Westinghouse-Electric-Corp-V-2239-2 电路原理图.pdf

《Westinghouse-Electric-Corp-V-2239-2 电路原理图.pdf》由会员分享，可在线阅读，更多相关《Westinghouse-Electric-Corp-V-2239-2 电路原理图.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。

1、VOLUME R-16, MOST-OFTEN-NEEDED 1956 RADIO SERVICING INFORMATION Westingliouse CHASSIS V-2239-1, MODELS,H-523T4,H-524T4,H-525T4 (BLACK) (IVORY) (CORAL) CHASSIS V-2239-2,M0DELS,H-538T4,H-539T4,H-540T4 (BLACK) (IVORY) (CORAL) The V-2239-1 chassis is basically the same as the V-2239-2 chassis, except th

2、at a clock is used with the V-2239-2 chassis and not with the V-2239-1. In the V-2239-1 chassis the off-on switch is ganged with the volume control and in the V-2239-2 chassis the off-on switch is part of the clock mechanism. 50C5 is AlXMO OUTPUT OUTPUT TRANS. 1 , . , 30*_ 1 . ( GRN WIRE f TO U .WHI

3、TE WIRE %2au6*r ,/y I CLOCK MECHANISM J CIRCUITRY DIFFERENCE FOR V2239 C i r i t Al - I2AV6 f 3 _ 1 isocs5 -z * V 5V 93V ,?W Lt OSC. COIL C9-. 0 OSC. TRIM. Tl PRI TOP SEC. BOTTOM Zl CONSTRUCTION R4 VOLUME CLOCK CONTROL alignment It is rscommsnded that the chassis be isolated from the power line by m

4、eans of an isolation transformer. While making the following ad|ustments, keep the volume control set for maximum output and the signal generator ontenuated os much os possible. Connert VTVM across voice coil. Step I Connect Signal Generator 1 To: Stotor of tuning capacitor (A) through o200 mmfd. ca

5、p acitor ana low side to B-. 2. Radiated signal Radiated signal S I8T3 P 2 o o v g | 8 T uning Capac it or Adjust for Maximum Output Minimum capacity Top ond bottom slugs of Tl Minimum copacity Oscillator trimmer (D) 1400KC Antenno trimmer (B) 收音机爱 好者资料库 RadioFans.CN VOLUME R-17, MOST-OFTEN-NEEDED 1

6、957 RADIO SERVICING INFORMATION Westioghouse Models H-574T4, H-575T4, H-576T4, H-577T4, Using Chassis Assembly V-2239-2 ALIGNMENT While making the following adjustments, keep the volume control set for maximum output and the signal generator output attenuated to weakest useable signal level. Step Co

7、nnect Signal Generator to Signal Generator Frequency Radio Dial 1 Stator of ant. tuning capacitor (A) through a 200 mmf capacitor 455 kc* minimum capacity 2 Radiated signal 1625 kc. minimum capacity 3 Radiated signal 1400 kc. 1400 kc. Connect V.T.V.M. Across Voice Coil and Adjust for Maximum Output

8、Top and bottom slugs of T2 and T1 in order given Oscillator trimmer (D) Antenna trimmer (B) note: 1. ALL CAPACITANCE VALUES IN MFD AND AL RESlSTANCrVALUES IN OHMS UNLESS OTHERWISE STATED. 2. ALL VOLTAGES MEASURED FROM B USING A VTV.M. LINE VOLTAGE SET AT II? V A C READINGS SHOULD BE AS SHOWN 20%. 3.

9、 CHASStS GROUND rb common e- -4 I2AU6 CONVERTER I2AV6 OETISI AUDIO 50C5 audio output R4 2M I i VOLUME CONTR. 4 2 j zt - XJ | .005 :_A_6i 220 MMF T470K i 6.8M ii|, 250 _ MMF _5; HI-1 005 470K | S( t MMF 1 ; TO L, HITE GREEN r- i I-T-J m $ r/ CHASSIS GND. /+l COMMON B - - - ,.11 pg-j i C _s,v 5 j Prin

10、ted Board Servicing L-* | It * * To remove defective parts, apply the tip of the L“Tc,- ! Jb 7 l2AU6 soldering iron to the connection. Keep the sol- -C!-* T 4v 4 dering iron on the connection just long enough /l? -! * 3SW4 to melt the solder, then quickly brush away sol- 007 *! * der with a small gl

11、ue brush. After solder has f, . j sec. j * * been removed, separate connections. If the com- v. + aT+ 4 .1! 3 ponent has bent prongs, such as IP transformers, C4A 1 coils, tube sockets etc., straighten the prongs and cut as close to the board as possible, then heat connection and brush away all sold

12、er with , ,aAV8 , I H 4 sma11 Blue brush. ,4-/ 5Q5 . Por Quick replacement of parts, such as re- aov ssv sistors, capacitors etc., the original solder joint jti_ 3 5* lfc *mv need not be touched. If the leads of the defect- + . nixA-J-J-f-ti_ ,LUI ive part are long enough, the defective part may I w

13、ts be removed by clipping the leads near the body 95. of the defective component. The new part can be j. Bottom View soldered to the connecting wires removed from the original part. The printed board is held secure in the cabinet by a top and bottom channel molded into the cabinet. Located above the

14、 tuning shaft and concealed by the tuning knob is a single screw (No. 6/32-5/8”) which mounts the printed board to the front of the cabinet. To remove the printed board from the cabinet, remove the front control knobs then remove the screw mounting the printed board to the front of the cabinet. Remove the two self-tapping screws, interlock and back cover. The printed board can now be removed from the cabinet. Bottom View 163 收音机爱 好者资料库 RadioFans.CN