Zenith-DVB611-dvd-sm电路图 维修手册.pdf

《Zenith-DVB611-dvd-sm电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Zenith-DVB611-dvd-sm电路图 维修手册.pdf（63页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL Product Type: DVD VIDEO PLAYER Chassis: DP-10 (MD) Manual Series: DVB611 Manual Part #: 3829RHP051M Model Line: D Product Year: 2006 Summary 1 Cabinet CONNECT A 1500 OHM 10 WATT RESIS- TOR, PARALLELED BY A .15 MFD. 150.V A.C TYPE CAPACITOR BETWEEN A KNOWN GOOD EARTH GROUND (WATER PIPE

2、, CON- DUIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME. MEASURE THE A.C. VOLTAGE ACROSS THE COMBINATION OF 1500 OHM RESISTOR AND .15 MFD CAPACITOR. REVERSE THE A.C. PLUG AND REPEAT A.C. VOLTAGE MEASUREMENTS FOR EACH EXPOSED METALLIC PART. VOLTAGE MEASURED MUST NOT EXCEED 75 VOLTS R.M.S. TH

3、IS CORRESPONDS TO 0.5 MILLIAMP A.C ANY VALUE EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED IMMEDIATELY. SUBJECT: GRAPHIC SYMBOLS THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF

4、UNINSULATED “DANGEROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAG- NITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK. THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIAN- GLE IS INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE LITERATURE. SUBJECT : X-RADIATION

5、 1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PER- SONNEL COVER THE SUBJECT OF X-RADIATION. THE ONLY POTEN- TIAL SOURCE OF X-RAYS IN CURRENT T.V. RECEIVERS IS THE PIC- TURE TUBE. HOWEVER, THIS TUBE DOES NOT EMIT X-RAYS WHEN THE HIGH VOLTAGE IS AT THE FACTORY SPECIFIED LEVEL. THE PROPER VALU

6、E IS GIVEN IN THE APPLICABLE SCHEMATIC. OPERA- TION AT HIGHER VOLTAGES MAY CAUSE A FAILURE OF THE PIC- TURE TUBE OR HIGH VOLTAGE SUPPLY AND, UNDER CERTAIN CIR- CUMSTANCES, MAY PRODUCE RADIATION IN EXCESS OF DESIR- ABLE LEVELS. 2. ONLY FACTORY SPECIFIED C.R.T. ANODE CONNECTORS MUST BE USED. DEGAUSSIN

7、G SHIELDS ALSO SERVE AS X-RAY SHIELD IN COLOR SETS, ALWAYS RE-INSTALL THEM. 3. IT IS ESSNTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE AN ACCURATE AND RELIABLE HIGH VOLTAGE METER. THE CALIBRA TION OF THE METER SHOULD BE CHECKED PERIODICALLY AGAINST A REFERENCE STANDARD, SUCH AS THE ONE AVAILABLE AT YOU

8、R DISTRIBUTOR. 4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLY THERE IS NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERY TIME A COLOR CHASSIS IS SERVICED. THE BRIGHTNESS SHOULD BE RUN UP AND DOWN WHILE MONITORING THE HIGH VOLTAGE WITH A METER TO BE CERTAIN THAT THE HIGH VOLTAGE DOES NOT EXCE

9、ED THE SPECIFIED VALUE AND THAT IT IS REGULATING CORRECTLY, WE SUGGEST THAT YOU AND YOUR SERVICE ORGA- NIZATION REVIEW TEST PROCEDURES SO THAT VOLTAGE REGU- LATION IS ALWAYS CHECKED AS A STANDARD SERVICING PROCE- DURE. AND THAT THE HIGH VOLTAGE READING BE RECORDER ON EACH CUSTOMERS INVOICE. 5. WHEN

10、TROUBLESHOOTING AND MAKING TEST MEASUREMENTS IN A PRODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE, AVOID BEING UNNECESSARILY CLOSE TO THE PICTURE TUBE AND THE HIGH VOLTAGE SUPPLY. DO NOT OPERATE THE PRODUCT LONGER THAN IS NECESSARY TO LOCATE THE CAUSE OF EXCES SIVE VOLTAGE. 6. REFER TO HV. B+ AND S

11、HUTDOWN ADJUSTMENT PROCEDURES DESCRIBED IN THE APPROPRIATE SCHEMATIC AND DIAGRAMS (WHERE USED). SUBJECT: IMPLOSION 1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTE GRAL IMPLOSION PROTECTION SYSTEM, BUT CARE SHOULD BE TAKEN TO AVOID DAMAGE DURING INSTALLATION, AVOID SCRATCHING THE TUBE. I

12、F SCRATCHED REPLACE IT. 2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES. SUBJECT : TIPS ON PROPER INSTALLATION 1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS, CUBBY- HOLE OR CLOSELY FITTING SHELF SPACE. OVER OR CLOSE TO HEAT DUCT, OR IN THE PATH OF HEATED AIR FLOW. 2. AVOID CONDITIONS OF HIGH

13、HUMIDITY SUCH AS: OUTDOOR PATIO INSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIA- TORS WHERE STEAM LEAKAGE IS A FACTOR, ETC. 3. AVOID PALCEMENT WHERE DRAPERIES MAY OBSTRUCT REAR VENTING. THE CUSTOMER SHOULD ALSO AVOID THE USE OF DEC- ORATIVE SCARVES OR OTHER COVERINGS WHICH MIGHT OBSTRUCT VENTI

14、LATION. 4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMER- CIAL MOUNTING KIT. MUST FOLLOW THE FACTORY APPROVED MOUNTING INSTRUCTIONS A PRODUCT MOUNTED TO A SHELF OR PLATFORM MUST RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENT THICKNESS IN SPACERS) TO PROVIDE ADEQUATE AIR FLOW ACROSS THE BOTTOM, BO

15、LTS OR SCREWS USED FOR FASTENERS MUST NOT TOUCH ANY PARTS OR WIRING. PERFORM LEAKAGE TEST ON CUSTOMIZED INSTALLATIONS. 5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ON SLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT IS PROPERLY SECURED. 6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STA

16、BLE ON ITS MOUNTING TO THE CART. CAUTION THE CUSTOMER ON THE HAZ- ARDS OF TRYING TO ROLL A CART WITH SMALL CASTERS ACROSS THRESHOLDS OR DEEP PILE CARPETS. 7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STAND WHICH HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES, INC. FOR USE WITH THEIR SPECIFIC

17、MODEL OF TELEVISION RECEIVER OR GENERICALLY APPROVED FOR USE WITH T.V.S OF THE SAME OR LARGER SCREEN SIZE. 8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS, EXPLAIN THAT A FOREST OF EXTENSIONS SPROUTING FROM A SIN- GLE OUTLET CAN LEAD TO DISASTROUS CONSEQUENCES TO HOME AND FAMILY. PRODUCT SAF

18、ETY SERVICING GUIDELINES FOR VIDEO PRODUCTS A.C. VOLTMETER GOOD EARTH GROUND SUCH AS THE WATER PIPE. CONDUIT. ETC PLACE THIS PROBE ON EACH EXPOSED METAL PART 1-4 SERVICING PRECAUTIONS CAUTION : Before servicing the DVD covered by this service data and its supplements and addends, read and follow the

19、 SAFETY PRECAUTIONS. NOTE : if unforeseen circum- stances create conflict between the following servicing pre- cautions and any of the safety precautions in this publica- tions, always follow the safety precautions. Remembers Safety First: General Servicing Precautions 1. Always unplug the DVD AC po

20、wer cord from the AC power source before: (1)Removing or reinstalling any component, circuit board, module, or any other assembly. (2)Disconnection or reconnecting any internal electrical plug or other electrical connection. (3)Connecting a test substitute in parallel with an elec- trolytic capacito

21、r. Caution : A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. 2. Do not spray chemicals on or near this DVD or any of its assemblies. 3. Unless specified otherwise in this service data, clean electrical contacts by applying an

22、 appropriate contact cleaning solution to the contacts with a pipe cleaner, cotton-tipped swab, or comparable soft applicator. Unless specified otherwise in this service data, lubrication of contacts is not required. 4. Do not defeat any plug/socket B+ voltage interlocks with whitch instruments cove

23、red by this service manual might be equipped. 5. Do not apply AC power to this DVD and/or any of its electrical assemblies unless all solid-state device heat sinks are cerrectly installed. 6. Always connect test instrument ground lead to the appropriate ground before connection the test instrument p

24、ositive lead. Always remove the test instrument ground lead last. Insulation Checking Procedure Disconnect the attachment plug from the AC outlet and turn the power on. Connect an insulation resistance meter(500V) to the blades of the attachment plug. The insulation resis- tance between each blade o

25、f the attachment plug and acces- sible conductive parts (Note 1) should be more than 1M- ohm. Note 1 : Accessible Conductive Parts including Metal pan- els, Input terminals, Earphone jacks, etc. Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily b

26、y static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of comp

27、onent damage caused by static electricity. 1. Immediately before handling any semiconductor compo- nent or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commer- cially available discharging wrist st

28、rap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of

29、the assembly. 3. Use only a grouned-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified a “anti-static” can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemica

30、ls. These can generate electrical charge sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protec tive package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam,

31、 aluminum foil, or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Caution : Be sure no power is applied to the

32、 chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Normally harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static elec- tricit

33、y sufficient to damage an ES device.) 1-5 SERVICE INFORMATION FOR EEPROM POWER ON DVD LOGO Status (NO Disk status) Remotecontrol Pause key-1-4-7-2 in order. Press number 09, Press charater AF (16 for a while) Use arrow key (F D G E) to move to approprite position and make changes Press pause key onc

34、e Change will be applied when power OFF-ON. MODELDVB611 NAMEHEX OPT 155(U) OPT 253(S) OPT 300(ENG) OPT 445 OPT 502 OPT 655 OPT 7E4 DETECT NEW EEPROM (OPTION EDIT SCREEN) 1-6 SPECIFICATIONS GENERAL Power requirements: AC 120V , 60Hz Power consumption: 8W Dimensions (Approx.): 430 x 35 x 242 mm (17 x

35、1.4 x 9.5 inches) (W x H x D) with- out foot Weight (Approx.): 1.7 kg (3.7 lbs) Operating temperature:5 C to 35 C (41 F to 95 F) Operating humidity: 5 % to 90 % OUTPUTS VIDEO OUT:1 V (p-p), 75 , sync negative, RCA jack x 1 S-VIDEO OUT:(Y) 1.0 V (p-p), 75 , negative sync, Mini DIN 4-pin x 1 (C) 0.3 V

36、 (p-p) 75 COMPONENT VIDEO OUT:(Y) 1.0 V (p-p), 75 ,negative sync, RCA jack x 1 (Pb)/(Pr) 0.7 V (p-p), 75 , RCA jack x 2 AUDIO OUT:2.0 Vrms (1 KHz, 0 dB), 600 , RCA jack (L, R) x 1 DIGITAL OUT (COAXIAL):0.5 V (p-p), 75 , RCA jack x 1 DIGITAL OUT (OPTICAL) (OPTIONAL): 3 V (p-p), 75 , Optical jack x 1

37、SYSTEM Laser:Semiconductor laser, wavelength 650 nm Signal system: PAL / NTSC Frequency response:DVD (PCM 96 kHz): 8 Hz to 44 kHz DVD (PCM 48 kHz): 8 Hz to 22 kHz CD: 8 Hz to 20 kHz Signal-to-noise ratio:More than 100 dB (ANALOG OUT connectors only) Harmonic distortion: Less than 0.008% Dynamic rang

38、e:More than 95 dB (DVD/CD) 72-1 SECTION 2 CABINET & MAIN CHASSIS CONTENTS EXPLODED VIEWS.2-2 1. Cabinet and Main Frame Section.2-2 2. Deck Mechanism Section(DP-10).2-3 3. Packing Accessory Section.2-4 82-2 EXPLODED VIEWS 1. Cabinet and Main Frame Section A42 A43 A49 A47 A00 A44 A46 283 280 452 452 C

39、N902 P101 CABLE90 463 465 465 463 463 250 463 463 467 260 261 261 300 320 463 NOTES)THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE LITERATURE. A 5 4 3 2 1 BCD 9 2. Deck Mechanism Section(DP-10

40、) 2-3 001 002 003 020 439 018 013 017 015B 015A 440 019 012 015 012 432 030 010 439 431 435 021 430 024 025 036 012A 012A 026 016 435 014 A01 A02 A03 A00 102-4 3. Packing Accessory Section BATTERY808 PACKING SHEET804 PACKING OPTIONAL PARTS 803 806 820 OWNERS MANUAL RF CABLE 810 CABLE SET ASSY 801 RE

41、MOCON900 BOX CARTON802 PACKING803 811 812 PLUG ASSY 1WAY(YELLOW) PLUG ASSY 1WAY(BLACK) PLUG ASSY 2WAY 3-1 SECTION 3 ELECTRICAL CONTENTS ELECTRICAL TROUBLESHOOTING GUIDE.3-2 1. Power check flow.3-2 2. System operation flow .3-3 3. Test & debug flow.3-4 DETAILS AND WAVEFORMS ON SYSTEM TEST AND DEBUGGI

42、NG.3-10 1. SYSTEM 27MHz CLOCK, RESET SIGNAL.3-10 2. SDRAM CLOCK.3-12 3. TRAY OPEN/CLOSE SIGNAL.3-12 4. SLED CONTROL RELATED SIGNAL(NO DISC CONDITION).3-13 5. LENS CONTROL RELATED SIGNAL(NO DISC CONDITION).3-13 6. LASER POWER CONTROL RELATED SIGNAL(NO DISC CONDITION).3-14 7. DISC TYPE JUDGEMENT WAVEF

43、ORM.3-14 8. FOCUS ON WAVEFORM.3-16 9. SPINDLE CONTROL WAVEFORM(NO DISC CONDITION.3-17 10. TRACKING CONTROL RELATED SIGNAL(System checking).3-18 11. RF WAVEFORM .3-19 12. ZR36882 AUDIO OPTICAL AND COAXIAL OUTPUT(SPDIF).3-19 13. ZR36882 VIDEO OUTPUT WAVEFORM.3-20 14. AUDIO OUTPUT FROM AUDIO DAC .3-21 BLOCK DIAGRAMS.3-23 1. Overall Block Diagram .3-23 2.