Infinity-PS410-sub-sm 电路图 维修手册.pdf

《Infinity-PS410-sub-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Infinity-PS410-sub-sm 电路图 维修手册.pdf（19页珍藏版）》请在收音机爱好者资料库上搜索。

1、 PS Series PS Series PS410 Subwoofer PS410 Subwoofer SERVICE MANUAL Infinity Systems Incorporated 8500 Balboa Blvd. Released 2010 Northridge, CA. 91329 Rev0 8/2010 Discontinued XXXX RadioFans.CN 收音机爱 好者资料库 - CONTENTS - BASIC SPECIFICATIONS .1 DETAILED SPECIFICATIONS.2 PACKAGING.4 CONTROLS AND CONNEC

2、TIONS.5 OPERATION.7 EXPLODED VIEW/PARTS LIST .8 TEST SET UP AND PROCEDURE.9 BLOCK DIAGRAM.10 ELECTRICAL PARTS LIST (120v) .11 PCB DRAWINGS.14 SEMICONDUCTOR PINOUTS.16 SCHEMATICS (120v).17 Basic Specifications PS410 Powered Subwoofer Frequency Response: 27Hz 150Hz (3dB) Maximum Amplifier Output: 300

3、Watts RMS; 500 Watts Peak (20Hz 150Hz with no more than 0.1% THD) Crossover Frequencies: 50Hz 150Hz, 24dB/octave, continuously variable Driver: 10 (254mm) MMD Dimensions (H x W x D): 15-3/4 x 12-1/2 x 16-1/2 (with grille) (400mm x 318mm x 419mm) Weight: 38.6 lb (17.6kg) Infinity continually strives

4、to update and improve existing products, as well as create new ones. The specifications and construction details in this and related Infinity publications are therefore subject to change without notice. 1 PS410 RadioFans.CN 收音机爱 好者资料库 Primus PS410150W Powered Sub Amp LINE VOLTAGEYes/NoHi/Lo LineNom.

5、UnitNotes US 120vac/60HzYes108-132120VrmsNormal Operation EU 230vac/50-60HzYes207-253230VrmsNormal operation, MOMS required ParameterSpecificationUnit QA Test Limits ConditionsNotes Amp Section Type (Class AB, D, other)Dn/an/a Load Impedance (speaker)4Ohmsn/aNominal Rated Output Power (120VAC)150Wat

6、ts145Domestic version only 120 VAC-60 Hz Rated Output Power (230VAC)150WattsEU Version only 230 VAC-50-60 Hz AVG RMS Dynamic Power210Watts200 Average RMS power, 3/20 Cycles 50 Hz, Driven 6dB above its input sensitivity sensitivity, average of the first 4 consecutive peaks THD Rated Power0.5%122K fil

7、ter THD 1 Watt0.2%0.322K filter DC Offset10mV-DC30Sub amp output Damping factor50DF35Measured at amplifier board Measured at the speaker cable. 150 Watts THD LP T 15 Minutes Power on Delay time3sec.4AC Power Applied Transients/Pops ATO Transient0.5V-peak0.5V Sub amp output Amplifier activated by sig

8、nal presence at the Line input Turn-on Transient0.5V-peak0.8V Sub amp outputAC Line cycled from OFF to ON 2 PS410 RadioFans.CN 收音机爱 好者资料库 ParameterSpecificationUnit QA Test Limits ConditionsNotes Turn-off Transient0.5V-peak0.8V Sub amp outputAC Line cycled from ON to OFF Efficiency Efficiency60%58Te

9、st conducted at rated power 150WNominal Line voltage Efficiency at 1/8 of rated power38%37Test conducted at 18.75 WRMSNominal Line voltage-Rated impedance 4 Ohms Off state input power16Watts18Nominal Line voltage RED LED Stand-by Input Power24Watts26 nom. line voltage Maximum allowable input power u

10、nder nominal Input voltage and frequency, HOT or COLD operation.LED GREEN no signal applied Power Cons. rated power250Watts260 nom. line voltage150 Watts 4 Ohms nominal line voltage Protections Short Circuit Protection YESfunctional Direct short at output Amplifier should resume operation after shor

11、t circuit condition removal Thermal Protection YESfunctional 1/8 max unclipped Power at 1.06 times the input voltage Temperature rise in accessible metal parts should not exceed 35K rise for domestic version or 30K rise for European versions (refer to requirements sheet). DC Offset ProtectionYES-DC

12、present at Speaker Out leads Design must insure no Offset at the speaker output under any operating condition including abnormal operation Line Fuse Rating USA-Domestic 2Amps2Type-T or Slo Blo-250 VInternal fuse with UL/SEMKO rated holder EU1.25Amps1.25 Type-T or Slo Blo-250 V, Low Breaking capacity

13、 Internal fuse with UL/SEMKO rated holder 3 PS410 4 PS410 PS210 (120V) Rear Panel CONTROLS ANDCONNECTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CROSSOVER FREQUENCY LEVEL LINE LEVEL IN PHASE MinMax LR For LFE use L or R Green: On Red: Standby 50Hz 0 80Hz 150Hz POWER ON LFENORMAL 180 120V 60Hz OF

14、F WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. AVERTISSEMENT: POUR PRVENIR LES RISQUES DINCENDIE OU DE CHOC LECTRIQUE, VITER DEXPOSER CET APPAREILA LA PLUIE OU A LHUMIDIT. NRTL/C CSA 22.2 UL1492 Subwoofer-Level Control LFE/Normal Selector

15、Phase Switch Crossover Adjustment Line-Level/LFE Input Power Switch Status LED Primus PS210 OM 9/27/06 9:58 AM Page 6 5 PS410 SYSTEMCONNECTIONS If your receiver/processor does not contain a Dolby Digital or DTS processor but has subwoofer outputs: Set line-level/LFE switch to “Normal.” NOTE: If your

16、 receiver/processor has only one sub out,you may use either the L or R input. If you have a DolbyDigital or DTSreceiver/processor with a low-frequency effects (LFE) or subwoofer output: LR CROSSOVER FREQUENCY LEVEL LINE LEVEL IN PHASE MinMax LR For LFE use L or R Green: On Red: Standby 50Hz 0 80Hz 1

17、50Hz LFENORMAL 180 SUBWOOFER OR LFE OUTPUT CROSSOVER FREQUENCY LEVEL LINE LEVEL IN PHASE MinMax LR For LFE use L or R Green: On Red: Standby 50Hz 0 80Hz 150Hz LFENORMAL 180 Set LFE/Normal switch to “LFE.” Primus PS210 OM 9/27/06 9:58 AM Page 7 6 PS410 OPERATION Power On Plug your subwoofersAC cord i

18、nto a wall outlet.Do not use the outlets on the back of the receiver. Initially set the Subwoofer-Level Control to the “min”position. Turn on your sub by pressing the Power Switch on the rear panel.Turn on your entire audio system and start a CD or movie soundtrack at a moderate level. Auto On/Stand

19、by With the Power Switch in the ON position,the Status LED on the back panel will remain lit in red or green to indicate the On/Standby mode of the subwoofer. RED = STANDBY (No signal detected,Amp Off) GREEN = ON (Signal detected,Amp On) The subwoofer will automatically enter the Standby mode after

20、approxi- mately 10 minutes when no signal is detected from your system.The subwoofer will then power ON instantly when a signal is detected.During periods of normal use,the Power Switch can be left on.You may turn off the Power Switch for extended periods of nonoperation,e.g.,when you are away on va

21、cation. Adjust Gain Turn your Subwoofer-Level Control up to the halfway position.If no sound emanates from the subwoofer,check the AC-line cord and input cables.Are the connectors on the cables making proper contact? Is the AC plug connected to a “live”receptacle? Has the Power Switch been pressed t

22、o the “On”position? Once you have confirmed that the subwoofer is active,proceed by playing a CD,record or cassette. Use a selection that has ample bass information. Set the overall volume control of the preamplifier or stereo to a comfort- able level.Adjust the Subwoofer-Level Control until you obt

23、ain a pleasing blend of bass.Bass response should not overpower the room but rather be adjusted so there is a harmonious blend across the entire musical range.Many users have a tendency to set the subwoofer volume too loud,adhering to the belief that a subwoofer is there to produce lots of bass.This

24、 is not entirely true.A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard.However,overall balance must be maintained or the music will not sound natural.An experienced listener will set the volume of the subwoofer so its impact o

25、n bass response is always there but is never obtrusive. Phase Control The Phase Switch determines whether the subwoofer speakers piston-like action moves in and out with the main speakers,0,or opposite the main speakers,180.Proper phase adjustment depends on several variables such as room size,subwo

26、ofer placement and listener position. Adjust the phase switch to maximize bass output at the listening position. Crossover Adjustment The Crossover Adjustment Control determines the highest frequency at which the subwoofer reproduces sounds.If your main speakers can comfort- ably reproduce some low-

27、frequency sounds, set this control to a lower frequency setting, between 50Hz and 100Hz.This will concentrate the subwoofers efforts on the ultradeep bass sounds required by todays films and music.If you are using smaller bookshelf speakers that do not extend to the lower bass frequencies,set the Cr

28、ossover Adjustment control to a higher setting,between 120Hz and 150Hz. NOTE: This control will have no effect if the LFE/Normal Selector is set to LFE.If you have a Dolby Digital or DTS processor/receiver,the Low-Pass Frequency is set by the processor/receiver.Consult your owners manual to learn ho

29、w to view or change this setting. MAINTENANCE ANDSERVICE The enclosure may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. The grille may be gently vacuumed.Stains may be removed with an aerosol cleaner,following its instructions.Do not use any solvents on the grille. All w

30、iring connections should be inspected and cleaned or remade periodically.The frequency of maintenance depends on the metals involved in the connections,atmospheric conditions,and other factors, but once per year is the minimum. In the event that your subwoofer ever needs service,contact your local I

31、nfinity dealer or distributor,or visit for a service center near you. Primus PS210 OM 9/27/06 9:58 AM Page 8 7 PS410 8 PS410 PS410 sub Test Set Up and Procedure SYSTEM AURAL SWEEP TEST Equipment needed: Function/signal generator/sweep generator Integrated Amplifier Multimeter Speaker cables General

32、Unit Function (UUT = Unit Under Test) Switches/knobs on the amplifier faceplate: Crossover Frequency Adjust full CW (Max) Phase switch either position Normal/LFE switch - Normal 1. From the signal generator, Connect both right and left line level inputs (RCA jacks) to signal generator and UUT. Use Y

33、-cable if necessary from mono source. 2. On the amplifier, turn the LEVEL control full Counterclockwise (Min). 3. Turn on generator, adjust to 75mV, 50 Hz. 4. Plug in UUT; turn the power switch ON. Turn LEVEL control full Clockwise (Max). 5. LED (on amp panel) should now be Green; immediate bass res

34、ponse should be heard and felt from rear port tube opening. Sweep Function 1. Follow steps 1-5 above, using a sweep generator as a signal source. 2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are hea

35、rd, remove woofer and test. Driver Function (Woofer) 1. Remove woofer from cabinet; detach + and - wire clips. 2. Check DC resistance of woofer; it should be 3.4 ohms10%. 3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal ge

36、nerator. Turn on generator and adjust so that speaker level output is 5.0V. 4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises. 9 PS410 10 PS410 PS410 Electrical Parts List Part number Qty DescriptionReference Designator PREMAP/MAIN/POWER PCB Cap

37、acitors 034-330525-300ZR1GR Electrolytic cap. 33uF/25V M (R)0511 P:5C1 033-680464-270ZS1GS NPE Cap. 印ELYTONE 6u8/100V K10 (R)1020 GNEC72 032-100484-200ZS1GS END Mylar cap. 1uF/250V K P:15C70, 033-470464-270ZS1GS NPE Cap.(印ELYTONE)1K 4u7/100V K10 (R)1015 GNEC73 031-100343-100ZS1GS SMD Cap. 100pF/50V

38、J 0805 NPO C58 034-220525-301ZS2GS Electrolytic cap. 22uF/25V M (R)5x11 P:5 C50,53 031-560243-100ZS2GS SMD Cap. 56pF/50V J 0805 NPO C57,61 031-220243-103AZ1GS SMD Cap. 0u022/50V J 0805 X7R C84, 031-100344-100ZS17 GS SMD Cap. 0u1/50V K 0805 X7R C42-44,46-49,52,55,60,63,71,74,77,100,101,80, 031-100244

39、-100ZS4GS SMD Ceramic cap. 0u01/50V K 0805 X7R C45,51,66,67, 034-470515-307ZR1GR Electrolytic cap.LOW ESR 85 47uF/16V M (R)0511 P:5 C65 031-100344-100ZS1GS SMD Cap. 0u1/50V K 0805 X7R C54 034-100625-300ZS1GS Electrolytic cap. 100uF/25V M (R)6.3x11 P:5C64 031-470244-102ZS2GS SMD Cap. 0u047/50V K 0805

40、 X7R C62,59 031-560343-102ZS1GS SMD Cap. 560pF/50V J 0805 NPO C56 034-330615-300ZS1GS Electrolytic cap. 330uF/16V M (R)0812 P:5 C78 031-100344-100AZ2GS SMD Cap. 0u1/50V K 0805 X7R C81,82 035-100393-301ZR2GR Mylar cap.(ESK TYPE) 0u1/63V J P:5 PN:ESK063S10JTC28,2A, 035-220393-300ZR1GR PE Cap. 0u22/63V

41、 J P:5 C27, 034-470415-301ZS1GS Elect. Cap. 4u7/50V M (R)0511 P:5 C2 034-100525-300ZS3GS Electrolytic cap. 10uF/25V M (R)0511 P:5 C35,237,238, 031-100244-100ZS2GS SMD Ceramic cap. 0u01/50V K 0805 X7R C5,10 031-100343-100ZS2GS SMD Cap. 100pF/50V J 0805 NPO C16,36 031-100344-100ZS1GS SMD Cap. 0u1/50V

42、K 0805 X7R C11 031-100384-100RZ2GS SMD Cap. 0u1/250V K 1206 X7R C3,7 031-220243-103AZ1GS SMD Cap. 0u022/50V J 0805 X7R C40 031-220344-100ZS5GS SMD Cap. 220pF/50V J 0805 NPO C14,15,20,21,19 031-330244-100ZR1GR SMD Cap. 0u033/50V K 0805 X7R C33, 031-680444-102ZR2GR SMD Cap. 6800pF/50V K X7R 0805 C32,3

43、4, 032-270343-301ZS3GS Mylar cap. (MP) 0u27/63V J P:5 C29,26,25 032-820244-200ZR1GR Mylar cap. 0u082/100V K (R)C30 034-220515-302ZR2GR elect. Cap. 22uF/16V M (R)0511 P:5 C39,75 034-220525-301ZS4GS 22uF/25V M (R)5x11 P:5 C4,9,41,76 034-330615-300ZS1GS 330uF/16V M (R)0812 P:5 C12 034-330780-300ZR2GR 8

44、5 SNAPIN 3300uF/80V M (R)22x48C6,8 034-470515-200ZR1GR 47uF/16V M (R)0511 P:2.5C37 039-100384-100ZR1GR Safety cap. (0u1/250V) .1K275VACx2 18x6x12mmCXAC1 034-100615-301ZS1GS electrolytic cap. 100uF/16V M (R)0611 P:5 C83 031-100344-100ZS2GS SMD Capacitor 0u1/50V K 0805 X7R C102,103, 031-100444-104ZR1G

45、R SMD Capacitor 1000pF/50V K 0805 X7R C104 Resistors 024-100398-120ZR1GR SMD Resistor 100R 1/8W J 0805 R62 020-220497-120ZR1GR Carbon Resistor 2K2 1/4W J R11 024-100298-120ZR2GR SMD Resistor 10R 1/8W J 0805 R81,82 021-100401-120ZR1GR MOF Resistor 1K 1W J INK MO-100R103 024-470498-120ZR2GR SMD Resist

46、or 4K7 1/8W J 0805 R85,86 022-500003-020ZR1GR Resistor KNP 0R05 3WS J FK TYPER104 024-220798-120ZR1GR SMD Resistor 2M2 1/8W J 0805 R80 024-430498-120ZR1GR SMD 4K3 1/8W J 0805 R78 024-300498-120LZ1GR SMD 3K 1/8W J 0805 R105, 024-470598-120ZR1GR SMD 47K 1/8W J 0805 R107 024-220598-120ZR1GR SMD 22K 1/8

47、W J 0805 R118, 024-680498-120ZR6GR SMD 6K8 1/8W J 0805 R91 024-110598-100ZR1GR SMD 11K 1/8W F 0805 R98 024-200598-120ZR1GR SMD 20K 1/8W J 0805 R94 024-100698-120ZR2GR SMD 100K 1/8W J 0805 R3,112 024-100598-120ZR18 GR SMD 10K 1/8W J 0805 R2,74,75,84,88,89,97,106,113-117,119,120, 141,138,139, 11 PS410

48、 Part number Qty DescriptionReference Designator PREMAP/MAIN/POWER PCB 024-100498-120ZR7GR SMD 1K 1/8W J 0805 R79,83,92,95,96,110,145, 024-590498-100ZR1GR SMD 5K9 1/8W F 0805 R140, 024-270498-120ZR1GR SMD 2K7 1/8W J 0805 R73 024-442498-100ZR1GR SMD 4K42 1/8W F 0805 R128 024-200498-120ZR1GR SMD 2K 1/8W J 0805 R108 024-300598-120ZR1GR SMD 30K 1/8W J 0805 R131, 024-150598-100ZR2GR SMD 15K 1/8W F 0805 R132,133, 024-470698-120ZR2GR SMD 470K 1/8W J 0805 R129,130, 024-390598-120ZR1GR SMD 39K 1/8W J 0805 R77 024-470298-120ZR2GR SMD 47R 1/8W J 0805 R101,102 024-390498-120ZR1G