RCA-Victor-Co-Inc-2-XF-932 电路原理图.pdf

《RCA-Victor-Co-Inc-2-XF-932 电路原理图.pdf》由会员分享，可在线阅读，更多相关《RCA-Victor-Co-Inc-2-XF-932 电路原理图.pdf（8页珍藏版）》请在收音机爱好者资料库上搜索。

1、MANUAL OF 1953 MOST-OFTEN-NEEDED RADIO DIAGRAMS Jgfe Hrt *U . rcaVictor * 2| * *-K HH 55 Receivers 2-XF-931, 2-XF-932, 2-XF-933, 2-XF-934, 2-XF-935, Chassis RC-1121A. Model 2-XF-91, using Chassis RC-1121, is similar to RC-1121A. Alignment continued on the next page. 收音机爱 好者资料库 RadioFans.CN MANUAL OF

2、 1953 MOST-OFTEN-NEEDED RADIO DIAGRAMS RCA Victor Receivers 2-XF-931, 2-XF-932, 2-XF-933, (Continued from preceding page) 2-XF-934, 2-XF-935, using Chassis RC-1121A. ALIGNMENT PROCEDURE Model 2-XF-91, Chassis RC-1121, is similar. ALIGNMENT INDICATORS: An RCA VoltOhrayst or equivalent meter is necess

3、ary for - - - - FUNCTION SWITCH IN AM POSITION measuring developed d-c voltage during FM alignment. Connec tions are specified in the alignment tabulation. An output meter is also necessary to indicate maximum audio output during AM alignment. Connect the output meter across the speaker voice coil.

4、The RCA VoltOhmyst can also be used as an AM align ment indicator, either to measure audio output or to measure A VC voltage. When audio output is being measured, the vol ume control should be turned to maximum. Adjust tone control to mid-position. SIGNAL GENERATOR: For all alignment operations, con

5、nect the low side oi the signal generator to the receiver chassis. Ii output measurement is used for AM alignment, the output of the signal generator should be kept as low as possible to avoid AVC action. If an FM sweep generator is used for FM alignment, adjust for 10.7 me. 0.4 me sweep. Connect os

6、cilloscope across C26, adjusting discriminator T6 top core for 10.7 me crossover, and T6 bottom core for balanced peaks. Peak separation should be approximately 330 kc. When aligning the other FM tuned cir cuits. connect oscilloscope lead through a 220K resistor to pin 1 of V5. Follow alignment tabl

7、e sequence, adjusting for maximum gain and symmetrical curves. Connect high side of sig. gen. to Sig. gen. output Pin No. 1 of V3 in series with .01 mfd. 455 kc. (mod.) Tap lug 4 on AM RF coil 1620 kc. (mod.) 1400 kc. Short wire placed near (mod.) loop for radiated signal 600 kc. (mod.) Turn radio I

8、 dial to I Quiet point at high freq. end Tube Socket Voltages Tube Type and Function VI 6BJ6 Adjust for peak output T4 bottom core (sec.) T4 top core (pri.) T2 bottom core (sec.) T2 top core (pri.) 4 ROO K. M03. C37 (ant.) _ Shortwire (mod.) M0D kc C1C-T (ri) placed near L6 (oc.) with loop ior 10,00

9、0 ohm 5 radiated resistor from C1C signal egg _ RF stator to gnd. _ (mod.) 600 kc- (rocking gang) L4 (RF) 6 with the 10.000 _ohms removed m Repeat steps 4. 5 and 6 until maximum _gain is obtained_ FM Alignment FUNCTION SWITCH IN FM POSITIONVOLUME CONTROL MINIMUMTONE CONTROL CENTER Plate Screen Connect high side of sig. Sig. gen. output Turn radio dial to Adjust for max. output 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 RadioFans.CN