Toa Ic-100 Operating Instruction Manual 电路图.pdf

《Toa Ic-100 Operating Instruction Manual 电路图.pdf》由会员分享，可在线阅读，更多相关《Toa Ic-100 Operating Instruction Manual 电路图.pdf（72页珍藏版）》请在收音机爱好者资料库上搜索。

1、INSTITUTIONAL COMMUNICATION SYSTEM FUNCTIONS AND OPERATING INSTRUCTIONS Please follow the instructions in this manual to obtain the optimum results from this system. We also recommend that you keep this manual handy for future reference. TOA Corporation RadioFans.CN 收音机爱 好者资料库 MU-110 VERSION FCC REQ

2、UIREMENTS (1) (2) (3) (4) (5) (6) (7) (8) This equipment complies with Part 68 of the FCC rules. On the front panel of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested this information m

3、ust be provided to the telephone company. USOC JackRJ11C or RJ11W Service Order Code9.0F Facility Interface Code02LS2 The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in respo

4、nse to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs contact the telephone company to determine the maximum REN for the calling area. If the ter

5、minal equipment IC-100 causes harm to the telephone network, the telephone company will notify you in advance. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you b

6、elieve it is necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to

7、 maintain uninterrupted service. If trouble is experienced with this equipment IC-100, please contact Toa Electronics Inc., 601 Gateway Boulevard South Sanfrancisco, CA 9408023 No.415- 588-2538 for repair and warranty information. If the trouble is causing harm to the telephone network, the telephon

8、e company may request you remove the equipment from the network until the problem is resolved. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. This equipment is hearing aid compatible. DOC NOTICE 1. “NOTICE: The

9、 Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications networks protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the users satisfaction.

10、Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the companys inside wiring associated with a single li

11、ne individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorize

12、d Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the e

13、lectrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. 2 RadioFans.CN 收音机爱 好者资料库 Caution : Users should not attempt to make such connections themselv

14、es, but should contact the appropriate electric inspection authority, or electrician, as appropriate.” DOC NOTICE 2. ”The Load Number (88) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone Ioop which is used by the device, to prevent overloading

15、. The terminnation on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100.” DOC AVIS 1. “AVIS : -Ltiquette du ministre des Communications du Canada identifie Ie matiel homologu Cette tiquette certi

16、fie que Ie matriel est conforme certaines normes de protection, dexploitation et de scurit des rseaux de tlcommunications. Le Ministre nassure toutefois pas que Ie matriel fonctionnera la satisfaction de Iutilisateur. Avant dinstaller ce matriel, Iutilisateur doit sassurer quil est permis de Ie racc

17、order aux installations de Ientreprise locale de tlcommunication. Le matriel doit galement tre install en suivant une mthode accepte de raccordement. Dans certains cas, Ies fils intrieurs de Ientreprise utiliss pour un service individual Iigne unique peuvent tre prolongs au moyen dun dispositif homo

18、logu de raccordement (cordon prolongateur tlphonique interne). Labonn ne doit pas oublier quil est possible que la conformit aux conditions nonces ci-dessus nempechent pas la degradation du service dans certaines situations. Actuellement, Ies entreprises de tlcommunication ne permettent pas que Ion

19、raccorde Ieur matriel des jacks dabonn, sauf dans Ies cas prcis prvus par Ies tarifs particuliers de ces entreprises. Les rparations de matriel homologu doivent tre effectues par un centre dentretien canadien autoris dsign par Ie fournisseur. La compagnie de tlcommunications peut demander Iutilisate

20、ur de dbrancher un appareil la suite de reparations ou de modifications effectues par Iutilisateur ou cause de mauvais fonctionnement. Pour sa propre protection, Iutilisateur doit sassurer que tous Ies fils de mise la terre de la source dnergie lectrique, des Iignes tlphoniques et des canalisations

21、deau mtalliques, sil y en a, sent raccords ensemble. Cette prcaution est particulirement importance clans Ies rgions rurales. Avertissement. -Lutilisateur ne doit pas tenter de faire ces raccordements lui-mme; il doit avoir recours un service dnspection des installations lectriques, ou lectricien, s

22、elon Ie cas.” DOC AVIS 2. “Lindice de charge (88) assign chaque dispositif terminal indique, pour viter toute surcharge, Ie pourcentage de la charge totale qui peut tre raccorde un circuit tlphonique boucl utilis par ce dispositif. La terminaison du circuit boucl peut tre constitue de nimporte quell

23、e combinaison de dispositifs, pourvu que la somme des indices de charge de Iensemble des dispositifs ne dpasse pas 100.” 3 WARNING: (For U.S.A. only) This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may c

24、ause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subject J of Part 15 of FCC Rules, which are designed to provide reasonable protection such interference when operated in a commercial environment. Operation o

25、f this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference. CONTENTS Introduction7 Section 1. Sub-Station Operation 1.1 Nomenclature (1) RS-110 Sub-Station Han

26、dset (2) RS-100 Switch Panel (3) RS-120 Sub-Station (4) RS-130 Sub-Station 1.2 Sub-Station Speaker Communication (1) Calling (2) Being Called (3) Privacy Switch Use (4) Emergency Calls 1.3 Sub-station Handset Use (1) Calling (2) Being Called (3) Privacy Mode Conversation (4) Emergency Calls Section

27、2. Basic Control Station Operation 2.1 Nomenclature and Functions (1) AS-1OOA Control Station (2) AS-110 Control Station 2.2 Internal Line Call Operation (1) Calling (1.1) Control Station to Control Station (1.2) Control Station to Sub-Station (2) Being Called (3) (4) (5) (6) (2.1 ) Control Station

28、to Control Station (2.2) Sub-Station to Control Station Privacy Function Summary of Conversation Method Sub-Station Mode Displays Sub-Station Display Priorities (7)Emergency Functions (7.1)Emergency Call (7.2) Duress Alarm (7.3) Summary of Emergency Functions 2.3 0utside Call Operation (1) Calling (

29、2) Being Called 2.4 Paging (1) All-Call Paging (2) Zone Paging (3) Combination Zone Paging (4) Sub-Station Paging (5) Emergency All-Call Paging (6) PA paging (7) External Microphone All-Call Paging (8) Number of Zones (9) Temporary Station Output Disable (10) Summary of Paging Operation (11) Transmi

30、ssion Priority List (12) Dial Operation While Being Paged Section 3. Convenient Control Station Functions 3.1 Applicable to Both Internal and Outside Calls (1) Redialing (2) Speed Dialing (3) Call Transfer (4) Call Forwarding (5) Auto-Call C/O Transfer 3.2 Internal Line Calls (1) Selective Response

31、(2) Conference (3) Control Station Group Call 3.3 Scan Monitor (1) Automatic Scanning (1.1) Scan Monitor (1.2) Monitor Interval Registration (1.3) Scan Monitor Cancellation (2) Manual Scanning (2.1) Automatic Scanning Stop Permits manual operation of time signals. REDIAL key : Automatically redials

32、last dialed number. PROGRAM key: Programs zone distribution of program source. PRIORITY key :Establishes sub-station priority. ALL key : Broadcasts paging, time signal, and program source over entire area. ZONE key : Broadcasts paging, time signal, and program source to selected zones. PUSH TO TALK

33、key: Used in PTT operation ; Permits contact with stations in privacy mode ; Selects and dials displayed station. Hook switch Station number card EXTERNAL MIC/HEADSET REGISTER ON/OFF LINE SPEAKER VOLUME Top view Side view 15 (2) AS-110 Control Station (Console-/Wall-Mount Type) Front viewFront view

34、without a speaker cover Handset Display panel :Shows connection status and registered data. Internal speaker :Sounds call tones and permits “handsfree” conversation. C/# key : Terminates calls and accesses special C/O line functions as well as other special programing functions. Internal microphone

35、: Used in “handsfree” operation. EXTERNAL MIC/HEADSET jack : External microphone or headset jack. * key : Used for privacy mode selection and other special programing functions. 0-9 keypad: Used for dialing. In-use lamp REGISTER ON/OFF switch : Enables or disables system programing functions. Normal

36、ly set to OFF. SP : Adjusts internal speaker volume. MIC : Adjusts “handsfree” operation microphone sensitivity. DISPLAY CALLS key : Displays waiting station numbers, as well as registered data. TELEPHONE key : Accesses outside telephone lines. CONFERENCE key : Used to enable conference function. PA

37、GE key: Used for paging. TlME FUNCTION key: Selects pre-programed time schedules; Permits manual operation of time signals. REDIAL key : Automatically redials last dialed number. PROGRAM key: Programs zone distribution of program source. PRIORITYl key :Establishes sub-station priority. ALL key: Broa

38、dcasts paging, time signal, and program source over entire area. ZONE key : Broadcasts paging, time signal, and program source to selected zones. Permits contact with stations in privacy mode ; Selects and dials displayed station. Station number card Hook switch 16 Note: (1) (2) (3) (3.1) (3.2) (3.3

39、) (3.4) Dialing can be performed with either the handset Iifted or in place (handsfree operation). Likewise calls can be answered in either condition if the calls are from internal stations. System programing procedures are not provided in this manual. Refer to the accompanying Installation Manual f

40、or this information. Using an external headset or microphone Although use of the above-mentioned external headset and microphone are not explained in this manual, if a headset is connected, its operation is essentially the same as that of the handset. Likewise, if an external microphone is connected

41、, its operation is essentially the same as that of the internal microphone. When an external headset or microphone is connected to the MIC/HEADSET jack, a single tone is heard. Press theC/# key upon hearing the tone. (If the C/# key is not pressed, the “duress alarm” function is operated. In such ca

42、ses, press the C/# key, then remove the headset (microphone) from the jack.) To disable an internal speaker when using the headset, the control station has to be modified. (Refer to the IC-100 installation handbook.) Be sure to connect the headset (microphone) only when the exchange power is ON (i.e

43、. when characters are indicated on the display panel). Note that if the exchange power switch is set to ON with the headset (microphone) connected, a one-way conversation by PUSH TO TALK key will result instead of a simultaneous (duplex) conversation. 2.2Internal Line Call Operation (1) Calling (1.1

44、) Control station to control station Dial the desired station number. (Dialing can be performed with the handset lifted or replaced.) A brief call tone is heard at the calling station. Conversation can proceed when the called party answers. To terminate the conversation, replace the handset or press

45、 the C/# key. Note : Dialing can be performed with the handset either lifted or in place (handsfree dialing). Simultaneous full-duplex conversation is possible with the handset lifted once the called party answers. Full-duplex conversation is also possible when the calling station is in handsfree mo

46、de and the called party uses its handset. When both stations are in handsfree mode, only one-way PTT (Push to talk) conversation is possible, and the PUSH TO TALK key has to be pressed to talk and released to listen. However, should either party lift its handset during PTT operation, the conversatio

47、n will automatically be switched to full-duplex operation. (1.2) Control station to sub-station Dial the desired room station number. A brief call tone is heard. Lift up the handset or press PUSH TO TALK key. Conversation can proceed. To terminate the conversation, replace the handset or press the C

48、/# key. Note: Full-duplex conversation is possible when both the control station handset and sub-station handset are lifted. When the control station handset is lifted and sub-station communication is via the sub-station speaker, only half-duplex voice-actuated conversation is possible. When the con

49、trol station is in handsfree mode, only half-duplex PTT conversation is possible, regardless of the sub-station mode. Once the PUSH TO TALK key is pressed, full-duplex conversation becomes no longer possible. 18 (2) Being Called (2.1) (2.2) Control station to control station A brief call tone is heard. Conversation possible upon answering. Conversation ends. If the conversation has been terminated by the calling party, the called party need not operate any key for termination. The called party can terminate the conve