Sony-BDPS560-bdp-sm 电路图 维修手册.pdf

《Sony-BDPS560-bdp-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-BDPS560-bdp-sm 电路图 维修手册.pdf（132页珍藏版）》请在收音机爱好者资料库上搜索。

1、Sony Corporation Video Business Group SERVICE MANUAL 9-890-712-11 2009F0500-1 2009.6 Published by Quality Assurance Dept. BLU-RAY DISC/DVD PLAYER Ver. 1.0 2009.06 BDP-S560 RMT-B104A SPECIFICATIONS US Model Canadian Model System Laser: Semiconductor laser Inputs and outputs (Jack name: Jack type/Outp

2、ut level/Load impedance) LINE OUT R-AUDIO-L: Phono jack/2 Vrms/10 kilohms DIGITAL OUT (OPTICAL): Optical output jack/18 dBm (wave length 660 nm) DIGITAL OUT (COAXIAL): Phono jack/0.5 Vp-p/75 ohms HDMI OUT: HDMI 19-pin standard connector COMPONENT VIDEO OUT (Y, PB, PR): Phono jack/Y: 1.0 Vp-p/ PB, PR

3、: 0.7 Vp-p/75 ohms LINE OUT VIDEO: Phono jack/1.0 Vp-p/75 ohms LINE OUT S VIDEO: 4-pin mini DIN/ Y: 1.0 Vp-p, C: 0.286 Vp-p/75 ohms LAN (100): 100BASE-TX Terminal EXT: External memory slot (For connecting the external memory) DC output: 5 V 500 mA Max USB: USB jack Type A (For connecting digital sti

4、ll camera and USB memory) Wireless Wireless LAN standard: IEEE802.11a/b/g IEEE802.11n draft 2.0 Frequency range: U.S. models: 2.4 GHz band: Channels 1-11 5 GHz band: Channels 36-64, 100-140, 149-165 Canada models: 2.4 GHz band: Channels 1-11 5 GHz band: Channels 36-64, 100-116, 132-140, 149-165 Modu

5、lation: DS-SS Modem and OFDM Modem General Power requirements: 120 V AC, 60 Hz Power consumption: 28 W Dimensions (approx.): 430 mm 216 mm 70 mm (17 in. 8 5/8 in. 2 13/16 in.) (width/depth/height) incl. projecting parts Mass (approx.): 2.4 kg (5 lb 4 5/8 oz) Operating temperature: 5 C to 35 C (41 F

6、to 95 F) Operating humidity: 25 % to 80 % Supplied accessories Specifications and design are subject to change without notice. ? Audio/video cable (phono plug 3) (1) ? AC power cord (1) ? Remote commander (remote) (1) ? Size AA (R6) batteries (2) RadioFans.CN 收音机爱 好者资料库 2 BDP-S560 SAFETY CHECK-OUT L

7、EAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such a

8、s the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltme

9、ter. The “limit” indication is 0.75V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) 1. Check the area of y

10、our repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that

11、 were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the line cord for cracks and abrasion.

12、Recommend the replacement of any such line cord to the customer. 6. Check the B+ voltage to see it is at the values specified. 7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. After correcting

13、the original service problem, perform the following safety checks before releasing the set to the customer: 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. Unleaded solder Boards requiring use of unleaded solder are prin

14、ted with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about

15、 40C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350C. Caution: The printed pattern (copper foil) may peel away if the heated

16、tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solde

17、r may also be added to ordinary solder. CAUTION: The use of optical instrument with this product will increase eye hazard. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radia- tion exposure. This label is located on the

18、laser protective housing inside the enclosure. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 25 cm FROM THE SURFACE OF THE OBJEC- TIVE LENS ON THE OPTICAL PICK-

19、UP BLOCK. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK ? OR DOTTED LINE WITH MARK ? ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. RE- PLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLIS

20、HED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE ? SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU

21、 DANS LES SUPPL- MENTS PUBLIS PAR SONY. RadioFans.CN 收音机爱 好者资料库 3 BDP-S560 TABLE OF CONTENTS Section Title PageSection Title Page 1. SERVICE NOTE 1-1. Disc Removal Procedure If The Tray Cannot Be Ejected (Forced Ejection) . 1-1 1-2. Work when optical device are replaced . 1-1 1-3. Test Disc . 1-2 1-

22、3-1. Operation and Display . 1-2 2. DISASSEMBLY 2-1. Disassembly Flow . 2-1 2-2. Upper Case . 2-1 2-3. Front Panel Block . 2-2 2-4. BD Drive . 2-3 2-5. Wireless Lan Card Block . 2-3 2-6. Rear Panel Block. 2-4 2-7. MB-127 Board . 2-4 2-8. Switching Regulator . 2-5 2-9. Circuit Boards Location . 2-5 3

23、. BLOCK DIAGRAMS 3-1. Overall Block Diagram. 3-1 3-2. DSP Block Diagram . 3-2 3-3. AV OUT Block Diagram . 3-3 3-4. USB/ETHER, FL Block Diagram . 3-4 3-5. Power Block Diagram (1/3) . 3-5 3-6. Power Block Diagram (2/3) . 3-6 3-7. Power Block Diagram (2/3) . 3-7 4. SCHEMATIC DIAGRAMS 4-1. This Note Is

24、Common For Schematic Diagrams . 4-1 4-2. Frame Schematic Diagram. 4-2 4-3. ANT-001 Board (ANTENNA) Schematic Diagram. 4-3 4-4. ANT-002 Board (ANTENNA) Schematic Diagram. 4-4 4-5. FL-194 Board (SWITCH) Schematic Diagram . 4-5 4-6. FR-302 Board (FL DRIVER) Schematic Diagram . 4-6 4-7. HU-012 Board (US

25、B HUB) Schematic Diagram. 4-7 4-8. MB-127 Board (EMMA3P DDR2-A) Schematic Diagram (1/14). 4-8 4-9. MB-127 Board (EMMA3P DDR2-B) Schematic Diagram (2/14). 4-9 4-10. MB-127 Board (POWER1) Schematic Diagram (3/14). 4-10 4-11. MB-127 Board (CLK/POWER2) Schematic Diagram (4/14). 4-11 4-12. MB-127 Board (

26、FLASH/HOST) Schematic Diagram (5/14). 4-12 4-13. MB-127 Board (USB) Schematic Diagram (6/14). 4-13 4-14. MB-127 Board (HDMI/SATA) Schematic Diagram (7/14). 4-14 4-15. MB-127 Board (AUDIO/VIDEO) Schematic Diagram (8/14). 4-15 4-16. MB-127 Board (GPIO/JTAG) Schematic Diagram (9/14). 4-16 4-17. MB-127

27、Board (IPIO) Schematic Diagram (10/14). 4-17 4-18. MB-127 Board (ETHERNET) Schematic Diagram (11/14) . 4-18 4-19. MB-127 Board (RF SDRAM) Schematic Diagram (12/14). 4-19 4-20. MB-127 Board (DRIVE/RF) Schematic Diagram (13/14). 4-20 4-21. MB-127 Board (IFD) Schematic Diagram (14/14) . 4-21 4-22. USB-

28、016 Board (USB REAR CONNECTOR) Schematic Diagram . 4-22 4-23. USB-017 Board (USB FRONT CONNECTOR) Schematic Diagram . 4-23 4-24. Waveforms . 4-24 5. PRINTED WIRING BOARDS 5-1. This Note Is Common For Printed Wiring Boards . 5-1 5-2. ANT-001 Board (ANTENNA) Printed Wiring Board . 5-2 5-3. ANT-002 Boa

29、rd (ANTENNA) Printed Wiring Board . 5-3 5-4. FL-194 Board (SWITCH) Printed Wiring Board. 5-4 5-5. FR-302 Board (FL DRIVER) Printed Wiring Board . 5-5 5-6. HU-012 Board (USB HUB) Printed Wiring Board . 5-6 5-7. MB-127 Board (MAIN) Printed Wiring Board (Side A) . 5-7 5-8. MB-127 Board (MAIN) Printed W

30、iring Board (Side B) . 5-8 5-9. USB-016 Board (USB REAR CONNECTOR) Printed Wiring Board . 5-9 5-10. USB-017 Board (USB FRONT CONNECTOR) Printed Wiring Board . 5-10 6. IC PIN FUNCTION DESCRIPTION . 6-1 7. SERVICE MODE . 7-1 8. ERROR LOG LIST . 8-1 9. TROUBLESHOOTING . 9-1 10. REPAIR PARTS LIST 10-1.

31、Exploded Views . 10-1 10-1-1. Case Section . 10-1 10-1-2. Front/Rear Chassis Section . 10-2 10-1-3. Main Chassis Section . 10-3 10-1-4. BD Section . 10-4 10-1-5. Accessories . 10-5 10-2. Electrical Parts List . 10-6 RadioFans.CN 收音机爱 好者资料库 1-1 BDP-S560 SECTION 1 SERVICE NOTE 1-1. DISC REMOVAL PROCED

32、URE IF THE TRAY CANNOT BE EJECTED (FORCED EJECTION) 1. Remove the upper case. (Refer to page 2-1) 2. Insert a clip in the hole of a drive and open a tray. Note: Use a clip of about 1.2 mm in the diameter 1-2. Work when optical device are replaced Note: Please do the following work when you replace t

33、he optical device. 1. Install it in PC after downloading two set of software from following URL. (About the procedure, refer to the attached Readme.txt file) STEP 1 Microsoft .NET Framework Version 2.0 Redistributable Package (x86) 20,000 series - 4-4 BDP-S560 3P CN301 PAT301 WIRELESS A ANT-002 BOAR

34、D BLK 12 05 ANTENNA LAN CARD 3 B 4-4. ANT-002 BOARD (ANTENNA) SCHEMATIC DIAGRAM See page 5-3 for printed wiring board. - Ref. No.: ANT-002 board; 20,000 series - 4-5 BDP-S560 4-5. FL-194 BOARD (SWITCH) SCHEMATIC DIAGRAM See page 5-4 for printed wiring board. - Ref. No.: FL-194 board; 20,000 series -

35、 S331 1 2 2P CN331 A FL-194 BOARD 12 05 SWITCH 3 B REGULATOR SWITCHING / GND P ON 4-6 BDP-S560 4-6. FR-302 BOARD (FL DRIVER) SCHEMATIC DIAGRAM See page 5-5 for printed wiring board. - Ref. No.: FR-302 board; 20,000 series - 3.3 -18.7 -18.7 -18.8 -18.7 -18.7 -18.7 -18.7 -18.8 -21.2 -16.2 -21.4 -21 -2

36、1 -21 -13.7 -9 -18.5 -13.7 3.3 -18.5 -11.1 -21 -20.9 -21 -11.2 -11.5 -13.8 -13.6 0 0 0 1.9 0.1 3 2.6 3.3 3.3 5.75.6 4.9 0.1 3.3 5.4 0 5.4 0 5.4 0 5.6 0 0 5.6 5.75.6 4.9 0.1 3.3 NO MARK:PB MODE JL711 JL726 JL707 JL724 0.1 C711 0.1 C713 JL715 2 3 5 6 8 7 1 10 4 9 T701 JL723 JL725 D703 1SS355TE-17 JL70

37、6 D706 1SS355TE-17 100k R715 JL722 XX C718 JL710 JL714 JL730 JL713 JL701 JL705 16V 100 C703 0.01 C714 JL721 JL732 R716 XX D704 1SS355TE-17 C716 0.1 1 2 3 4 5 6 7 8 9 10 11 1213141516171819202122 23 24 25 26 27 28 29 30 31 32 33 3435363738394041424344 IC702 PT6315 LED1 LED2 LED3 LED4 OSC DOUT DIN CLK

38、 STB K1 K2 VSS VDD SG1 SG2 SG3 SG4 SG5 SG6 SG7 SG8 SG9 SG10 SG11 SG12 SG13 SG14 SG15 SG16 VEE GR12 GR11 GR10 GR9 GR8 GR7 GR6 GR5 GR4 GR3 GR2 GR1 VDD VSS JL709 JL729 JL720 JL704 4.7k R714 JL716 JL708 3.9k R707 C715 0.01 C705 250V 6800p XX C710 JL719 JL728 Q707 2SC2411K-T-146-CR 50V 22 C712 XX R706 JL

39、702 JL703 XX C709 D705 1SS355TE-17 JL712 D707 MAZ8047GMLS0 JL727 Q706 2SC2411K-T-146-CR JL731 XX C708 VCC OUT GND IC701 GP1UE27XK0VF 123 0.01 C707 S702S701 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 17P CN701 2SB1197K-T-146-R Q704 MUN2213T1 Q703 10k R701 R704 XX C701 0.1 1k R705 C702 XX L701 100uH ND

40、701 1567891011121314151617181920212223242526272829313224 16V C704 47 2.2k R712 2SB1197K-T-146-R Q705 MUN2213T1 Q708 270 R717 220 R723 4.7k R718 2.2k R719 D709 CL-270S-WS-SD-TS D708 CL-482S-HB8-SD-TS 180 R720 CL-197HG5-CD-T D710 MUN2213T1 Q709 MUN2213T1 Q710 MUN2213T1 Q711 S704 2.2k R721 0.4A PS701 R

41、724 10k 47 R725 10 C719 150p C717 SEG11 SEG4 SEG10 SEG3 SEG2 SEG1 GRD8 GRD7 GRD6 GRD5 GRD4 GRD3 GRD2 GRD1 GRD12 GRD11 SEG16 SEG9 SEG15 SEG8 SEG14 SEG7 SEG13 SEG6 SEG12 SEG5 LED_DT LED_CK FLD_STB LED_CK FLD_STB GRD1 GRD2 GRD3 GRD4 GRD5 GRD6 GRD7 GRD8 GRD11 GRD12 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 LED_DT P13 2G P7 3G P12 P4 4G 11G P11 P5 5G P10