Aiwa-SX-STV10-Service-Manual 电路图 维修手册.pdf

《Aiwa-SX-STV10-Service-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-SX-STV10-Service-Manual 电路图 维修手册.pdf（4页珍藏版）》请在收音机爱好者资料库上搜索。

1、SPEAKER SYSTEM SX-STV10 S/M Code No. 09-99A-336-3N1 Y SERVICE MANUAL DATA SPECIFICATIONS Design and specifications are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 2 1 8Z-YS5-005-010 CABI,FR 2 8Z-YS5-001-010 PANEL,FR 3 8Z-YS5-002-010 PANEL,REAR 4 8Z-YS5-003-010 PANEL,DUCT 5 8Z-YS5-601-0

2、10 SPKR,W 160 8OHM 75W 6 8Z-NSY-003-010 CORD,BUSH 7 8Z-YS5-602-010 CORD,DIN5PIN MECHANICAL EXPLODED VIEW 1/1 REF. NOPART NO.KANRIDESCRIPTION NO. MECHANICAL PARTS LIST 1/1 Basic color symbolColorBasic color symbolColorBasic color symbolColor BBlackCCreamDOrange GGreenHGrayLBlue LTTransparent BlueNGol

3、dPPink RRedSSilverSTTitan Silver TBrownVVioletWWhite WTTransparent WhiteYYellowYTTransparent Yellow LMMetallic BlueLLLight BlueGTTransparent Green LDDark BlueDTTransparent Orange COLOR NAME TABLE RadioFans.CN 收音机爱 好者资料库 3 SPEAKER DISASSEMBLY INSTRUCTIONS Insert a flat-bladed screwdriver into the pos

4、ition indicated by the arrows and remove the panel. Remove the screws of each speaker unit andthen remove the speaker units. Remove the grill frame and four pieces of rubber caps by pulling out with a flat-bladed screwdriver. Remove the screws from hold where installed rubber caps. Insert a flat-bla

5、ded screwdriver into the position indicated by the arrows and remove the panel. Re- move the screws of each speaker unit and then remove the speaker units. Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Turn the speaker unit to counter- clockwise dir

6、ection while inserting a flat-bladed screwdriver into one of the hollows arround speaker unit, and then remove the speaker unit. After replacing the speaker unit, install it turnning to clock- wise direction unitil click sound comes out. Type.1 Type.3 Type.2 TOOLS 1Plastic head hammer 2(-) flat head

7、 screwdriver 3Cut chisel How to Remove the PANEL, FR 1.Insert the (-) flat head screwdriver tip into the gap between the PANEL, FR and the PANEL, SPKR. Tap the head of the (-) flat head screwdriver with the plastic hammer head, and create the clearance as shown in Fig-1. 2.Insert the cut chisel in t

8、he clearance, and tap the head of the cut chisel with plastic hammer as shown in Fig-2, to remove the PANEL, FR. 3.Place the speaker horizontally. Tap head of the cut chisel with plastic hammer as shown in Fig-3, and remove the PANEL, FR completely. Type.4 Fig-1Fig-2 Fig-3 How to Attach the PANEL, F

9、R Attach the PANEL, FR to the PANEL, SPKR. Tap the four corners of the PANEL, FR with the plastic hammer to fit the PANEL, FR into the PANEL, SPKR completely. 1? 2?3 RadioFans.CN 收音机爱 好者资料库 920074 Printed in Singapore 211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111 1 8Z-YS5-901-010 IB,Y (E,S,R,G,A,PE) BASS REF. NOPART NO.KANRIDESCRIPTION NO. ACCESSORIES/PACKAGE LIST