Bogen-UTI312-Operation-Manual 电路图 维修手册.pdf

《Bogen-UTI312-Operation-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Bogen-UTI312-Operation-Manual 电路图 维修手册.pdf（32页珍藏版）》请在收音机爱好者资料库上搜索。

1、Zone Cont roller wit h Univ ers al Telephone Int erfac e UTI312 Model Installation and Use Manual 2005 Bogen Communications, Inc. All rights reserved. Specifications subject to change without notice. 54-2120-01D 1203 RadioFans.CN 收音机爱 好者资料库 Notice Every effort was made to ensure that the information

2、 in this manual was complete and accurate at the time of printing. However, information is subject to change. FCC Statement (Part 15) - Radio Frequency Interference The Universal Telephone Interface generates and uses radio frequency energy and if not installed and used in strict accordance with the

3、 manufacturers instructions, may cause interference to radio and television reception. Testing is being conducted for compliance with the limits for a Class B device in accordance with the specifications in Part 15 of the FCC Rules and Canadian D.O.C. regulations. This testing is designed to provide

4、 reasonable protection against such interference. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the UTI312 unit off and on, the user is encou

5、raged to try to correct the interference by one or more of the following measures: - Reorient the radio or TV receiving antenna. - Relocate the UTI312 unit with respect to the radio or TV receiver or vice-versa. - Plug the UTI312 unit into a different outlet so that it and the radio or TV receiver a

6、re on different branch circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, How To Identify and Resolve Radio-TV Interference Problems, helpful. This booklet was prepared by the F

7、ederal Communications Commission (FCC) and is available from the U.S. Government Printing Office, Washington, DC 20402. Stock order No. 004-000-00345-4. Federal Communications Commission (FCC) Statement (Part 68) This equipment is component registered with the Federal Communications Commission (FCC)

8、 in accordance with Part 68 of its rules. In compliance with the rules, be advised of the following: Registered equipment may not be used with Coin Telephone Lines. Equipment may be used with Party Lines in areas where state tariffs permit such connections and when equipment is adaptable for such se

9、rvice. This equipment is registered as follows: Registration Number - CD2PA13BUTI312 Ringer Equivalence - 1.4B If trouble is experienced, the equipment should be disconnected from the interface to determine if this equipment, or the telephone line is the trouble source. If the equipment is determine

10、d to be malfunctioning, it should not be reconnected until repairs are effected. Repairs to this equipment, other than routine repairs, can be made only by the manufacturer or its authorized agents. If the equipment causes harm to the telephone network, the local telephone company may temporarily di

11、scontinue your service and, if possible, notify you in advance. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC. The local telephone company may make cha

12、nges in its facilities, operations, or procedures that could affect the proper functioning of your equipment. If they do, you will be given adequate notice in writing to allow you an opportunity to maintain uninterrupted telephone service. Important Safety Information Always follow these basic safet

13、y precautions when installing and using the system: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. DO NOT block or cover the ventilation slots and openings. They prevent the product from overheating. DO NOT place the product in a separate e

14、nclosure or cabinet, unless proper ventilation is provided. 4. Never spill liquid on the product or drop objects into the ventilation slots and openings. Doing so may result in serious damage to the components. 5. Repair or service must be performed by a factory authorized repair facility. 6. The pr

15、oduct is provided with a UL-CSA approved, 3-wire ground type plug. This is a safety feature. DO NOT defeat the safety purpose of the grounding type plug. DO NOT staple or otherwise attach the AC power supply cord to building surfaces. 7. DO NOT use the product near water or in a wet or damp place (s

16、uch as a wet basement). 8. DO NOT use extension cords. The product must be installed within 6 feet of a grounded outlet receptacle. 9. DO NOT install telephone wiring during a lightning storm. 10.DO NOT install telephone jacks in a wet location unless the jack is specifically designed for wet locati

17、ons. 11.Never touch uninsulated wires or terminals, unless the line has been disconnected at the paging or controller interface. 12.Use caution when installing or modifying paging or control lines. RadioFans.CN 收音机爱 好者资料库 Contents 3 Introduction .4 Voice Channel .4 Background Music.4 Signaling Tones

18、 .4 Other Features .4 Package Contents .4 Panel Descriptions.5 Installation .6-7 Mounting .6 ZX3 Module Installation also compatible with 70V amp inputs Zone activity LEDs Zone contact closure Pre-Announce/Confirmation Tone Adjustable Automatic Level Control with threshold and active indicator Backg

19、round Music Two high-impedance transformer isolated BGM inputs Individual volume controls Background music source selectable per zone Stereo combining inputs Signaling Tones Night Ringer (90V and contact closure activation) with zone group Two Tone Triggers (tone and duration selectable, closure act

20、ivated) with individual zone groups Code Calling with zone group Other Features Flexible dialing plan for zone numbers 2 to 5 digit dialing plans 24 zone groups C-form contact set with programmable activation events Non-volatile memory for setup data Setup Tone to assist in volume setting, etc. Plug

21、gable terminal strips Microcontroller-based operation DTMF setting of operating parameters Package Contents (1) UTI312 (1) Installation and Use Manual (1) ZX3 Module (installed) (2) Brackets 5 Panel Descriptions UTI312 Callouts 1.Ground Start Terminal - Connection for PBX ground. Used only when the

22、ground start interface is selected. 2.Earth Ground Terminal - Provides connection to the UTI312 Earth Ground. This terminal can be connected to the GND STRT terminal when using the ground start interface if the UTI312 and the PBX share the same Earth Ground. 3.AUX Contact Terminals - Provides connec

23、tions for normally open and normally closed contact closures. The contact closure can be programmed to activate during paging, night ring, tone, override, or any combination (refer to System Programming). 4.Tone and Night Ring Terminals / Tone and Night Ring Level Controls - Terminals provide connec

24、tions to night ring and tone trigger inputs. Tone Level control sets the level of all tones produced by the system except for the Night Ring tone. Night Ring Level control sets level of Night Ring tone. 5.Program/Run Switch add up to 3 additional ZX3 modules for up to 12 paging zones. 20. Module Bay

25、 - Module bay accepts up to four ZX3 modules, for a total of 12 zones of paging. One pre-installed. 21. Auxiliary 24V Terminals - Provides connections to the UTI312 1A, 24V DC power supply for powering self-amplified speakers. LEVEL 100 24 VDC POWER +- ZONES LEVEL 100 LEVEL 100 T R N.O. C N.C. T R N

26、.O. C N.C. T R N.O. C N.C. ZX3 Installation Mounting Wall Mounting Mounting to a plywood backboard or studs: 1. On each side remove the four screws in the corners and use them to attach the mounting flanges so that the flanges are facing the rear of the unit. 2.Hold the unit level against the surfac

27、e to which it will be mounted. 3.Using the keyholes, mark on the mounting surface where the mounting screws (not included) should be positioned. 4. Set the unit aside and install the screws leaving about 1/4 of the screws sticking out of the surface. 5. Slip the unit over the screws through the keyh

28、oles and let the unit rest on the screws. Tighten screws snugly. Rack Mounting, Flush Mounting flush to a rack: 1. On each side remove the four screws in the corners and use them to attach the mounting flanges so that the flanges are facing the front of the unit. 2.Attach unit to rack with 4 rack sc

29、rews (not supplied). Do not use keyholes for mounting to a rack. Rack Mounting, Recessed for Wire Access Recessed in a rack to allow for top or bottom wire entry: 1. On each side remove the four screws in the corners and use them to mount the mounting flanges so that the flanges are protruded from t

30、he front of the unit. This recess allows enough space for wire access from top or bottom. 2.Attach unit to rack with 4 rack screws (not supplied). Do not use keyholes for mounting to a rack. Rack Mounting Considerations If installed in a closed or multi-unit rack assembly, the operating ambient temp

31、erature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturers maximum rated ambient temperature (Tmra). Maximum recommended ambient temperature for the UTI312 is 40 C and 104

32、F. Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised. Circuit overloading consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuit

33、s might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than dire

34、ct connections to the branch circuit (e.g., use of power strips). 6 Wall Mounting Rack Mounting, Wire Access Rack Mounting, Flush ZX3 Module Installation 12 = 120 seconds.) Ex.: 05003# for 30 seconds. If you wish to inhibit the default timer, enter 00 for the time data. VOX Timer To set the time dur

35、ation for the VOX time-out, enter the feature code 051 followed by a single digit from 1 to 9, corresponding to 1 to 9 seconds, followed by the # key. Ex.: 0515# for 5 seconds. To inhibit the timer, enter the Feature Code followed by 0. Note: If both the default and VOX timers are inhibited, the onl

36、y way to release the UTI312 from a station line is through the use of a Calling Party Control (CPC) pulse of 300 ms or longer. 20 AUX Relay Contact The UTI312 allows the installer to program a number of different parameters to control the way in which the UTI312 AUX relay contact activates. The UTI3

37、12 allows programming of which input events (Override, Tone Trigger 1 and 2, Page, and Night Ring) it will respond to, whether it will respond to the event only (Event-Driven Mode) or to a combination of the event and its place in the priority structure (Priority-Driven Mode), and if the contact wil

38、l respond during the event (No Delay) or after the event ends (Delay). Event Enable/Disable The UTI312 monitors for 5 types of input events: Override, Tone Trigger 1, Tone Trigger 2, Page and Night Ring. When one of these inputs is activated, the UTI312 detects that as a particular event. Through pr

39、ogramming, the installer can decide which of these 5 events the UTI312 will allow to activate the AUX relay. Setting the event to Enable allows the AUX contact to respond to that event. For example, if the application requires that the AUX relay contacts respond only when the Night Ring input is act

40、ive, the installer would enable the Night Ring event and disable all other events (Override, Tone Trigger 1 FCC Part 68; Industry Canada CS-03; FCC Part 15 Dimensions:16-3/8 W x 3-1/2 H x 4-7/8 D 19 W x 3-1/2 H x 4-7/8 D (with mounting flanges) 28 Product Weight:8 lb. * Ground points marked with an

41、asterisk must not be connected to Earth Ground when GND ST terminal is connected to Earth Ground. Block Diagram, UTI312 29 * Ground points marked with an asterisk must not be connected to Earth Ground when GND ST terminal is connected to Earth Ground. Block Diagram, ZX3 30 The Bogen UTI312 Zone Cont

42、roller is warranted to be free from defects in material and workmanship for two (2) years from the date of sale to the original purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes defective (as confirmed by Bogen upon inspection) during the app

43、licable warranty period, will be repaired or replaced by Bogen, at Bogens option, provided the product is shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. Repaired or replacement product will be returned to you freight prepaid. This warranty

44、does not extend to any of our products that have been subjected to abuse, misuse, improper storage, neglect, accident, improper installation or have been modified or repaired or altered in any manner whatsoever, or where the serial number or date code has been removed or defaced. THE FOREGOING LIMIT

45、ED WARRANTY IS BOGEN S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER S SOLE AND EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMU

46、M EXTENT ALLOWABLE BY LAW. Bogens liability arising out of the manufacture, sale or supplying of products or their use or disposition, whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL, INCIDENTAL OR

47、CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not allow the exclusion or limitation

48、 of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State. Products that are out of warranty will also be repaired by the Bogen Factory Service Department same address as above or call 201-934-850