《Sharp-HTCN410DVH-hcs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sharp-HTCN410DVH-hcs-sm 电路图 维修手册.pdf（84页珍藏版）》请在收音机爱好者资料库上搜索。
1、HT-CN410DVH 1 HOME CINEMA WITH DVD Page SPECIFICATIONS.4 LASER BEAM SAFETY PRECAUTIONS .6 STANDARD NOTES FOR SERVICING.7 OPERATING CONTROLS AND FUNCTIONS.10 TROUBLESHOOTING.13 BLOCK DIAGRAMS.14 SCHEMATIC DIAGRAMS / ICS PIN VOLTAGE.16 WAVEFORMS.28 WIRING DIAGRAM.31 IC PIN FUNCTION DESCRIPTIONS.38 FL
2、DISPLAY.65 PARTS GUIDE SERVICE MANUAL No.S9502HTN410DV SHARP CORPORATION CONTENTS This document has been published to be used for after sales service only. The contents are subject to change without notice. HT-CN410DVHMODEL In the interests of user-safety (Required by safety regulations in some coun
3、tries) the set should be restored to its original condition and only parts identical to those specified be used. (for Middle East/ Africa/ Thailand) HT-CN410DVH Home Cinema with DVD consisting of HT- CN410DVH (main unit), CP-CN410F (front speakers), CP- CN410C (centre speaker), CP-CN410R (surround s
4、peakers) and CP-CN410SW (subwoofer). RadioFans.CN 收音机爱 好者资料库 HT-CN410DVH 2 CHAPTER 1. GENERAL DESCRIPTION 1 PRECAUTION FOR USING LEAD-FREE SOLDER 1. Employing lead-free solder Example: Indicates lead-free solder of tin,silver and copper. 2. Using lead-free wire solder When fixing the PWB soldered wi
5、th the lead-free solder,apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks. dedicated soldering bit,if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in yo
6、ur area. 3. Soldering and as it has poor solder wettability,you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB assoona
7、s you confirm the steady soldering condition. Lead-free solder contains more tin, and the end of the soldering bit may be easily corrected. Make sure to turn on and off the power of the bit as required. If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free
8、 solder. Clean the bit after every use of it. When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper. Be careful when replacing parts with polarity indication on the PWB silk. Lead-free wire solder for servicing Ref No.DescriptionParts No. PWB-A1CONTROL
9、PWB ASSY EARPHONE PWB ASSY STANDBY PWB ASSY MAIN PWB ASSY POWER PWB ASSY PWB-A2 PWB-A392LABE10530201 92LABE10510003 92LABE10504004 92LABE10530101 92LABE10530301 PWB-B PWB-C MAIN,DISPLAY,TERMINAL,SWITCH,POWER,JACK,TUNER,DVD,MICVIDEOOUT,CDCHANGERMOTOR(PWBONLY), LED PWB of this model employs lead-free
10、solder. The LF symbo lindicates lead-free solder,and is attached on the PWB and service manuals.The alphabetical character following LF shows the type of lead-free solder. As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 C, were commend you to use a As th
11、e melting point of lead-free solder (Sn-Ag-Cu) is about 220 C which is higher than the conventional lead solder by 40 C, RadioFans.CN 收音机爱 好者资料库 HT-CN410DVH 3 SAFETY PRECAUTION FOR SERVICE MANUAL AC POWER SUPPLY CORD Precaution to be taken when replacing and servicing the Laser Pickup. The AEL (Acce
12、ssible Emission Level) of Laser Power Output for this model is specified to be lower than Class 1 Require- ments. However, the following precautions must be observed during servicing to protect your eyes against exposure to the Laser beam. (1) When the cabinet has been removed, the power is turned o
13、n without a compact disc, and the Pickup is on a position outer than the lead-in position, the Laser will light for sev- eral seconds to detect a disc. Do not look into the Pickup Lens. (2) The Laser Power Output of the Pickup inside the unit and replacement service parts have already been adjusted
14、prior to shipping. (3) No adjustment to the Laser Power should be attempted when replacing or servicing the Pickup. (4) Under no circumstances look directly into the Pickup Lens at any time. (5) CAUTION - Use of controls or adjustments, or performance of procedures other than those specified herein
15、may result in hazardous radiation exposure. Material: AlGaAs/AlGalnP Wavelength: 785 nm/650 nm Emission Duration: continuous Laser Output: max. 0.6 mW Laser Diode Properties CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. WA
16、RNUNG: SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN GERT GEFFNET. NICHT IN DIE STRAHLUNG SCHAUEN ODER DIREKT MIT OPTISCHEN HILFSMITTELN BETRACHTEN. ATTENTION: RAYONS LASER VISIBLE ET INVISIBLE EN CAS DOUVERTURE. NE PAS REGARDER LE FAISCEAU DIRECTEMENT OU AVEC DES INSTRUMENTS OPTIQUES. 92LVPE1K32721
17、0 RadioFans.CN 收音机爱 好者资料库 HT-CN410DVH 4 SPECIFICATIONS l General l Amplifier l DVD player l Tuner As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures ind
18、icated are nominal values of production units. There may be some deviations from these values in individual units. Power sourceAC 230 V, 50 Hz Power consumption Power on: 45 W Power stand-by:0.6W Dimensions Width: 428 mm Height: 55 mm Depth: 360 mm Weight3.8 kg Audio input terminalsAnalogue input (I
19、N 1): RCA type 1 pair (L/R) Analogue input (IN 2): RCA type 1 pair (L/R) Audio output terminals Analogue output (OUT): RCA type 1 pair (L/R) Headphone: 16-50 ohms (recomended: 32 ohms) Digital output: Caoxial type x 1 Video output terminals S-video output: S-terminal 1 Video output: RCA type 1 Compo
20、nent video output: PB, PB, Y Video output terminalsSCART output: SCART terminal x 1 Output powerFront speakers: RMS: 42 W (21 W + 21 W) (DIN 45 324) Centre speaker: RMS: 21 W (DIN 45 324) Surround speakers: RMS: 42 W (21 W + 21 W) (DIN 45 324) Subwoofer speaker: RMS: 45 W (DIN 45 324) Signal systemP
21、AL/NTSC colour Supported disc types DVD (with the same region number on the back of the unit or ALL), SVCD, VCD, audio CD, CD-R, CD-RW, MP3 Video signalHorizontal resolution: 525 lines S/N ratio: 56 dB Audio signalFrequency characteristicsLinear PCM DVD: 20 Hz to 20 kHz (sampling rate: 48 kHz) 20 Hz
22、 to 20 kHz (sampling rate: 96 kHz) CD: 20 Hz to 20 kHz S/N ratio CD: 65 dB (1 kHz) Dynamic rangeLinear PCM DVD: 95 dB CD: 94 dB Total harmonic distortion ratio0.2 % maximum Frequency rangeFM: 87.5 - 108 MHz AM: 522 - 1620 kHz HT-CN410DVH 5 l Front speakers l Surround speakers l Centre speaker l Subw
23、oofer TypeFull range speaker system (magnetic shield) 7 cm speaker Maximum input power30 W Impedance4 ohms DimensionsWidth: 90 mm Height: 110 mm Depth: 100 mm Weight0.46 kg/each TypeFull range speaker system 7 cm speaker Maximum input power30 W Impedance4 ohms DimensionsWidth: 90 mm Height: 110 mm D
24、epth: 100 mm Weight0.45 kg/each TypeFull range speaker system 7 cm speaker Maximum input power30 W Impedance4 ohms DimensionsWidth: 90 mm Height:110 mm Depth: 100 mm Weight0.46 kg TypeSubwoofer system 13 cm Subwoofer Maximum input power60 W Impedance8 ohms DimensionsWidth:132 mm Height: 282 mm Depth
25、: 330 mm Weight2.8 kg HT-CN410DVH 6 LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30cm away from the pickup lens when the diode is
26、 turned on. Do not look directly at the laser beam. Caution: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. Driv
27、e Mecha Assembly Laser Beam Radiation Laser Pickup Turntable HT-CN410DVH 7 STANDARD NOTES FOR SERVICING How to Remove / Install Flat Pack-IC 1. Removal With Hot-Air Flat Pack-IC Desoldering Machine: (1)Prepare the hot-air flat pack-IC desoldering ma- chine, then apply hot air to the Flat Pack-IC (ab
28、out 5 to 6 seconds). (Fig. S-1-1) Fig. S-1-1 (2)Remove the flat pack-IC with tweezers while apply- ing the hot air. (3)Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to centre of the flat pack-IC and heat up. Then remove (glue
29、will be melted). (Fig. S-1-6) (4)Release the flat pack-IC from the CBA using twee- zers. (Fig. S-1-6) Caution: 1. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other p
30、arts from damage. (Fig. S-1-2) 2. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it. Hot-air Flat Pack-IC Desoldering Machine CBA Flat Pack-IC Tweezers Masking Tape Fig. S-1-2 With Soldering I
31、ron: (1)Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) Flat Pack-IC Desoldering Braid Soldering Iron Fig. S-1-3 (2)Lift each lead of the flat pack-IC upwar
32、d one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4) Fine Tip Soldering Iron Sharp Pin Fig. S-1-4 (3)Bottom of the flat pack-IC is fixed with glue to the CBA; when remo
33、ving entire flat pack-IC, first apply soldering iron to centre of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) (4)Release the flat pack-IC from the CBA using twee- zers. (Fig. S-1-6) With Iron Wire: (1)Using desoldering braid, remove the solder from all pins of the f
34、lat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) (2)Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. (3)While heating the pins using a fine tip soldering iron or hot air blower, pull up the wi
35、re as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5. HT-CN410DVH 8 (4)Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to centre of the flat pack-IC and heat up. Then remove (glue wi
36、ll be melted). (Fig. S-1-6) (5)Release the flat pack-IC from the CBA using twee- zers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damag
37、ed if force is applied. To Solid Mounting Point Soldering Iron Iron Wire or Hot Air Blower Fig. S-1-5 Fine Tip Soldeing Iron CBA Flat Pack-IC Tweezers Fig. S-1-6 2. Installation (1)Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install
38、a replacement flat pack-IC more easily. (2)The mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation. Then presol- der the four corners of the flat pack-IC. (See Fig. S- 1-8.) (3)Solder all pins of the flat pack-IC. B
39、e sure that none of the pins have solder bridges. Example : Pin 1 of the Flat Pack-IC is indicated by a mark. Fig. S-1-7 Presolder CBA Flat Pack-IC Fig. S-1-8 HT-CN410DVH 9 Instructions for Handling Semi-conductors Electrostatic breakdown of the semi-conductors may occurduetoapotentialdifferencecaus
40、edbyelectrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1M) that is properly grounded to remove any static electricity that may be charged on the body. 2. Ground for Workbench Be sure to place a conductive sheet or copper plate with proper
41、 grounding (1M) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing. CBA CBA Grounding Band Conductive Sheet
42、 or Copper Plate HT-CN410DVH 10 OPERATING CONTROLS AND FUNCTIONS n Main unit (front panel) 1.On/Stand-by Button 2.Disc Tray 3.Disc Tray Open/Close Button 4.Remote Sensor 5.Play or Pause Button 6.Chapter (track) Skip Down or Preset/Tuning Down Button 7.Chapter (track) Skip Up or Preset/Tuning Up Butt
43、on 8.Volume Up and Down or Speaker Level Adjust Buttons 9.Power Stand-by Indicator 10. Stop Button 11. Function Button 12. Speaker Level Mode Button 13. Headphone socket 14. Speaker Indicators (1) Left Front Speaker Indicator (2) Centre Speaker Indicator (3) Right Front Speaker Indicator (4) Left Su
44、rround Speaker Indicator (5) Subwoofer Indicator (6) Right Surround Speaker Indicator 15. DVD Indicator 16. JPEG Indicator 17. P - SCAN mode 18. Dolby Digital Signal Indicator 19. Play Indicator 20. Pause Indicator 21. SVCD/VCD/CD Indicator 22. MP3 Indicator 23. DTS Signal Indicator 24. Dolby Pro Logic/Pro Logic II Indicator 25. Stereo (2-ch) or FM Stereo Receiving Indicator 26. Title Indicator 27. Track Indicator 28. Chapter Indicator 29. Tuner Preset Indicator 30. Programme Indicator 31. S
免费区 
