RCA-Victor-Co-Inc-RC-1219B 电路原理图.pdf

《RCA-Victor-Co-Inc-RC-1219B 电路原理图.pdf》由会员分享，可在线阅读，更多相关《RCA-Victor-Co-Inc-RC-1219B 电路原理图.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。

1、VOLUME R-25, MOST-OFTEN-NEEDED 1965 RADIO SERVICING INFORMATION DOA /|OTOP Models RFG 20A, H, V, use Chassis RC-1219A.B V*vlvl Models RFG 25B, E, use Chassis RC-1219B 35169 itT iw um. 35170 2ND I f ANPL 35454 I 35454 2 Af AU”. AUCMO PMVCfl ALIGNMENT PROCEDURE Connect High Side of Signal Generator to

2、 Loop or piece of short wire placed near antenna for radioled signal Signal Gen. Output Dial Pointer Setting Adjust for Max Output 455 kc Gang fully open T4 (3rd l-F) T3 (2nd l-F) T2 (1st l-F) Repeal Stpi 1, 2, and 3 1620 kc Gang fully open Oscillator trimmer OB-T 1400 kc 1400 kc (rack gang if neces

3、sary) Anlenna Irimmer CIA-T 600 kc 600 kc (rock gang) Osc. cail Tl Repeal Steps 5, 6, and 7 USE PROPER ALIGNMENT TOOL FOR MAKING ADJUSTMENTS. CORES ARE EASILY BROKEN BY IMPROPER HANDLING, MAKING NECESSARY RE PLACEMENT OF ENTIRE COIL. .- 1 Rf 1 VOLTACCS MEASURED WITH 0LT0HMVST* mow mmin mould mold wi

4、thin lo% WITH MCW BATTIRV VOLUME CONTROL AT MM MUM N0 3HMAL IOOO ALL NTS STANCE VALUES Ht OHMS ALL CAPAOTAHCf VALUES LESS THAN 0.0 ARE m 1* THOSE ABOVE I 0 ARE IN /* EXCEPT AS NOTED CHASSIS REMOVAL 1 Remove tuning and volume knobs 2 Open case as explained under Battery Replacement 3 Remove three scr

5、ews securing chassis (Two at battery end of board and one at speaker end ) 4. Remove nut holding earphone jack (RC 1219B) or slide ear phone jack out of slot (RC 1219A). 5. Unsolder speaker wires if necessary (or remove clips holding speaker to case). 6 Unsolder battery wires if necessary 7 Lift boa

6、rd out of case. T0 SPEAKER WTERM-BD. YEL TO Jl EARPHDNE JACK 131 收音机爱 好者资料库 RadioFans.CN VOLUME R-26, MOST-OFTEN-NEEDED 1966 RADIO SERVICING INFORMATION RCA VICTOR Models RGG-17B, RGG-22A, N, U, RGG-25B, E, G Chassis RC-1219A, RC-1219B 35169 1ST I.F AMPL 35170 2ND I F AMFt ta 35820-2 AUDIO DRIVER _B

7、RCCM 35fi203(Ml f- 2.9 v lets 0O7v fla7IV ALIGNMENT PROCEDURE Connact High Sid* of Signal Generator to Signal Gen. Output Dial Pointer Setting Adjust for Max. Output T4 (3rd l-F) 455 kc Gang fully T3 (2nd l-F T2 (1st l-F Loop or piece of short wire Repeal Steps 1, 2, and 3 placed near anlenna for ra

8、diated 1620 kc Gang fuiiy open Oscillator trimmer C1B-T 1400 kc 1400 kc (rock gang if necessary) Antenna trimmer C1A-T 600 kc 600 kc (rock gang) Osc. coil T1 Repeat Steps 5. 6, and 7 35820-3(M) AUDIO OUWT .J-2O0HF V0LTAQE3 MEASURED WITHVOLTWRIYSr PROM ! BATH AY, SHOULD HOLD WITHIN 20% WITH NEW BATTE

9、RY, VOLUME COHTAOL AT MAXIMUM B HO SIGNAL K-lOOO ALL RESISTANCE VALUES IN OHMS ALL CAPACITANCE VALUES LESS THAN I.OAAE IN r THOSE ABOVE 1.0 AAE IN EXCEPT AS NOTED. F BOB IK A MATCHED PAlN ON VOL * S.CNOC =- (2 VMM T“ OVVSSSA) | LI-FtAAtTE ANTENNA ,*T LIA CHASSIS REMOVAL 1. Remove tuning and volume k

10、nobs. 2. Open case. 3. Remove three screws securing chassis. (Two at battery end of board and one at speaker end.) 4. Remove nut holding earphone jack (RC-1219B) or slide earphone jack out of slot (RC-1219A). 5. Unsolder speaker wires if necessary (or remove clips holding speaker to case). 6. Unsolder battery wires if necessary. 7. Lift board out of case. LI A/B I TO SPEAKER TERM SD. IWHT TO+8 ATT. r0 + 8ATT. to -BATT. Chassis Layout (Wiring Side) tZL-guS? SiSKrvP jjfflp *:B*s .f- 4 cie !i6Ts25,R1,1 -. x V t !*. %RZ? 1 C19 / / 112 收音机爱 好者资料库 RadioFans.CN