Bogen-HAA20-Operation-Manual 电路图 维修手册.pdf

《Bogen-HAA20-Operation-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Bogen-HAA20-Operation-Manual 电路图 维修手册.pdf（8页珍藏版）》请在收音机爱好者资料库上搜索。

1、54-2066-01 LIMITED WARRANTY Bogen warranties all headsets and amplifiers against defects in material or workmanship provided that the equipment has not been subjected to abuse or accident or altered in any way for two (2) years from the date of sale to the original purchaser. Any part of the equipme

2、nt covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our option, provided the product is shipped, insured and prepaid, to: Bogen Factory Service Department, 50 Spring St., Ramsey, NJ 07446, USA. The equipment will be returned

3、 to you freight prepaid. This warranty does not extend to any of our products that have been subjected to misuse, improper storage, neglect, accident, improper installation or have been modified or repaired in any manner that Bogen believes may affect the reliability of the product, or where the ser

4、ial number or date code has been removed or defaced. THE FOREGOING LIMITED WARRANTY IS BOGENS SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASERS SOLE AND EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR

5、 A PAR- TICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED. Bogens liability arising out of the manufacture, sale or supplying of products or their use or disposition, whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the product. In no event shall Bogen be l

6、iable for special, incidental or consequential damages (including, but not limited to, loss of profits, loss of data or loss of use damages) arising out of the manufacture, sale or supplying of products, even if Bogen has been advised of the possibility of such damages or losses. Products that are o

7、ut of warranty will also be repaired by the Bogen Factory Service Departmentsame address as above or call 201-934-8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service Department. All shipping charges, in addition to parts and labor

8、charges, will be at the owners expense. 50 Spring Street, Ramsey, NJ 07446, U.S.A. Tel: 201-934-8500, Fax: 201-934-9832, 2001 Bogen Communications, Inc. Printed in USA 0110 Specifications subject to change. U S E R G U I D E HAA20 TELEPHONY HEADSETAMPLIFIER Bogen 130% 9/26 10/5/01 11:08 AM Page 1 Ra

9、dioFans.CN 收音机爱 好者资料库 CONTENTS 1. Telephone cable 2. Rapid Headset Disconnect/Reconnect cable 3. HAA20 Amplifier Box 4. AA batteries, 2 pcs FRONT PANEL 1. Speaker Volume Control 2. Microphone Volume Control 3. Mute Switch 4. Electret/Carbon Telephone Type switch 5. Telephone Headset/Handset Switch 6

10、. LED indicator 7. Battery Compartment 8. AC/DC Adapter (optional) Jack BACK PANEL 9. Headset Jack 10. Telephone Handset Jack 11. Telephone Jack 12. Ampbox Buzzer location 13. Scan Switch 12. 11. 10.9. 13. NOTICE: Every effort was made to ensure that the information in this guide was complete and ac

11、curate at the time of printing. However, information is subject to change. IMPORTANT SAFETY INFORMATION Always follow these basic safety precautions when installing and using the unit: 1. Read all instructions. 2. Follow all warnings and instructions marked on the product. 3. Never spill liquid on t

12、he product. 4. Repair or service must be performed by a factory authorized repair facility. 5. DO NOT staple or otherwise attach the AC power cord to building surfaces. 6. DO NOT use the product near water or in a wet or damp place. 7. DO NOT use extension cords. Install product within 6 feet of an

13、outlet. 8. DO NOT install telephone wiring during a lightning storm. FEATURES Supports both electret and carbon type telephone systems. Easy to install and user friendly. To conserve the battery, the unit automatically performs a power down (sleep mode) when the unit is not being used. It will autom

14、atically resume normal operation when an incoming signal is detected. The HAA20 will automatically learn your telephone handset configuration. Low battery and function LED indicator. - LED off: Standby or power down mode - LED on: Mute switch is on - LED flash: Battery low - During normal use, the L

15、ED will flicker with the incoming ring signal Power: two 1.5V AA battery or AC/DC adapter (optional). This unit will not alter the normal function of your telephone system. This unit will provide a hands-free solution during telephone usage. 2. 1. 3. 23 1. 6. 4. 5. 3. 8. 7. 2. Bogen 130% 9/26 10/5/0

16、1 11:08 AM Page 3 RadioFans.CN 收音机爱 好者资料库 CONTENTS 1. Telephone cable 2. Rapid Headset Disconnect/Reconnect cable 3. HAA20 Amplifier Box 4. AA batteries, 2 pcs FRONT PANEL 1. Speaker Volume Control 2. Microphone Volume Control 3. Mute Switch 4. Electret/Carbon Telephone Type switch 5. Telephone Head

17、set/Handset Switch 6. LED indicator 7. Battery Compartment 8. AC/DC Adapter (optional) Jack BACK PANEL 9. Headset Jack 10. Telephone Handset Jack 11. Telephone Jack 12. Ampbox Buzzer location 13. Scan Switch 12. 11. 10.9. 13. NOTICE: Every effort was made to ensure that the information in this guide

18、 was complete and accurate at the time of printing. However, information is subject to change. IMPORTANT SAFETY INFORMATION Always follow these basic safety precautions when installing and using the unit: 1. Read all instructions. 2. Follow all warnings and instructions marked on the product. 3. Nev

19、er spill liquid on the product. 4. Repair or service must be performed by a factory authorized repair facility. 5. DO NOT staple or otherwise attach the AC power cord to building surfaces. 6. DO NOT use the product near water or in a wet or damp place. 7. DO NOT use extension cords. Install product

20、within 6 feet of an outlet. 8. DO NOT install telephone wiring during a lightning storm. FEATURES Supports both electret and carbon type telephone systems. Easy to install and user friendly. To conserve the battery, the unit automatically performs a power down (sleep mode) when the unit is not being

21、 used. It will automatically resume normal operation when an incoming signal is detected. The HAA20 will automatically learn your telephone handset configuration. Low battery and function LED indicator. - LED off: Standby or power down mode - LED on: Mute switch is on - LED flash: Battery low - Duri

22、ng normal use, the LED will flicker with the incoming ring signal Power: two 1.5V AA battery or AC/DC adapter (optional). This unit will not alter the normal function of your telephone system. This unit will provide a hands-free solution during telephone usage. 2. 1. 3. 23 1. 6. 4. 5. 3. 8. 7. 2. Bo

23、gen 130% 9/26 10/5/01 11:08 AM Page 3 RadioFans.CN 收音机爱 好者资料库 INSTALLATION Note: The HAA20 is not compatible with a telephone that has the keypad located in handset. 1. Disconnect the telephone handset cable from the telephone and plug it into the handset jack (#10) indicated by the handset symbol.

24、2. Connect one end of the supplied telephone cable to the telephone jack (#11) indicated by the telephone symbol. Connect the other end to the handset jack on your telephone. 3. Connect the Rapid Headset Disconnect/Reconnect cable (supplied with the headset) to the headset jack (#9) indicated by the

25、 headset symbol. Connect the Rapid Headset Disconnect/Reconnect end of the cable to the actual headset. 4. Install the batteries or optional AC/DC adapter. Route cables to the rear of the HAA20 under the cable retention tangs. TELEPHONE HANDSET PROGRAMMING Please perform the following procedure to c

26、onfigure the HAA20 for your particular telephone. 1. Set the Telephone Type switch (#4) on the front panel to the C position and determine if the system performance is acceptable by making a call to another party. Note: If the LED is illuminated, switch the Mute Switch to the Mouth symbol for conver

27、sation. If performance is acceptable, skip the remaining steps in this section. If performance is not acceptable, follow these steps for the HAA20 to optimize its setup for your particular telephone. 2. Set the Telephone Type switch (#4) on the front panel to the “E” position. 3. Set the Mute switch

28、 (#3) to the mouth position. 4. Set the Telephone Handset/Headset switch (#5) on the front panel to the headset position. 5. Turn the HAA20 over and place the microphone portion of the telephone handset over the area labeled Buzzer (#12). 6. Push the Scan switch (#13) for no more than 1 second. Note

29、: You should hear tones from the HAA20. 7. When the tones stop, setup procedure is completed. Note: If the tones continue for more than 30 seconds, stop the process by pressing the Scan switch again. Then try the procedure again from step 5. If the tones continue for more than 30 seconds again, cont

30、act Bogen for technical assistance. 8. Place the handset back on the cradle of your telephone. MANUAL MODE The HAA20 also allows users to manually step through the different configu- ration settings. Following the steps below, the user can select the optimum configuration. Typically this would only

31、be done if either the Auto Learn was unable to select the optimum configuration setting or if many HAA20 ampli- fiers were to be set to the same configuration as in a call center application. 1. Set the Telephone Handset/Headset switch (#5) on the front panel to the Handset position. 2. Remove the t

32、elephone handset from its cradle and dial the number of a person to assist you in configuring the HAA20 by listening to the quality of your voice as you go through the seven different settings. Note: Each of the seven configuration settings is accessed using the scan switch and is identified by its

33、own unique tone. The tones sound like Do, Re, Mi, Fa, So, La, Ti. 3. Once the call is established, put on the headset and set the Telephone Handset/Headset switch (#5) to the Headset position. 4. Press and hold the Scan switch (#13) for approximately 3 seconds until the first tone is heard. You will

34、 have 12 seconds to test the units perform- ance using this setting. If the performance is acceptable, then wait for 2 short beeps from the HAA20 and the configuration will be stored. 45 Bogen 130% 9/26 10/5/01 11:08 AM Page 5 INSTALLATION Note: The HAA20 is not compatible with a telephone that has

35、the keypad located in handset. 1. Disconnect the telephone handset cable from the telephone and plug it into the handset jack (#10) indicated by the handset symbol. 2. Connect one end of the supplied telephone cable to the telephone jack (#11) indicated by the telephone symbol. Connect the other end

36、 to the handset jack on your telephone. 3. Connect the Rapid Headset Disconnect/Reconnect cable (supplied with the headset) to the headset jack (#9) indicated by the headset symbol. Connect the Rapid Headset Disconnect/Reconnect end of the cable to the actual headset. 4. Install the batteries or opt

37、ional AC/DC adapter. Route cables to the rear of the HAA20 under the cable retention tangs. TELEPHONE HANDSET PROGRAMMING Please perform the following procedure to configure the HAA20 for your particular telephone. 1. Set the Telephone Type switch (#4) on the front panel to the C position and determ

38、ine if the system performance is acceptable by making a call to another party. Note: If the LED is illuminated, switch the Mute Switch to the Mouth symbol for conversation. If performance is acceptable, skip the remaining steps in this section. If performance is not acceptable, follow these steps fo

39、r the HAA20 to optimize its setup for your particular telephone. 2. Set the Telephone Type switch (#4) on the front panel to the “E” position. 3. Set the Mute switch (#3) to the mouth position. 4. Set the Telephone Handset/Headset switch (#5) on the front panel to the headset position. 5. Turn the H

40、AA20 over and place the microphone portion of the telephone handset over the area labeled Buzzer (#12). 6. Push the Scan switch (#13) for no more than 1 second. Note: You should hear tones from the HAA20. 7. When the tones stop, setup procedure is completed. Note: If the tones continue for more than

41、 30 seconds, stop the process by pressing the Scan switch again. Then try the procedure again from step 5. If the tones continue for more than 30 seconds again, contact Bogen for technical assistance. 8. Place the handset back on the cradle of your telephone. MANUAL MODE The HAA20 also allows users

42、to manually step through the different configu- ration settings. Following the steps below, the user can select the optimum configuration. Typically this would only be done if either the Auto Learn was unable to select the optimum configuration setting or if many HAA20 ampli- fiers were to be set to

43、 the same configuration as in a call center application. 1. Set the Telephone Handset/Headset switch (#5) on the front panel to the Handset position. 2. Remove the telephone handset from its cradle and dial the number of a person to assist you in configuring the HAA20 by listening to the quality of

44、your voice as you go through the seven different settings. Note: Each of the seven configuration settings is accessed using the scan switch and is identified by its own unique tone. The tones sound like Do, Re, Mi, Fa, So, La, Ti. 3. Once the call is established, put on the headset and set the Telep

45、hone Handset/Headset switch (#5) to the Headset position. 4. Press and hold the Scan switch (#13) for approximately 3 seconds until the first tone is heard. You will have 12 seconds to test the units perform- ance using this setting. If the performance is acceptable, then wait for 2 short beeps from

46、 the HAA20 and the configuration will be stored. 45 Bogen 130% 9/26 10/5/01 11:08 AM Page 5 If the performance is not acceptable, push the scan switch again within 12 seconds for the next setting and test again. Repeat this process until you find the setting that gives the HAA20 acceptable performan

47、ce. The unit will continuously rotate through the available settings as the Scan switch is pressed. 5. After the optimum setting is stored, terminate the call by putting the tele- phone handset back on its cradle. The configuration process will be completed. OPERATION It is recommended that you call

48、 someone to help you make initial volume adjustments and enable you to get familiar with using the HAA20 before using it for business service. Perform the following steps to operate the HAA20. 1. Ensure that the Mute switch (#3) is in the mouth position and the Telephone Handset/Headset switch (#5)

49、is in the headset position. 2. Remove the handset of your telephone from its cradle. 3. Wait until you hear a dial tone and dial the number of the party you wish to contact. 4. Adjust the receive volume of the Headset for a comfortable listening level. 5. If the person on the other end of the line has trouble hearing you, adjust the MIC volume control. 6. Place the Handset of your telephone back on its cradle to terminate a call. Note: The handset of your phone still controls the state of your phone (hung up or off hook). You may at anytime during a call switch between the handset