Bogen-HS15EZ-Operation-Manual 电路图 维修手册.pdf

《Bogen-HS15EZ-Operation-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Bogen-HS15EZ-Operation-Manual 电路图 维修手册.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。

1、Easy Design TM Speaker Model HS15EZ, HS15EZW Speaker Layout The layout of the speakers should be planned prior to installation. Desired mounting height, barring obstructions, is 15 to 20 feet, with the speakers angled downward toward the listening area and facing in the same direction. Layout starts

2、 in one corner of the area. The first speaker in Row 1 should be positioned a dis- tance equivalent to (A) (s ee Figure 2) from the corner based on the noise level of the area. The next speaker in Row 1 should be a distance equivalent to (B) (s ee Figure 2) from the first speaker. Each additional sp

3、eaker in the row should use this same spacing. Row 2 starts a distance equivalent to (C) (s ee Figure 2) from Row 1 and, like Row 1, each speaker should be a distance apart equivalent to (B). Row 3 starts a distance equivalent to (C) from Row 2. Continue this pattern of alternating rows until the ar

4、ea is appropriately covered. For areas that include high shelving or corri- dors, speakers should be installed so that they project down the aisles between the shelves or down through the corridors. The spacing of the speakers can be adjusted so that the speakers are evenly spaced in a row. NOTE: Ea

5、ch env ir onment is uniq ue. This layout p lan is gener al in nat ur e and may not be ap p licable for ev er y ins t allat ion. Figure 1 STARTHORN SPEAKER A B C Row 1 Row 2 Row 3 Row 4 50 ft.100 ft.60 ft.1/2 Rotation Figure 2 Specifications subject to change without notice. 1999 Bogen Communications

6、 Inc. All rights reserved. Part No. 54-5072-01C 0809 High Noise (75dB-85dB) Very High Noise (85dB-95dB 30 ft.65 ft.40 ft.Full Clockwise ABCVolume Setting PLACEMENT 50 Spring Street, Ramsey NJ 07446 Tel. 201-934-8500 Fax: 201-934-9832 RadioFans.CN 收音机爱 好者资料库 Speaker Installation STEP 1 - For easier i

7、nstallation, remove the flange (bas e) from the speaker by unscrewing the wing nut while at the same time pressing inwardly on the wing nut. Place the flange flush with the mounting surface and mark the location of the three holes with either a marker or chisel. It is important that the three holes

8、be exactly aligned with the flange, otherwise you might stress the base or make the connection unsteady. Drill the necessary holes and screw the flange to the surface (s ee Figure 3). (Us e appr o- pr iat e har dwar e for your s pecific mount ing s ur face.) NOTE: The s peaker may als o be s t r ap-

9、mount ed us ing s t andar d 1/2-inch indus t r ial s t r apping. STEP 2 - After mounting the flange, reattach the speaker to the flange and aim the speaker for the desired coverage. A 45-degree downward angle is recommended, but this may vary depending upon speaker layout. STEP 3 - Remove the plasti

10、c cover to make the electrical con- nection and set the volume control (s ee Figure 4). The suggested amplifier connections are: Amplifier Outputs Speaker Connections 70V Terminal 1 COMTerminal 2 NOTE: The s p eaker will als o wor k p er fect ly well wit h t hes e connect ions r ev er s ed. Howev er

11、 , it is impor t ant t o be cons is t ent in t he wir ing of t he s peaker s in t he s ys t em. STEP 4 - Adjust the volume control to the desired setting. See Figure 2 for the suggested initial settings based on the ambient noise level of the environment. Place the plastic protective cover back over the exposed area. NOTE: The t wo fur t her mos t clockwis e s et t ings (pos it ions 7 Exclusion of Certain Damages RadioFans.CN 收音机爱 好者资料库