Bogen-BBF-Operation-Manual 电路图 维修手册.pdf

《Bogen-BBF-Operation-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Bogen-BBF-Operation-Manual 电路图 维修手册.pdf（1页珍藏版）》请在收音机爱好者资料库上搜索。

1、1A: BBS Installation 1. Install BBS back box on wall, making sure that the box is squarely mounted. Allow free access above box for AC wiring and above or below box for audio wiring. 2. Have power wiring run near upper right-hand corner where box will be mounted. 3. Secure box on wall with screws th

2、rough back holes (4 screws). Flush- and Surface-Mount Back Boxes Models BBF and BBS - Installation and Use Manual 1B: BBF Installation 1. Prepare mounting hole for BBF back box. Hole size should be 24-13/16 H x 14-5/16 W minimum opening with studs or mounting surfaces on each side. 2. Have power wir

3、ing run near upper right-hand corner where box will be mounted. 3. Install BBF back box in wall, making sure that the box is squarely mounted and the front sur- face flush with the finished wall. Use shims if necessary.Allow free access above box for AC wiring and above or below box for audio wiring

4、. 4. Secure box in wall with screws through side slots (4 screws). 5. With box positioned,install 4 additional screws in holes next to slots. 2: Junction Box Wiring 1. Supply AC power to unit through conduit,BX or ROMEX in accordance with local electrical codes. 2. Snap AC receptacle into junction b

5、ox (GND pin down) and connect wires as shown using wire nuts. 3. BBF - Install junction box in BBF and secure with four #6 x 3/8 screws. BBS - Install junction box in BBS and secure with four #6-32 x 3/8 screws and KEPS nuts. 50 Spring Street, Ramsey, NJ 07446, U.S.A. Tel. 201-934-8500, Fax: 201-934

6、-9832, Specifications subject to change without notice. 2005 Bogen Communications, Inc. Part No. 53-5599-01C 0507 4:Amplifier Installation 1. Mount amplifier on back box by aligning hinge pins and lowering into place. 2. Connect ground strap by inserting middle hinge screws through lugs of ground st

7、rap as shown in illustration.Ground strap must be installed to meet UL requirements. 5: Front Panel Mounting 1. Mount front panel (but do not tighten) with four #8-32 x 3/8 screws at top and bottom of panel. 2. Install two #8 x 3/8 screws on inside lips of door opening, then tighten all mounting scr

8、ews. Do not overtighten as U-clip will strip. 3. Check to see that door opens and closes correctly. 3: Preparations Before Installing Amplifier 1. Run all audio leads into wall box.The preferred arrangement is for output leads to enter through the top and input leads to enter through the bottom. Use

9、 knockouts as necessary.Make sure wires do not rest against sharp edges of box. 2. Install hinges (packed with amplifier) using 6 #8 x 3/8 screws. Do not install middle screws of lower hinge (used for ground strap connection - see 4). 3. Check to see that AC power is available at the outlet. BBF Jun

10、ction Box BBF BBS Ground Strap Output Input 3. Make necessary input and output con- nections (care should be taken to keep input and output leads separated as much as possible). 4. With power switch turned off, plug AC cord into side outlet on junction box. 5. Turn amplifier ON and check connections. 6. Secure amplifier using three #8-32 x 1/2 screws. RadioFans.CN 收音机爱 好者资料库