《Bogen-PRO6-Operation-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Bogen-PRO6-Operation-Manual 电路图 维修手册.pdf（18页珍藏版）》请在收音机爱好者资料库上搜索。
1、Just what you want to hear ProHoldTMDRDXTM Digital Download System Remote Unit Installation Guide RadioFans.CN 收音机爱 好者资料库 FCC Notice This equipment has been tested and found to comply within the limits for a Class A digital device, pursuant to Part15 of FCC rules. These limits are designed to provid
2、e reasonable protection against harmful interference in a res- idential installation. This equipment generates, uses and can radiate radio fre- quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guaran
3、tee that interference shall not occur in a particular installa- tion. If this equipment does cause harmful interference to radio (and) or televi- sion reception, which can be determined by turning the equipment on and off, and noting any change in said interference, the user is encouraged to try to
4、cor- rect the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or
5、 an experienced radio/TV technician for assistance. This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations Cet appareil numrique de la classe A respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. FCC Requirements 1.
6、 The Federal Communications Commission (FCC) has established Rules which permit this device to be directly connected to the telephone network. Standardized jacks are used for these connections. This equipment should not be used on party lines or coin lines. 2. If this device is malfunctioning, it ma
7、y also be causing harm to the telephone network; this device should be disconnected until the source of the problem can be determined and until repair has been made. If this is not done, the telephone company may temporarily disconnect service. 3. The telephone company may make changes in its techni
8、cal operations and procedures; if such changes affect the compatibility or use of this device, the telephone company is required to give adequate notice of the changes. 4. If the telephone company requests information on what equipment is con- nected to their lines, inform them of: (a) The telephone
9、 number that this unit is connected to, (b) the ringer equivalence number: 0.2B (c) The USOC jack required RJ11C, and (d) The FCC registration Number RadioFans.CN 收音机爱 好者资料库 Items (b) and (d) are indicated on the label. The ringer equivalence number (REN) is used to determine how many devices can be
10、 connected to your telephone line. In most areas, the sum of the RENs of all devices on any one line should not exceed five (5.0). If too many devices are attached, they may not ring properly. Service Requirements 5. In the event of equipment malfunction, all repairs should be performed by our Compa
11、ny. It is the responsibility of users requiring service to report the need for service to our Company or one of our authorized agents. Service can be facilitated through our office at: Bogen Communications, Inc., 50 Spring Street, Ramsey, NJ 07446 Phone: (201) 934-8500. Warning: Changes or modificat
12、ions to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 1997 Bogen Communications, Inc. 50 Spring St., Ramsey, NJ 07446 All rights are reserved. No part of this document may be photocopied, reproduced, or translated to
13、 another language without the prior written consent of Bogen Communications Inc. Notice: The information contained in this document is subject to change without notice and should not be construed as a commitment by Bogen Communication, Inc. Bogen Communications Inc. assumes no responsibility for any
14、 errors that may appear in this document nor does it make expressed or implied warranty of any kind with regard to this material, including, but not limited to, the implied war- ranties of merchantability and fitness for a particular purpose. Bogen Communications Inc. shall not be liable for inciden
15、tal or consequential damages in connection with, or arising out of the furnishing, performance, or use of this docu- ment and the equipment which is describes. Part No. 54-5033-01 June, 1997 Printed in Korea RadioFans.CN 收音机爱 好者资料库 Important Safety Instructions 1. Read and follow all instructions. 2
16、. Follow all warnings and instructions marked on the product 3. Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or lau
17、ndry tub, in a wet basement, or near a swimming pool. 5. Do not place this product on an unstable cart, stand or table. The product may fall causing serious damage to the product. 6. Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect it from overheating
18、, these openings must not be blocked or covered. The openings should never be blocked by placing the product on the bed, sofa or other similar surface. The prod- uct should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless p
19、roper ventilation is provided. 7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply, consult your dealer or local power com- pany. 8. The power supply included with this product has a 2-prong plug for co
20、nnection with a standard electrical outlet. 9. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it. 10. Do not overload wall outlets and extension cords as this can result in the risk of fire or electri- cal shock. 11. Ne
21、ver push objects of any kind into this product through cabinet slots as they may touch dan- gerous voltage points or short out points that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 12. To reduce the risk of electric shock, do not disassemble thi
22、s product, but return it to the factory service center when some service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect assembly can cause electric shock when the product is subsequently used. 13. Unplug this product from the wal
23、l and refer servicing to the factory service center personnel under the following conditions: a. When the power supply cord or plug is damaged or frayed. b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally b
24、y following the operating instructions. Adjust only those controls that are covered by the operating instructions because improper adjust- ment of other controls may result in damage. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in
25、performance. 14. Avoid using a telephone during an electrical storm. There may be a remote risk of electric shock from lightning. 15. Do not use the telephone to report a gas leak in the vicinity of the leak. ProHoldTMDRDXTM Digital Download System DRDX Unit Installation Guide 1 Specifications Power
26、 Requirements: 9V AC. Power supply included with the unit provides 9V AC 800 mA from 110V AC Source Coding Method:IMA Standard Sampling Rate:128 Kilobits/sec minimal Memory Capacity: PRO4 DRDX - 4 minutes PRO6 DRDX- 6 minutes PRO8 DRDX - 8 minutes PRO12 DRDX- 12 minutes Memory Backup:20 year non vol
27、atile FLASH Memory Ext. Speaker Output:1 watt into 8 via standard RCA Phono Jack LINE Output:600 transformer balanced via standard RCA Phono Jack AUX Input:Local Analog Pre-amp input via standard RCA Phono Jack External Controls:VOLUME Control (tool accessible only) SPEAKER on/off switch External In
28、dicators:POWER LED - (red) PLAY LED - (green) LOAD LED - (green) PSTN Connection:Standard RJ11 analog loopstart station interface Modem Line Speed:33.6 KBPS basic rate + MNP5/V.42 bis Compression/ECC Mounting:Wall or Desk Top Dimensions:7” x 10” x 3.5” Shipping Weight:1.6kg./4lb. 2 Contents 1.Introd
29、uction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2.Front Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 3. Top Panel Controls and Connections . . . . . . . . . . . . . . . . . . . . . . . .6 4. Installation . . . . .
30、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 4.1 Unpacking & Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 4.2 Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 4.3 Connecting Power Supply .
31、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 4.4 Connecting to the PSTN Network . . . . . . . . . . . . . . . . . . . . . . . . . .7 4.5 Connecting to your Telephone System . . . . . . . . . . . . . . . . . . . . . .8 4.6 Connection to an External Speaker (optional) . . . . . . . .
32、 . . . . . . . . .8 4.7 Connection to a Local Music Source (optional) . . . . . . . . . . . . . . . .8 5.Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 6. Typical Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 6
33、.1 Direct Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 6.2 Time Share . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 6.2.1 External Share Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 6.
34、2.2 Parallel Time Share . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 6.2.3 Distinctive Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 6.3 PBX/KSU Station Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 7. Troub
35、leshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 8. Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 3 1. Introduction The ProHold DRDX is the latest addition to the ProHold Series of Message On Hold Digital Announcers
36、 form BOGEN Communications. The ProHold Remote DRDX is designed to provide the end-user with superior DDD Digital Message Quality, combined with flexible programming. With ProHold DRDX there are no more lost tapes, worn out heads or gummy capstans. ProHold DRDX is virtually maintenance free. There a
37、re absolutely no moving parts to wear or break. In fact, once your ProHold DRDX is installed, you may never have to touch it again. Every feature is able to be controlled remotely. Each ProHold DRDX unit Features: Full Digital Audio Quality - Digital Door-to-Door (DDD) Fully Automatic On-Board Digit
38、al Mixing 20 year Non Volatile FLASH Audio Memory Backup Bogen STC (Single Track Control) - Precision Audio Editing Bogen B-mail Audio Delivery Software Instant Access Downloads - Anywhere, Anytime Line share with fax machine or other telco device Choice of 600 or 1 watt 8 output Choice of Digitally
39、 Recorded Music Bed or Local Analog Bed Built-in Monitor Speaker with on/off switch Status LED Indicators Choice of Local or Remote Volume Control Choice of Two Fully Independent Programs Time of Day Program Switching Unit Operation is as simple as FLASH-n-PLAY! Just connect ProHold DRDX to your PBX
40、/KSU MOH port, plug in the PSTN line and plug the power sup- ply into the wall. Now just call your Studio and within minutes youre up and running. No more waiting for the snail mail postman! 4 2. Front Panel Features 1.LED Indicators POWER, PLAY and LOAD. The POWER LED is lit when unit is plugged in
41、to wall. The PLAY LED is lit when unit is playing either Program. The LOAD LED is lit only when the unit is communicating with the Base Station. 2.Monitor Speaker Lets you monitor playback levels and locally set via the local volume control. A SPKR ON/OFF switch is included on the top panel. 5 1 2 3
42、. Top Panel Controls and Connections KeyIdentifierDescription 19V ACJack accepts 9V AC power to the unit. The power supply included with the unit provides 9V AC 800mA from a 110V AC source. 2.1 WATTRCA Phono Jack - 1 watt into 8 3LINE 600 600 output to the MOH input on a telephone system or to the a
43、mplifier of a loudspeaker system 4.AUX INLocal analog input provides analog music bed 5SPKR ON/OFF Speaker on/off switch - controls monitor speaker output 6VOLUMEControls the output level of the monitor speaker, LINE and 1 watt output jacks. 7TEL LINEStandard RJ11 Analog Station Jack - provides remo
44、te connection services 6 1234567 4. Installation 4.1 Unpacking & Inspection Your ProHold DRDX unit was carefully checked and inspected at the factory. Inspect the carton and unit for signs of damage as you unpack your unit. If damage is found, notify the dealer from whom the unit was purchased. If y
45、ou received the unit through the mail, you must file a claim with the carrier. 4.2 Installation Precautions Please observe the following Installation Precautions: Do Not install the unit in damp areas, or in areas where it is likely to be exposed to moisture. Do Not install the unit in areas where t
46、he ambient temperature is likely to go below 40F or exceed 90F. Make sure to use suitable fasteners when mounting the unit on hol- low walls or other similar thin materials. Plastic screw anchors are provided. 4.3 Connecting Power Supply Connect the output plug from the power supply included with th
47、e unit to the 9V AC jack on the rear panel of the ProHold DRDX. Plug the power supply into any convenient 110V AC outlet. 4.4 Connecting to the PSTN Network Connect the RJ11 jack, (phone line jack) located on the rear panel of the ProHold DRDX, to any convenient analog station line using the standar
48、d tele- phone line cable provided with the unit. Helpful HINT: Record the number of the phone line you are connecting to ProHold DRDX - you will need it later. 7 4.5 Connecting to your Telephone System Use the audio cable terminated with an RCA type plug (provided) to connect the LINE 600 output or
49、1 watt output to your telephone systems Message- on-Hold (MOH) input. (The outputs may also be used to feed into the input of a loudspeaker system amplifier.) 4.6 Connection to an External Speaker (optional) The 1 watt output RCA Phono Jack may be used to power an external 8 speaker. The output provides 1 watt into 8. 4.7 Connection to a Local Music Source (optional) If desired a Local Preamplified Analog Music source may be connected to the AUX IN RCA Phono Jack on the top panel of the ProHold DRDX unit. Local music input will be optionally mixed with th
免费区 
