《EMT-240-rev-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《EMT-240-rev-sm 电路图 维修手册.pdf（19页珍藏版）》请在收音机爱好者资料库上搜索。
1、Instruction Manual EMT 240 Reverb Foil GERMANY BARCO-EMT CONTACT: BIRDGETTE HEBDING nee (ZIMMER) TELEPHONE: 0114978259060 RadioFans.CN 收音机爱 好者资料库 ATTENTION! The unit contains an additional protection against shock, in order to prevent any damages caused by shock or other impacts due to rough handlin
2、g in transit. Before operation please remove the shock protection in the following se- quence: Open one side of the housing - take the wrench of the accessories and loosen nuts at the lower wooden blocks until the bolts will release the inside housing - take of f laterally the squeezed upper blocks
3、- take off laterally the lower blocks. The inside housing should now swing freely in all directions. If shipment has to be made by you occasionally via carriers, such as railway, airfreight or forwarding agents, we would recommend in your own interest to re-mount the shock protection and to ship the
4、 unit only in its original packing. The shock protection and the packing is not necessary for transportation by car, truck or Broadcasting Van, provided the unit is handled with care during such transportation and when loading and unloading the equipment. 8. July 1977 Vo/sh/ge 1 RadioFans.CN 收音机爱 好者
5、资料库 You have acquired a precision instrument when you bought the EMT 240 Reverb Foil. It was de- signed for field use and is therefore made to withstand mechanical shock found under normal operating conditions. Do not subject the unit to excessive accellerations treat it with the same care with whic
6、h you would handle a tape recorder, for example. This will assure that the excellent performance specifications of the EMT 240 will be maintained for some time to come. Unpacking instructions and preliminary set-up You have just opened the outer packing case please read on before you unpack the unit
7、 any further. 1. Remove the foam cushions on top of and on the left and right of the inner carton. Check to see that all of the accessories in the plastic covered boards correspond to the list on page 4. 2. Carefully lift out the inside carton. Do not lay the unit on its side under any circumstances
8、! 3. Open inside carton. 4. ATTENTION! The unit contains an a d d it io n a I protection against shock, in order to prevent any dam- ages caused by shock or other impacts due to rough handling in transit. Before operation please remove the shock protection in the following sequence: Open one side of
9、 the housing take the wrench of the accessories and loosen nuts at the lower wooden blocks until the bolts will release the inside housing take off laterally the squeezed upper blocks take off laterally the lower blocks. The inside housing should now swing freely in all directions. If shipment has t
10、o be made by you occasion- ally via carriers, such as railway, airfreight or forwarding agents, we would recommend in your own interest to re-mount the shock protec- tion and to ship the unit only in its original packing. The shock protection and the packing is not necessary for transportation by ca
11、r, truck or Broadcasting Van, provided the unit is handled with care during such transportation and when loading and unloading the equipment. 5. Locate unit at desired spot and connect electri- cally (page 8). Check proper line voltage set- ting! Turn unit on. Push the reverberation time button () f
12、or about 10 seconds. The unit is now ready for operation. 6. Save all packing materials! Re-ship only in the original packing. TRANSPORT IN UPRIGHT POSITION ONLY! 2 RadioFans.CN 收音机爱 好者资料库 Technical Description The Reverb Foil EMT 240 is a device for produc- ing reverberation. The principle involvin
13、g the use of a flat, tensioned plate for the creation of reverberation, which has been used for the past decades, has been re- tained in this new device. In the course of techni- cal improvement and the significant reduction in size, the material used in the vibrating plate has also been changed: Th
14、e EMT 240 Reverb Foil uses an electroplated gold foil of great purity (24 carat “coin gold”) with a thickness of only 18j.jm (.00071”) and 270 x290 mm (10.6”xl 1.4”) size. This foil is mounted in a frame under tension, excited by a driver, and sensed by a pick-up system. Changing the Reverberation T
15、ime The reverberation time is changed as before by bringing a damping device in close proximity to the foil. A vibrating foil such as this gives off energy to the surrounding air (sound field); by bringing an absorber more or less close to this sound field, energy is removed and the decay is damped
16、to a greater or lesser extent. This method not only has the advantage of damp- ing all frequencies equally and without erratic behavior (as may occur due to the complex input impedance of a mechanical system when damp- ing is done electrically by changing the imped- ance of the transducer), but it i
17、s also possible, using suitable means, to make this absorption frequency dependent and thereby to compensate the response of the reverberation time. These frequency dependent resistances are produced by openings in the damping plate. The picture shows slots in the actual damping material which serve
18、 this purpose. By varying the slot widths and the ratio between slot and damping surface, the required equalization is obtained. Remote Reverberation Time Control The damping plate may be moved by remote control. A complete description, including connec- tion means, is given on page 9. 3 4 5 6 7 Ali
19、gnment and Calibration IMPORTANT! A reverberation time of 2 seconds is to be set for all measurements! applicable from serial no.139 on The level alignment of the Reverb Foil EMT 240 may be undertaken in various ways, all of which produce the same result. 1.Alignment according to the “Braunbuch” spe
20、cifications 054 or V 54, only applicable to studio systems set up according to “IRT BRAUNBUCH” specifications: Feed a test signal of 1 kHz at 0 dBabs from a low impedance source oscillator (Ri 50 ohm) to the input. 1.2. Measure at the test jack using a high impedance volt meter or multi-meter (Ri 10
21、 kohm/volt); set INPUT potentiometer to produce reading of 0.245 V ( -10 dBabs) 1.3.Replace the test signal with a 1 kHz third octave white noise signal (e.g. part 1 of the Reverberation test tape) at a level of 0 dB. Adjust OUTPUT potentiometer so that 0 dB level is measured at the output of the un
22、it. Since the measuring instrument used influences the reading of white noise level, it is recommended that the same meter be used both for measuring input and output levels. 2.Alignment for studio systems using peak level indicators and any peak alignment levels: 2.2. 2.1.Feed a test signal of 2 kH
23、z at standard line level (e.g. +6 dB) from a low impedance source oscillator ( 50 ohm) to the input. Measure at the test jack using a volt- meter, peak level indicator or high impedance multi meter ( 0 kohm/ volt); set the INPUT potentiometer to produce a reading of 0.49 V ( -4 dB). 2.3.Replace the
24、test signal with a 1 kHz third-octave white noise signal (e.g. part 1 of the reverberation test tape) at standard line level (measured using studio peak indicator). Adjust OUTPUT potentiometer so that standard line level also appears on the peak indicator at the output of the unit. 3. Alignment usin
25、g vu meter: 3.1.Feed a test signal of 1 kHz at standard line level (e.g. +4, +6, or +8 dB) reading ZERO on your standard vu meter with proper vu range pad, to the units input. 3.2.Measure at the test jack using a high impedance volt meter or multi-meter ( 210 kohm/volt); set the INPUTpotentiometer t
26、o produce a reading of 0.245 V -10 dB abs8 Replace the test signal with a 1 kHz third- octave white noise signal (e.g. part 1 of reverberation test tape) or program material at standard line level measured using your standard vu meter) and adjust OUTPUT potentio- meter so that identical levels appea
27、r both at the input and output of each channel. To check the transmission characteristics and to facilitate alignment of the Reverb Foil EMT 240 we can supply a test tape (tape speed 15 ips (38.1 cm/s) equalization IEC/CCIR) which obviates the use of white noise genera- tor and third-octave filter.
28、This test tape has the following program: 1. Level alignment part Announcement; Third-octave band white noise; mid frequency 1 kHz; peak recording level; duration approxi- mately 2 min. Yellow leader 2. Frequency response part Announcement; Third-octave band white noise. 27 mid frequencies from 40 H
29、z - 12.5 kHz each with announce- ment; (duration each band 20 s) 14 dB under peak recording level. Alignment using sine wave signal is not possible since the reverb foil - as with every echo chamber - produces a multitude of closely spaced self-resonances and therefore would yield a highly frequency
30、 dependent output level. The frequency response is also best determined using third-octave white noise, but otherwise measured as usual: The output level as a function of frequency is measured with a constant level (-14 dB) at the reverberation unit input. The response should lie within the toleranc
31、e (low frequency cut-off filter in O dB position). In general it can be stated that minor deviations from the tolerances are not acoustically noticeable. A level recorder permits this measurement to be made using a sweep signal. The time constant of the recorder must be large enough so that the leve
32、l variations for small shifts in frequency are integrated. Further information regarding sweep frequency measurements may be found in the instructions for such equipment. The drive section of the Amplifier EMT 262 may have its low frequencies attenuated with three different time constants. The switc
33、h on the front panel of the amplifier is to be operated with a screw driver. The positions “0 dB” to “-24 dB” are shown in the response graph. Purpose of the low frequency cut-off: In a room the low frequency rever- beration components always have a longer reverberation time than the high. Often it
34、is desirable, from a produc- tion stand point, to reduce the low frequencies in the spectrum with respect to the high frequencies. In an echo chamber this requires structural changes, such as low frequency absorbers. In the EMT Reverberation Foil, the same effect is achieved with a multi-step, low f
35、requency cut-off filter. 9 10 11 12 13 Technical Data Reverberation time referred to 500 Hz Noise level at Tr = 2 5 Unweighted Signal-to- Noise ratio, rms Weighted Signal-to-Noise ratio, peak Minimum input signal for full drive Peak mea- sured vu measured Input impedance Maximum output level at 1 kH
36、z and Tr = 2 5 Usual reverberation return level Output source impedance Minimum load resistance Remote control Control voltage requirement Power requirement a) AC supply b) DC supply Weight Dimensions Subject to change. 0,7.55 65 dB 60dB 0.775V rms (0 dB) approx. 0.4 V rms ( 5 dB) 5 kQ balanced and
37、floating + 21 dBm for 1% THD 6.l0dB, relative to direct channel 40 Q balanced and floating 200 C) Silicone damped linear motor with control elec- tronics and position indicator. 24 VDC I 0.25 A switchable 200. 250 V or 100. l30V,50/60H25VA 24 VDC I 0.8 A 67 kg (148 lbs.) 640 x300X625 mm (251A” x 12”
38、 x 25”) (w x d x h) 14 15 16 17 RL: EMT 240 Alignment hints for units beginning with serial No. 195 (with Amplifier EMT 262 beginning with serial No. 23337). Beginning with the above named serial numbers, the drive aznplificrs have been coupled v.a pin 5 of the amplifier connector. The heretofore pu
39、blished level indications are still valid, but for calibration or operation with one amplifier inserted. There are three alignment possibilities: Input:0 dB, f= 1 kHz (third octave white noise) and T = 2 sec, produces at the Output: Test Jack Audio Output I.1 amplifier plugged into unit-10 dB0 dB II
40、.2 amplifiers plugged into unit, feed to only one input -.16 dB.3 dB III.2 amplifiers plugged into unit, both irputs fed from same source-10 dB+3 dB Note: Measure the level at the test jack using high impedance millivolt meter, R11OO kQ. Drive Amplifier: For a 0 dB nominal line level, the level cont
41、rol R I (in tile amplifier, ncctssible at the front panel) is to be adjueted so that a level of -13 dB is obtained at test point (C). The R128 potentiometer sets the limiter threshold. After nomiual align- ment: input = output = 0 dB, application of a +8 dB signal to the input hould result in 0.5 dB
42、 limiting at the output. The R 140 potentiometer determines the total amplificatioi as function of the trcnsducer sensitivity. 4 The potentiometer R 140 (in the reverb unit, 22 k at the drive trans- former) is to be adjusted to yield a level of -10 dB at the test jack. Pickup amplifier: The R 2 cont
43、rol (accessible at the front panel) determines tiie pick-up amplification. For nominal amplification of approx, 81 dB, the weighted noise level at the output should be -54 dB equivalent to an unweighted noise of approx. -62 dB peak Note: The front panel accessible gain controls are set to the foLLowin; scale marks for the standard factory alignment: input : 5 - 7 output: approx. 7 Kippenheim, May 27th, 1975 P1/sh 18
免费区 
