * at the left of the respective photographs. Refer to the table below for a description of the direction in which the photos were taken. Photographs for which no direction is indicated were taken from above the produ

31、ct. 1. FRONT PANEL UNIT ASSY (1) Remove the screws. (2) Cut the wire clampers then disconnect the connector wires. Front side Direction of photograph: B Direction of photograph: DDirection of photograph: C Direction of photograph: A The viewpoint of each photograph (Photografy direction) View from a

32、bove Proceeding:TOP COVER FRONT PANEL UNIT ASSY View from bottom CX021 CY062 Direction of photograph: D cut cut cut 8 AVR-4310CI/AVR-4310/AVC-4310 (3) Remove the FFC cover and acetate tapes. Disconnect the FFC Cables. (4) Remove the screws. Attention of assembling When mounting the FRONT PANEL ASSY

33、on the CHASSIS, do so with the DOOR open so as to prevent breaking the EARTH PLATE(DOOR). If the FRONT PANEL ASSY is mounted on the chassis with the DOOR closed, the EARTH PLATE(DOOR) will hit the CHASSIS and break. Acetate tape FFC Cover FFC Cable Direction of photograph: C FFC Cable ? Please refer

34、 to EXPLODED VIEW for the disassembly method of each P.W.B included in FRONT PANEL ASSY. DOOR open DOOR closed (EARTH PLATE (DOOR) will be broken.) EARTH PLATE (DOOR) DOOR DOOR EARTH PLATE (DOOR) Direction of photograph: A Direction of photograph: A 9 AVR-4310CI/AVR-4310/AVC-4310 2. BACK PANEL UNIT

35、ASSY (1) Remove the Sheets, then remove the screws. (2) Remove the screws. (3) Disconnect the connector wires and FFC Cable, then remove the screws. Proceeding:TOP COVER BACK PANEL UNIT ASSY Sheets View from bottom ? ? Direction of photograph: A CY153 CY101 CX055 CX074 FFC Cable CY052 10 AVR-4310CI/

36、AVR-4310/AVC-4310 (4) Remove the FFC cover, PWB HOLDER and acetate tapes. Cut the wire clamper, then disconnect the connector wire and FFC Cable. (5) Cut the wire clamper, then disconnect the connector wire. FFC Cable CX068 PWB HOLDER Direction of photograph: C cut Acetate tapeAcetate tapeFFC Cover

37、v Direction of photograph: D BACK PANEL UNIT ASSY CX091 cut 11 AVR-4310CI/AVR-4310/AVC-4310 3. DIGITAL UNIT ASSY (1) Remove the alminium tape, then cut the wire clampers. Disconnect the connector wire, FFC Cables, and board to board. (2) Remove the screws. Proceeding:TOP COVER BACK PANEL UNIT ASSY D

38、IGITAL UNIT ASSY FFC Cable FFC Cable FFC CablecutcutMAIN CPU UNIT DIGTAL UNIT ASSY Board to board CX058 CX124 CX047 CY061Alminium Tape CY124 ? Direction of photograph: A 12 AVR-4310CI/AVR-4310/AVC-4310 4. A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY (1) Disconnect the board to board. (2) Disconne

39、ct the connector wires. (3) Remove the screws. Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY v Direction of photograph: C MAIN CPU UNIT CX073CX192 Direction of photograph: A A.VIDEO UNIT AUDIO UNIT RADIATOR UNIT ASSY 13 AVR-4310CI/AVR-431

40、0/AVC-4310 5. REG UNIT (1) Disconnect the board to board and connector wires. (2) Disconnect the connector wires, then remove the screws. 6. AMP UNIT (1) Disconnect the VH connector and conector. Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT A

41、SSY REG UNIT Board to board Direction of photograph: A CX231CX092 v ? ? Direction of photograph: A Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY REG UNIT AMP UNIT CX851CX891 CX876 CX874 CX871 CX873 CX872 CX875 CX877 View from bottom 14 AV

42、R-4310CI/AVR-4310/AVC-4310 7. P.AMP JOINT UNIT (1) Disconnect the connector. 8. P.AMP UNIT (1) Remove the screws. Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY REG UNIT AMP UNIT P.AMP JOINT UNIT CX803CX805 CX806CX811CX812CX807 CX804 Direc

43、tion of photograph: A Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY REG UNIT AMP UNIT P.AMP JOINT UNIT P.AMP UNIT Direction of photograph: B 15 AVR-4310CI/AVR-4310/AVC-4310 SPECIAL MODE Special mode setting button Press the ON/OFF button

44、to turn on while pressing both buttons A and B at the same time. *1 : About RS-232C communications RS-232C communications are not possible when is displayed on the FL display. Press and hold in the STATUS and buttons for over 3 seconds with the power turned on to turn the display off. RS-232C commun

45、ications are now enabled. ModeButton AButton Bcontents Version display (com/DSP Error Display) STATUSRETURN Serial No. and firmware versions such as Main, Sub, DSP are displayed in the FL manager. Errors are displayed when they occur. (Refer to 16 page.) Displaying the protection history modeSTATUSM

46、ENU Displaying the protection history (Refer to 18 page.) Initialization mode (Remove settings for Installer Setup.) STANDARD DSP SIMULATION Backup data initialization is carried out. (Remove settings for Installer Setup.) Initialization mode (Includes settings for Installer Setup) CURSOR UP CURSOR

47、DOWN Backup data initialization is carried out. (Includes settings for Installer Setup) Mode for switching tuner frequency stepSTANDARD DIRECT/ STEREO -E2 model only- Change tuner frequency step to FM:200kHz/AM:10kHzSTEP. g Mode for preventing remote control acceptance STATUSENTER Operations using r

48、emote control are rejected. (Mode cancellation: Turn off power and execute the same button operations as when performing setup.) Panel lock mode DSP SIMULATION ZONE2 Operations using main unit panel buttons or master volume are rejected. Panel lock mode (Remove Master volume) DIRECT/ STEREO ZONE2Ope

49、rations using main unit panel buttons are rejected. Cancellation of panel lock mode PURE DIRECT ZONE2 Panel lock mode is cancelled. Installer Setup mode*1MENU CURSOR LEFT Access Remote Maintenance mode via the internet.Installer Setup is displayed on GUI/Option Menu. Refer to AVR4310_RemoteMaintenance_.pdf of SDI. ON/OFF RETURN ZONE2 DSP SIMULATION STANDARDSTATUSENTER PURE DIRECT DIRECT/ STEREO MENU CURSOR 16 AVR-4310CI/AVR-4310/AVC-4310 1. Version display (com/DSP Error Display) 1.1. Operation Spec com v