Marantz-DV-6200-Service-Bulletin 电路图 维修手册.pdf

《Marantz-DV-6200-Service-Bulletin 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Marantz-DV-6200-Service-Bulletin 电路图 维修手册.pdf（3页珍藏版）》请在收音机爱好者资料库上搜索。

1、Approved by H. TamuraWritten by K. Ono Date:22-Nov-01Model:DV6200 Page:1/1REF.NBMZ01-027 SERVICE BULLETIN Subject: Circulation:Application: Improvement for selection the audio output while playback the VCD disc x for information customer complaint in case of service mandatory . MZxx0000 xxxxxx | MZx

2、x0146xxxxxx Int.ref: PHENOMENON When the VCD disc is played and then the AUDIO OUTPUT is selected by AUDIO button for the remote controller. It seems to be selected on screen and FLD. However the audio output is not changed. SOLUTION Update the firmware version from 1.0MP to 2.07MP. The way of firmw

3、are version up is as follows; Connect the DVD player to TV and operate by using Remote Controller 1) Insert the update disc (Part No. *DV6200CDR) into the product. 2) FLD indicates PrESS UP when the disc is detected. 3) Press ? ?(up) button. 4) FLD indicates rEAd 0 . If FLD indicated rEAd 1 or other

4、 number, please refer to the following . 5) FLD indicates UPgrAdE 0 . After few minutes, FLD indicate FInISHEd and the tray will be opened automatically. 6) Remove the disc. Press OPEN/CLOSE button and the power will be turned off automatically. 7) The product should be confirmed the firmware versio

5、n and be reset. 8) Press POWER button and press SETUP button. 9) Select “TV aspect” and press ? ?(right) button. 10) Press ?(up) button or ? ?(down) button and choose “16:9 wide”. Attention : Do not press SELECT/ENTER button ( Keep green triangle mark ) If check mark is appeared, press ? ?(right) bu

6、tton and change to green triangle mark. 11) Enter the code number 1397139 by Numeric buttons. 12) Press SELECT/ENTER button. The connected TV indicates “SYSTEM INFORMATION” Please check “MICOM-VER” is 2.07MP. If other number indicate, need to retry this procedure again. 13) Press POWER button and tu

7、rn off the power. Update firmware and Reset are succeeded. During reading the update disc, error messages are as follows Error Num = 1 3 You can retry to upgrade by disc. Because, flash ROM is not erased data yet. Error Num = 4 It is very worst case. The flash ROM is broken during erasing or program

8、ming. You need to rewrite from hardware (PC) for using another jig. REMARK This improvement has been done in the production line after the production week code number “0147” and later. The production week code is mentioned in the serial number label on the rear panel. (ex. MZxx0147xxxxxx) SYSTEM INF

9、ORMATION MODEL : DV6200/U1B REGION-NO :1 CHIP-ID :PANTERA II SERVO-VER :b003 MICOM-VER :V2.07 MP PROM OPTION :XX XX XX XX XX XX Factory Reset.Done Example indicated RadioFans.CN 收音机爱 好者资料库 Approved by H.TAMURA Written by K.ONO WQ-19 2 817/additional rule3 (1st Issue 2003-03-19) Date:15-May-2003Model

10、DV4200/DV6200 Page:1/1REF.NBR:MZ02-025 Circulation:Application: Subject: Int.ref: PHENOMENON 1) Sound skips and picture freeze 1 second at the chapter 8 with DVD disc “Beauty and Beast”. 2) Subtitle will be ON automatically at the chapter 3 with DVD disc “SPY GAME”. 3) Subtitle will be ON automatica

11、lly at the 1700” with DVD disc “The World is not Enough”. SOLUTION Update the firmware version to Ver.2.21MP. The way of firmware version up is as follows; Connect the DVD player to TV and operate by using Remote Controller 1) Insert the update disc (Part No. *DV4200CD3) into the product. 2) FLD ind

12、icates PrESS UP when the disc is detected. 3) Press ?(up) button. 4) FLD indicates rEAd 0 . If FLD indicated rEAd 1 or other number, please refer to the following . 5) FLD indicates UPgrAdE 0 . After few minutes, FLD indicate FInISHEd and the tray will be opened automatically. 6) Remove the disc. Pr

13、ess OPEN/CLOSE button and the power will be turned off automatically. 7) The product should be confirmed the firmware version and be reset. 8) Press POWER button and press SETUP button. 9) Select “TV aspect” and press ?(right) button. 10) Press ?(up) button or ?(down) button and choose “16:9 wide”.

14、Attention : Do not press SELECT/ENTER button ( Keep green triangle mark ) If check mark is appeared, press ?(right) button and change to green triangle mark. 11) Enter the code number 1397139 by Numeric buttons. 12) Press SELECT/ENTER button. The connected TV indicates “SYSTEM INFORMATION” Please ch

15、eck “MICOM-VER” is 2.21MP. If other number indicate, need to retry this procedure again. 13) Press POWER button and turn off the power. Update firmware and Reset are succeeded. During reading the update disc, error messages are as follows Error Num = 1 3 You can retry to upgrade by disc. Because, fl

16、ash ROM is not erased data yet. Error Num = 4 It is very worst case. The flash ROM is broken during erasing or programming. You need to rewrite from hardware (PC) for using another jig. REMARK This improvement has been done in the production line after the production week code number “0250” and late

17、r. The production week code is mentioned in the serial number label on the rear panel. (ex. MZxx0250 xxxxxx) SERVICE BULLETIN Improvement for playability of DVD disc “Beauty and Beast” and subtitle problem with some disc x for information customer complaint in case of service mandatory . Before MZxx

18、0249xxxxxx SYSTEM INFORMATION MODEL : DVxxxx/xxx REGION-NO :1 CHIP-ID :PANTERA II SERVO-VER :b003 MICOM-VER :V2.21 MP PROM OPTION :XX XX XX XX XX XX Factory Reset.Done Example indicated RadioFans.CN 收音机爱 好者资料库 Approved by S.NAGAO Written by WQ-19 2 817/additional rule 3 (1st Issue 2003-03-19) Date:1

19、5-May.-2003Model:DV4200,DV6200,VC5200 Page:1 / 1REF.NBR:MZ02-037 Circulation:Application: Subject: Int.ref: PHENOMENON 1. Can not playback by the some encoding software of the MP3 disc. 2. The black color of the video output is light. 3. Can not playback DVD disc ”WALT DISNEY ATLANTIS.(Only U.S.A. ”

20、/U1B” version occurs) SOLUTION Update firmware version to Ver.2.11MP and over Firmware Update Procedure DV4200 and DV6200-Refer to service manuals 2-8 pages “How to upgrade by upgrade DISC”. VC5200-Refer to SERVICE BULLETIN MZ01-023 (22-Nov-01) NECESSARY PART Update firm ware (Ver2.21MP) Disc Part n

21、o. *DV4200CD3 REMARKS The countermeasure apply to this claim only. This solution has already been applied in the production line after the week code number “MZ000206xxxxxx” and after. The week code number are printed in the serial number label on the rear panel. (ex.MZxx0206xxxxx) SERVICE BULLETIN Problem with playability of MP3 Disc and can not playback DVD disc ”WALT DISNEY ATLANTIS. x for information customer complaint in case of service mandatory . See Below RadioFans.CN 收音机爱 好者资料库