Rotel-RSX1065v02-ssr-sm 电路图 维修手册.pdf

《Rotel-RSX1065v02-ssr-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Rotel-RSX1065v02-ssr-sm 电路图 维修手册.pdf（41页珍藏版）》请在收音机爱好者资料库上搜索。

1、T echnical Manual SURROUND SOUND RECEIVER RSX-1065 Table of Contents Specification.1 Parts List.212 Adjustment.1314 Wiring.18 Disassembly Diagram and List.1617 PCB Assembly.1927 Schematic Diagram .2841 SHINSEN-BLD. 4F 10-10 SHINSEN-CHO, SHIBUYA-KU, TOKYO 150-0045, JAPAN Serial. NO. Beginning Quality

2、 Uncompromised Y-357B-0110/pdf THE ROTEL CO., LTD. Antenna Input 75 ohms unbalanced AM Tuner Sensitivity 500 uV/m Signal to Noise Ratio 40 dBf Output level 500 mV Antenna Input Loop Antenna General Power Consumption: 550 watts Power Requirements (AC) 115 volts, 60Hz (USA version) 230 volts, 50Hz (CE

3、 version) Weight 20.4 Kg/44.9 lb. Dimensions (W x H x D) 432 x 189 x 427 mm 17 x 71/2 x 167/8 Front Panel Height (feet removed/for rack mount) 176 mm / 7 Specifications Audio Continuous Amplifier Power (five channels driven) 100 watts/ch (20-20k Hz, 0.05% THD, 8 ohms) Continuous Amplifier Power (two

4、 channels driven) 120 watts/ch (1kHz, 1.0% THD, 8 ohms, DIN) Total Harmonic Distortion 0.05% Intermoduration Distortion (60 Hz:7 kHz) 97.9MHz search , Low Freq. - 97.9MHz search) 13 AM Section * Necessary measurement equipment : AM Signal Generator, Audio Signal Analyzer, Dummy Load, Oscilloscope, D

5、igital Volt Meter (DVM) (A) VT adjust AM Signal Generator Setting 1. Adjust AM Frequency of RSX-1065 to 522KHz. (or 520KHz) 2. Connect (-) terminal of DVM with GND ( or chassis ) and connect (+) terminal with Jumper JW14 ( VT CHECK ) and mesaure voltage. ( Low Freq. VT) 3. IF not 1.1V1.3V, Adjust VT

6、 to 1.2V with RF BLOCK RED COIL (AM-OSC Coil). * In case of USA version, AM freq. range is 520KHz 1710KHz. So, adjust as below. at 520KHz, VT = 1.2V ( Low Freq. VT) (B) Output Level adjust AM Signal Generator Setting - Modulation : 30%- Audio Frequency : 400Hz- Radio Frequency : 603KHz (or 600KHz )

7、- Output Level : 100dB RSX-1065 Setting - AM Frequency : 603KHz (or 600KHz) 1. Turn AM Signal Generator Modulation ON 2. Adjust RSX-1065 AM Freq. to 603KHz (or 600KHz) and measure output level with Audio Signal analyzer. 3. If it is lower than 200mV , Adjust output level to maximum point with RF BLO

8、CK BLACK COIL ( AM-ANT ). ( recommand higher than 250mV ) 4. Set Generator RF & RSX1065s RF to 999kHz(or 1000kHz) and measure output level with Audio Signal analyzer. Adjust output level to maximum point with IF BLOCK YELLOW COIL (C) TUNED Level adjust AM Signal Generator Setting - Modulation : 30%-

9、 Audio Frequency : 400Hz- Radio Frequency : 999KHz (or 1000KHZ) - Output Level : 84dB RSX-1065 Setting - AM Frequency : 999KHz (or 1000KHz) 1. Turn AM Signal Generator Modulation ON ( Make sure if Output level is 84dB ) 2. If TUNED indicator does not turn on at higher than 8086dB(Generator output),

10、Adjust SVR01 ( AM-ADJ ) up to the moment where TUNED indicator tunrs OFF & ON again 3. Confirm if TUNED turns OFF when decreasing the output level of AM Signal Generator slowly from 84dB to 80dB. 4. Push RSX-1065 TUNE UP or DOWN button long at AM Signal Generator Output Level 84dB and start AUTO sea

11、rch. Confirm if search stops at AM Frequency 999KHz (or 1000KHz). 999KHz(or 1000KHz) search , Low Freq. - 999KHz(or 1000KHz) search Power Amplifier Idling Adjustment Method * Necessary measurement equipment :Digital Volt Meter (DVM) After warm-up the Heat-Sinker (appolox. 30 centigrade degree) 1. Co

12、nnect the terminal of DVM to each TP points of the TP801 to TP805 on the Amplifier 2 PCB 016 X-1311A00. 2. Adjust each time Semi-Fixed VR of VR801 to VR805 on the Amplifier 1 PCB 016 X-1311A00. Adjust to DC4 mV. 14 1 Procedure of RSX-1065 software upgrade *Note : This procedure is made by translatio

13、n of Windows 98 version. So some of menu or option name may not be matched with some versions of Windows 98. First of all, User should have the new software file (via internet download) before preceding the software up-grade process. 1. Power RSX-1065 off. 2. Remove all of connections between RSX-10

14、65 and other equipments. 3. Connect RSX-1065 and PC with RJ45/DB9 cable. RJ45 jack should be connected to COMOUTER I/O port in RSX-1065 rear panel. DB9 jack will be connected to PC serial port (ex. COM1 or COM2,). 4. Switch down the SOFTWARE UPGRADABLE key to ON in RSX-1065 rear panel. 5. Open Hyper

15、Terminal program in Windows 98 (Program / Supplement Program / Communication / HyperTerminal) 6. Input name and select icon to use for connection in connection explanation dialogue box and click O.K. 7. Connection object dialogue box appears. Select modem(N) to use for connection. For example, if DB

16、9 cable is connected to COM1 serial port of PC, select COM1. 8. Selected serial port registration dialogue box appears. Select value or option per item as follows. *Bit per second (B) : 19200 *Data Bit (D) : 8 *Parity (P) : None *Stop Bit (S) : 1 *Flow Control (F) : None *And click O.K. 9. Click Fil

17、e (F) and click Property (R) in file menu of HyperTerminal. 10. Select setup. 11. In set up dialogue box, select options per item as follows. *Function Key : Terminal Key(T) *Backspace function: Ctr+H(C) *Emulation: VT100 *Telnet Terminal: VT100 *Back scroll buffer line : 500 *And click ASCII Setup

18、(A) *Select (A) & (W) at ASCII receiving section, Click O.K *Click O.K 12. Power RSX-1065 on and then options message appears in HyperTerminal screen. In the message, select number 1. Erase of current software begins. 13. When erasing finishes, download file message appears. Select Text file sending

19、 (T) in Transmission menu (T)of HyperTerminal and text file sending dialogue box appears. 14. Change the finding file format from (*.TXT) to (*.*) format, and find the new software which is for up-date.( *. Bin) format. 15. Double-click new software file. The extension of software file name is bin (

20、ex. xxx.bin). Then software upgrade begins. 16. When the upgrade finishes, check message appears. In the message, compare received data checksum with rom checksum. If they are same, the upgrade is done correctly. 17. Power RSX-1065 off and switch up the SOFTWARE UPGRADABLE key to Off in the rear pan

21、el. 18. Disconnect the cable between PC and the RSX-1065. 19. Power RSP-1066 on and set the default setting on the OSD screen menu with connecting a TV monitor. And confirm if the software version is upgraded. 15 Disassembly List 1014 TD3-08A00UPPER COVER51 024 SE2408PTB1-0260 FAN 2011 TD3-01B00H/S

22、PANEL52 019 4TSH-19#2FOOT 3013 TD4-11A00SUPPORT SIDE (2EA)53 016 E-1325A00TUNER PCB 4013 SG4-14D00SUPPORT B (2EA)54 071 4TVL-7#12CYLINDER BUSH H=35 5071 4TVL-8#7KARA SCREW (8EA)55 013 TD3-15A00PCB SUPPORT-A(2EA) 6017 TD3-03A00H/S BOARD L56 013 TD3-16A00PCB SUPPORT-B 7017 TD3-04A00H/S BORAD R57 067 C

23、-4493A00S/P TER 4P R,B,B,R 8013 TD4-10A00SUPPORT H/S (2EA)58 067 4TR-3222#1S/P TER 2P 9034 436302122031POSISTOER59 067 C-4493A01S/P TER 4P BU,BK,BK,BU 10 034 OP 62-80-5THERMAL SENSOR 60 066 4TR-2964#10RCA JACK 3P(Y), VIDEO 11 013 TD4-20A00SENSOR BKT 61 066 C-4604A02RCA JACK 3P, S-VHS 12 071 4TVL-8#4

24、KARA SCREW (10EA) 62RCA JACK 6P(WWW,RRR) 13 071 4TVL-8#10KARA SCREW (6EA) 63RCA JACK 3P(B,B,B) 14 019 TO 3PMICA 64RCA JACK 4P(WW,RR) 15 033 C3856-OPYTR (10EA) 65RCA JACK 9P(G,B,R) 16 033 A1492-OPYTR (10EA) 66 JACK 2P(B,B) 17 033 C4381-OYTR (5EA) 67 066 SY010-8P/KRJ 45 18 C 4137TR (5EA) 68RCA JACK 4P

25、(BB,BB) 19 033 A1667-OYTR (5EA) 69DIGITAL OPTICAL OUT 20 012 TB3-16A00KNOB 44F 70RCA JACK 2P(B,B) 21 012 TB3-17A00KNOB 13F(2EA) 71DIGITAL OPTICAL INPUT 22 012 RV4-09A00PUSH BUTTON 72 013 4TTU-13SUPPORT PCB(2EA) 23 011 FP-527SUB PANEL 73 015 RP-377REAR CHASSIS 24 015 TD3-06A00FRONT CH 74 069 C-4629A0

26、1AC IN LET 25 019 4TR-1083B#7FELT 51FX9F 75 019 RV4-10A00POWER BUTTON RING 26 019 4TR 1083B#6FELT 20FX9F(2EA) 76 019 C-4754A00KNOB RING 27 070 KN9ZKNUT (3EA) 77 014 4TQS-7#9PANEL WINDOW 28 070 W9NIWASHER (3EA) 78 014 C-4462A09FILTER BORAD 29 019 TD4-14A00INSULATION SHEET 79 012 TB3-18A00TACT BUTTON

27、16KEY(2EA) 30 061C-4176A08POWER S/W 80 013 TD4-12A00SERVICE MASK BORAD 31 035 HNR22ML02FIP 81 019 C-4779A00PT RUBBER 121F(75inF) 32 031 SBX3010-52BREMOTE SENSOR 33SPONGE 34 056 C-4678A01VR MAIN 35 056 C-4678A02VR TONE (2EA) S1 071 WB4X8BK 36 071 4tvl-7#23CYLINDER BUSH(4EA) S2 071 BTV3X8BK 37 061 C-4

28、679A01TACT S/W S3 071 MO3X8BK 38 013 TD3-07A00HOLDER SUB PANEL S4 071 MB4X8NI 39 013 TD3-17A00SUPPLY PCB BRACKET S5 071 NSM3X16ZK 40 017 C-4682A03REG TR H/S H=60(2EA) S6 071 BTV3X8NI 41 017 C-4682A02REG TR H/S H=45 S7 071 MB3X6NI 42 069 C-4372A00AC OUT LET 2P S8 07NSM3X0ZK 43 018 TD3-09A00BODY CH S9

29、 071 NSM3X12ZK 44 022 T-1082N03SUB PT EIS10 071 MB3X6NI 45 071 RE4-11A05SCREW BOLT KIT S11 071 NSM4X30NIFix FAN 46 013 RE4-07A02PT SUPPORT S12 071 NSM3X6ZK 47 019 4TPK-17PT RUBBER 110F S13 071 NSM4X8NI 48 022 T-1080U02SUB TRANSFORMER EI S14 071 CTB4X20NI 49 013 RV4-08B00PT SUPPORT S15 071 PTV3X8BK 5

30、0 013 TD4-18A00CE PCB SUPPORT SCREW DESCRIPTIONPARTS NO.NO.DESCRIPTIONPARTS NO.NO. 16 Disassembly Diagram 17 Wiring Diagram 16 18 PCB Assembly - 1/9 Front PCB 016 E-1310A00 FIP PCB 016 E-1309A00 Top side view FIP PCB 016 E-1309A00 Bottom view Speaker Terminal PCB 016 E-1314B00 RSX-1065v02 19 B PCB A

31、ssembly - 2/9 Input PCB 016E-1315C00, SUB PCB 016X-1346A00 016E-1315C00 Top View RSX-1065 v02 016E-1315C00 Bottom View 016X-1346A00 Bottom View Top View 20 PCB Assembly - 3/9 Digital 1 PCB 016E-1312B00 RSX-1065v02 Top View Bottom View 21 PCB Assembly - 4/9 Digital Board - 2 Top ViewDigital Board - 2

32、 Bottom View 22 PCB Assembly - 5/9 Video PCB 016 E-1316B00 RSX-1065v02 Moved parts: R1116, C1060 Added pats C1072 C1083,R1170 Top View Bottom View 23 PCB Assembly - 6/9 Amplifier PCB 016 X-1311A01-02 24 PCB Assembly - 7/9 Tuner PCB 016 E-1325A00 Top Side View Tuner PCB Bottom View 25 PCB Assembly -

33、8/9 Power Supply PCB 016 X-1317B01-04Top View RSX-1065v02 26 PCB Assembly - 9/9 Power Supply PCB 016 X-1317B01-04Bottom View RSX-1065v02 27 Block Diagram 28 Schematic Diagram - 1/13 29 Schematic Diagram - 2/13 30 Schematic Diagram - 3/13 Digital 1 PCB (1/3) 016E-1312B00 RSX-1065 v02 31 Schematic Dia

34、gram - 4/13 Digital 1 PCB (2/3) 016E-1312B00 RSX1065 v02 32 Schematic Diagram - 5/13 Digital 1 PCB (3/3) 016E-1312B00 RSX-1065 v02 33 Schematic Diagram -6/13 Digital Board -2 (1/2) 34 Schematic Diagram - 7/13 Digital Board -2 (2/2) 35 Schematic Diagram -8/13 FIP Circuit 36 Schematic Diagram -9/13 Fr

35、ont Circuit CXP811P24Q (OTP) CXP81120-123Q 37 Schematic Diagram -10/13 Input/Zone2/Component Video Circuit 38 Schematic Diagram - 11/13 Power Supply Circuit (US Version only) 39 Schematic Diagram-12/13 Speaker Terminal Circuit 016 E-1314B00 Tuner BoardE-1325B RSX-1065v02 40 ADDED DELETE Schematic Diagram -13/13 Video PCB 016 E-1316B00 RSX-1065v02 41