Marantz-SA8004v2-sacd-sm 电路图 维修手册.pdf

《Marantz-SA8004v2-sacd-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Marantz-SA8004v2-sacd-sm 电路图 维修手册.pdf（4页珍藏版）》请在收音机爱好者资料库上搜索。

1、Service Manual Some illustrations using in this service manual are slightly different from the actual set. Please use this service manual with referring to the operating instructions without fail. For purposes of improvement, specifi cations and design are subject to change without notice. Super Aud

2、io CD player SA8004 /K1SG/U1B SA-KI-PEARL-LITE /N1SG/N1B SA8004 SA-KI-PEARL-LITE SA8004 SA-KI-PEARL-LITE S0138-1V02DM/DG1009Copyright 2010 D press the 3 button, and the number goes down at 1% step. Press the 2 button at any value, and the setting for Open1 will be determined (between 0 and 500ms). O

3、nce the setting is determined, it will automatically determine the setting for Open2. Likewise, determine the setting for each of Open2 to Open5 and then for each of Close1 to Close5. When the Close5 setting is completed, the display will show the following message: Then, press the 2 button, and the

4、 OPEN/CLOSE operation will be repeated three times at the set speed. Meanwhile, press the 1 button while this message is on the display, and the OPEN/CLOSE test will be cancelled and the model indication will return to the display. However, the setting has been memorized so that the speed will remai

5、n unchanged. Also, press the 3 button while this message is on the display, and the OPEN/CLOSE test will be cancelled, the model indication will return and the setting will be cancelled. When the OPEN/CLOSE test is performed with the operation repeated three times, the display will show the followin

6、g message: Press the 2 button then, and the model identifi cation will return, and the OPEN/CLOSE will be performed at the set speed. If another button is pressed, the setting will be cancelled and the model identifi cation will return. Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA-

7、 B 1 S_T R A YP E E D = Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 _1O p e n_ X X X % _ Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 PST R Y _ T e s t ? Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 CPT R Y Sh a n g e ? 23 B The m

8、ode to check the last error message etc. This test mode is common to all models. 1. The error message displayed as the Last Error Message (1) Communication error between SA-CD Module and Microprocessor When having had the communication error with the SA-CD Module more than a regulated number of time

9、s, the unit will reset the SA-CD Module after displaying the following message. This will continue to be displayed until the unit has recovered from the communication error. When the unit is ready to play back CDs and SA-CDs, the SA-CD Module and the Microprocessor communicate regularly. Check the s

10、ignal in reference to the communication between the SA-CD Module and the Microprocessor on Communication Waveforms page. The MOD_SCL is the clock that is transmitted from the SA-CD regularly. If this signal cannot be detected, the SA-CD Module may be broken. If so, replace the SA-CD Module. When the

11、 SA-CD Module has been replaced, ensure that the Playtime will be cleared. (2) Communication Error between D/A Converter and Front Microprocessor If no response is detected in the communication between the D/A Converter and the Microprocessor, the display will show the following message. Make the CD

12、/SA-CD or the USB replayable. Ensure that IIC communications have been established between R217 and R218 when the unit is switched from STOP to PLAY. If the error cannot be corrected through normal operations, U204 may be broken. If such is the case, replace U204. 2. Error messages that are not disp

13、layed in the Last Error Message (1) Error messages that can be displayed on the FL (Communication Error between the Front Microprocessor and EEPROM) If no response is detected between the Front Microprocessor and EEPROM within a regulated timeframe, the display will show the following message. Ensur

14、e that IIC communications have been established between R123 and R125 when the unit is powered on or put into STANDBY. IF the error cannot be corrected through normal operations, U101 may be broke. If such is the case, replace U101. When no disc information is displayed 120 seconds after the disc is

15、 loaded, the display will show the following message. Reset the SA-CD Module. If no information can be obtained after this operation has been repeated three times, the unit will open the tray by itself. The unit cannot play back the disc if this message appears. Display Off RPTRNDMPROGTRKSA-CDCDM FI

16、LEUSBSTRGD OFF REMAINTTLA- B 1 C_S A C Do m _ E r r Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 rrD A C Eo r I I C _ Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 rEE R O Mr o r I I C Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 t_

17、 C a n_ P l a y _ 24 C Error Messages special to USB 1. Error Message displayed as the Last Error Message If no response is made in the communication between the USB Module U501 and the microprocessor within a designated timeframe, the display will show the following message. Refer to the Communicat

18、ion between USB Module and the microprocessor on the Communication Waveform page and check the signal. If the error message bellow cannot be cleared despite the unit performing normal operations properly, U501 may be broken. If such is the case, replace U501. If no response is made in the communicat

19、ion with an iPod-authenticated IC within a regulated timeframe, the display will show the following message. As the communication with the authenticated IC has not been established normally, ensure that the IIC signal is communicating at a normal level when the unit is connected with an iPod. The fr

20、equency of the IIC clock (IIC_SCL) is approximately 40 kHz only when the unit communicates with an iPod- authenticated IC. If no communication can be detected, check the soldering points of the microprocessor (U102), resistors (R155, R157) and the authenticated IC (U151). If the problem specifi c to

21、 the iPod cannot be rectifi ed, the authenticated IC (U151) may be broken. If that is the case, replace U151. When the iPod-authenticated IC has received error information, the display will show the following message. This message means that the authenticated IC is communicating properly. Try connec

22、ting another iPod. If no problem arises with another iPod, advise the user to repair the iPod. If the same problem arises with another iPod, the authenticated IC (U151) may be broken. If that is the case, replace U151. When a problem arises with the processing of the iPod authentication and signatur

23、e, the display will show the following message. If the following message appears instead of the above messages - iPodErrorIC”, iPodICErrorx and USB_Com_ Error_, try connecting another iPod. If no problem arises, advise the user to repair the iPod. If the error message persists, the authenticated IC

24、(U151) may be broken. If that is the case, replace U151. Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 oCU S B _m _ E r r _ Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 rEi P o dr o r I I C Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B

25、 1 CIi P o dE r r o r x Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 tuE r r Ah e n t i C 25 2. Error Message not displayed as the Last Error Message (1) Error Message that is displayed when UBS memories and USB HDD are used If no response is made while the unit is communicati

26、ng with the USB Module, the display will show the following message. If the indication will not be changed to USB_Com_Err, the communication may be unstable. Refer to the communication between the USB module and the microprocessor on the communication waveform page and check the signal. If the messa

27、ge below cannot be cleared while the unit is functioning normally, U501 may be broken. If that is the case, replace U501. When the unit is connected with an incompatible UBS device or a device confi gured with an incompatible communication protocol or command, the display will show the following mes

28、sage. If this message is displayed, the device is incompatible and cannot be connected to the unit. If the information obtained from the USB has a fl aw or improper data, which are detected by the USB host controller in the unit, the display will show the following message. When the message appears,

29、 the device may be connected and used, but success is not guaranteed. If the signal comes in an incompatible format, the display will show the following message. The compatible formats are FAT16 and FAT32. In FAT32 the USB memory must be 128MB or bigger in size. This message means that the device is

30、 formatted in an incompatible cluster size. Normally, when USB memories are formatted on Microsoft Windows, FAT32 is the default, and if the memory size is up to 128MB, it will be formatted in a cluster size of 2KB, which is incompatible with the unit. Therefore, the memory size is recommended to be

31、 256MB or bigger. If the memory size is 128MB, format it with FAT16 (indicated as FAT on Microsoft Windows) instead of FAT32, and it will be compatible with the unit. Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 RRU S B E: E F : x x Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBST

32、RGD OFF REMAINTTLA- B 1 CtC a n o n n e c t Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 ceC o n nt E r r o r Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 E_ F A Tr r o r _ _ Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 etC I u sr

33、_ E r r _ 26 If no playable fi le exists in the USB device connected to the unit, the display will show the following message: If the unit receives a power supply exceeding the maximum level (1 A) via USB, the display will show the following message and the power supply will be cut off. If the messa

34、ge below appears, the USB device cannot be operated through the units USB Bus power alone. An auxiliary power unit might enable the device to be used, but damage resulting from this would not be covered by the warranty. If the command will not be set within a set timeframe after PLAY, PAUSE, STOP, F

35、F, FR and such operations are carried out, the display will show the following message. This message will be displayed for 3 seconds and then the USB module will be reset. If the error indication persists after these operations, U501 may be broken as the unit will not accept a specifi c command alon

36、e. If no other error message will appear, replace U501. If the fi le has an incompatible extension or is 24KB or smaller in size, the display will show the following message. Extensions other than those mentioned in the instructions manual will be excluded from the warranty. Refer to the instruction

37、s manual and ensure that the extension and format is compatible with the unit. If the unit detects an incompatible sampling frequency or number of channels or an incompatible format fi le, the display will show the following message. Sampling frequencies, numbers of channels and formats other than t

38、hose mentioned in the instructions manual will be excluded from the warranty. Refer to the instructions manual and ensure that the format is incompatible. If the unit detects a DRM protected fi le, the display will show the following message. The unit is not made to and hence cannot play back DRM pr

39、otected fi les. Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 FtC I N oi l e r r _ Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 uCO v e rr r e n t _ Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 iTU S B rm e e O u t Display Off RPTRN

40、DMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 ieU F i lE r r o r t Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 reH e a dE E r r o r Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 SeH D R Mt r e a m r 27 If the unit detects a fi le with corrupted fi l

41、e data or other unacceptable fi les, the display will show the following message. If the fi le includes big sized image data or information, the analysis may take time. If the analysis takes more than 15 seconds, the display will show the following message. If this message appears, the operation of

42、the fi le will not be covered by the warranty. If the USB module turns off the command for the settings of AMS, Repeat or Random, the display will show the following message. If the error persists after the mode is switched to Disc from USB and then reswitched to USB and the designated remote contro

43、l code is sent, U501 may be broken as it will not accept a specifi c command alone. If no other error message appears, replace U501. If the USB module turns off the command for setting AMS, Repeat or Random and specifying the range, the display will show the following message. If the error persists

44、after the mode is switched to Disc from USB and then reswitched to USB and the designated remote control code is sent, U501 may be broken as it will not accept a specifi c command alone. If no other error message appears, replace U501. When the unit has failed to search for a folder or a fi le, obta

45、in folder information or set the default, the display will show the following message. If this error repeats, U501 may be broken. If that is the case, replace U501. Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 aeH S t rm r E r r r Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRG

46、D OFF REMAINTTLA- B 1 emH S T im O u t r r Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 dox h T Me O E r r r Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 deR a n gE r r o r r Display Off RPTRNDMPROGTRKSA-CDCDM FILEUSBSTRGD OFF REMAINTTLA- B 1 dpS e t uE

47、r r o r r 28 If the unit has failed to obtain information of the fi le to be played back, the display will show the following message. If this error occurs to a specifi c fi le, the fi le information may be corrupted. Check the fi le header and other information. If the error occurs to all fi les, U

48、501 may be broken. If no other error message appears, replace U501. If the unit has failed to obtain information of the SB manufacturer, the product and the serial number, the display will show the following message. On the display, the x will be replaced by the number 1, 2 or Failed to obtain manuf

49、acturer information; 2. Failed to obtain product information; 3. Failed to obtain serial number If this message appears, use of the device will not be covered by the warranty. If the unit has failed to set a decodable fi le, the display will show the following message. If the error persists after the mode is switched to Disc from USB and then reswitched to USB and the designated remote control code is sent, U501 may be broken as it will not accept a specifi c command alone. If no other error message appears, replace U501. - Display Off RPTRNDMPROGTR