McIntosh-MA6300-Remote-Control-Addendum 电路图 维修手册.pdf

《McIntosh-MA6300-Remote-Control-Addendum 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《McIntosh-MA6300-Remote-Control-Addendum 电路图 维修手册.pdf（21页珍藏版）》请在收音机爱好者资料库上搜索。

1、HR070 Series Remote Control Programming Guide RadioFans.CN 收音机爱 好者资料库 2 Use only fresh batteries of the required size and recommended type. When the battery voltage is low, the Push-button will blink 5 times after another Push-button on the Remote Control is pressed. Do not mix old and new batteries

2、, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities. If the Remote Control will not be used for an extended period, remove the batteries. They can leak chemicals and destroy the Remote Control. When discarding the Remote Control, co

3、mply with local rules or regulations. Bat- teries should never be thrown away or incin- erated but disposed of in accordance with the local regulations concerning battery disposal. For additional information please visit the McIn- tosh Web Site at . Introduction The McIntosh HR070 Series Remote Cont

4、rols (HR070, HR071, HR072 and HR073) supplied with McIntosh Preamplifiers, Integrated Amplifiers, A/V Control Centers, and Source Components not only control a McIntosh Component System, but also have the ability of controlling non McIntosh Components in your system. Refer to figures 1 through 4 The

5、 HR70 Series Remote Controls have stored in permanent memory the necessary information to send the correct commands to the component to be controlled. By entering a five digit numeric code the commands for controlling the component is activated. In the event the Remote Control doesn t have the code

6、to control a particular component, the Remote Control has the ability to learn and store the IR Sig- nals sent out by the Remote Control originally sup- plied with the component. 1. Open the battery compartment cover (located on the back of the remote). 2. Place the AA batteries in the compartment a

7、nd match the + and - polarity symbols inside. 3. Replace the cover. Battery Information Installing Batteries Figure 1 RadioFans.CN 收音机爱 好者资料库 3 Copyright 2009 by McIntosh Laboratory, Inc. Table of Contents Introduction .2 Battery Information .5 Installing Batteries .6 Installation .7 Figure 2Figure

8、3Figure 4 RadioFans.CN 收音机爱 好者资料库 4 Program this Remote Control by first find the codes for the components you want to program (starting on page XX) and then follow the steps below: 1. Turn on the component (in this example, the TV). 2. Press TV Push-button on the Remote Control to be programmed. Re

9、fer to figure 5. 3. Press and hold SET Push-button until the Push- button illuminaton blinks twice, then release. 4. Enter the first five-digit code for the component (TV) and brand that you wish to program. The Push-button blinks once as each digit is entered. If the code is valid, the Push-button

10、blinks twice. Note: If the Push-button does not blink twice, repeat steps 2 to 4 and try entering the code again. 5. Aim the McIntosh Remote Control at the compo- nent and press Power Off. The TV should turn Off. If it does not, repeat steps 35, trying each code for your brand until you find one tha

11、t works. If you cannot find a working TV codes refer to “Searching Codes” on this page. Note: There might be more than one Program Code Number capable of switching power Off to the TV. Choose the Code Number with the great- est number of desired active commands for the TV to be controlled. 6. Repeat

12、 steps 1 to 5 for the other components you want to control. For future reference, write down each working component code below: HR Series Remote Control Programming Assigned Push-buttonComponentProgram Code TV CBL SAT AUX DVR Programming a Component If your component (TV in the Programming a Compo-

13、nent example) does not respond to the Remote Control Control after trying all codes listed for your (TV) brand, or if your TV brand is not listed, try searching for your code: 1. Switch On the TV you wish to control. 2. Press the TV Push-button on the Remote Control Control once. 3. Press and hold S

14、ET Push-button until the Push- button illuminaton blinks twice, then release. 4. Enter 9 9 1, then the component group number (see below). The Push-button blinks twice. Code NumberComponent Group 0Cable (Cable Converter, Video Accessories, Satellite Receivers) 1TV 2VCR (VCRs, DVD Players) 3Audio (Au

15、dio Amplifiers, Audio Amp /Tuners, CD Players) 5. Aim the Remote Control Control at the TV and press Power Off. The Remote Control sends IR Codes from its library to the selected TV, starting with the most popular code first. If the component responds, go to step 7. 6. If the component does not resp

16、ond, press LEVEL+ Push-button and the Remote Control will test the next code for that TV type. Continue to press LEVEL+ Push-button until the TV switches Off. Note: Press LEVEL- Push Button to try the previ- ous code. 7. Now that you have found the correct code, press SET to save the code that worke

17、d for the TV. The Push-button will blink twice to indicate the code has been saved. To search for other compo- nent codes, repeat steps 1 to 5. Searching for Code Used to activate Programming Mode Push-buttons available for Programming Push-buttons available for Programming Flashes during Programmin

18、g Figure 5 Push-buttons used to enter Program Code 5 Checking the Codes CHECKING THE CODES If you have set up the remote using the procedure in “Searching for Your Code”, you may need to find out which five-digit code is operating your quipment. For example, to find out which code is assigned to you

19、r TV: 1. Press TV once. 2. Press and hold SETUP until the red LED blinks twice, then release. 3. Enter 9 9 0. The LED blinks twice. 4. To view the code for the first digit, press 1. Count the LED blinks (for example, three blinks = 3), and write down the number in the appropriate code listing at the

20、 top of this column. NOTE: If a code digit is 0, the LED does not blink. 5. Repeat step 4 for the four remaining digits, using 2 for the second digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth digit. 6. To check for other device codes, repeat steps 15, substituting the devic

21、e key the desired mode you would like to check. USING LEARNING This universal remote control includes a Learning feature (some models may not include Learning) so you can add functions that are unique to your home entertainment components (e.g.,VCR Tracking Up or Down). However, there are some consi

22、derations. Learning Precautions Your original remote controls must be in working order for learning to work properly. Learned keys are mode-specific, so each one can store a unique function for each mode. Do not use the following keys for learning: Device Keys, SETUP, or Record (). Learning capacity

23、 is approximately 42 to 75 keys, depending on the code being learned. Certain device functions are not learnable including multi-frequency types, some high frequency ones, and other unusual formats. For optimum learning, avoid high levels of ambi- ent light such as natural sunlight or energy-efficie

24、nt fluorescent lights. NOTE: Please have your original remote controls handy before programming learning. Programming a Learned Key NOTE: If more than 10 seconds pass between key presses, the remote exits programming. 1. Place the Potenza head-to-head (about 2” apart) from your original remote contr

25、ol. Also locate the key (on your original remote control) that you want the Potenza to learn. Press the mode key you wish to learn keys on. 2. Press and hold SETUP until the LED blinks twice, then release. 3. Enter 9 7 5. The LED blinks twice. NOTE: If the LED displays one long flash instead, either

26、 your batteries are low, or the Potenza has a memory fault. In either case, the remote cannot learn a new key. 4. Press the key on the remote you wish to learn onto. The feedback LED will blink rapidly for three seconds, suggesting the remote is ready to learn. 5. On the original remote, press and h

27、old the key to be learned. Continue holding the key on the original remote until the Po- tenzas LED blinks twice. NOTE: If the LED displays one long blink, a learning error has occurred. Try repeating this step again until a successful capture oc- curs. If the function is still not captured, press a

28、nd hold SETUP to exit programming and review the “Learning Precautions” above. If needed, also see “Troubleshooting” below. After review, start programming again at step 1. 6. Repeat steps 4 through 5 for another key you would like to learn onto. Programming a Learned Push-button 6 Volume Lock Once

29、you have completed learning all keys, press and hold SETUP until the LED blinks twice to save all data learned. Deleting a Single Learning Key This process returns the key to its original program- ming for the mode you select. You can also delete learned programming by teaching a different function

30、to the key (see “Programming a Learned Key”). NOTE: If more than 10 seconds pass between key presses, the remote exits programming. 1. Press the mode key that you wish to remove the learned key from. 2. Press and hold SETUP until the LED blinks twice, then release. 3. Enter 9 7 6. The LED blinks twi

31、ce. 4. Press the key containing the learned function to be deleted twice. The LED blinks twice and exits from programming. Deleting All Learned Keys in a Specific Mode NOTE: If more than 10 seconds pass between key presses, the remote exits programming. 1. Press and hold SETUP until the LED blinks t

32、wice, then release. 2. Press 9 7 6. The LED blinks twice. 3. Press a mode key twice (i.e., TV. VCR/DVD, CBL/ SAT, etc.) to clear all the learned keys for that mode. The LED blinks twice and exits from programming. CHANGING VOLUME LOCK The Potenza universal remote control comes preset to allow indepe

33、ndent volume control of each selected device (Global Vol- ume Unlock). However, you may change the Volume Lock setting to Global Vol- ume Lock so that one devices volume will control volume in all other modes. After that, you can perform Individual Volume Unlock on a selected de- vice to set its vol

34、ume control for independent operation or Global Volume Unlock to remove all volume locking. Locking Volume Control to One Mode (Global Vol- ume Lock) 1. Press and hold SETUP until the red LED blinks twice, then release. 2. Enter 9 9 3, the LED blinks twice. 3. Press the mode key for the device you w

35、ant to con- trol (for example, TV). 4. The LED blinks twice. Now when you press VOL+, VOL-, or Mute, the selected device (for example, TV) controls the volume regardless of the current mode. Unlocking All Volume Control (Restoring Global Unlock) 1. Press and hold SETUP until the red LED blinks twice

36、, then release. 2. Enter 9 9 3, the LED blinks twice. 3. Press VOL+. The LED blinks four times. Volume is independently controlled for all programmed components. Unlocking a Single Devices Volume Control 1. Press a device key (TV. VCR/DVD, CBL/ SAT, etc.). 2. Press and hold SETUP until the red LED b

37、links twice, then release. 3. Enter 9 9 3. The LED blinks twice. 4. and then press VOL-. The LED blinks four times. Volume is independently controlled for the selected components. 11 Amplifier Adcom .30577, 31100 Bose . 30674 Carver .30892 Curtis Mathes .30300 Durabrand .31561 Elan .30647 GE .30078

38、Harman/Kardon .30892 JVC.30331 Left Coast .30892 Lenoxx .31561 Marantz .30892 McIntosh . 30251 Modulaire . 30395 NEC .30264 Optimus .30395, 30013, 30300, 30823 Parasound .30246 Philips .30892 Pioneer .30013, 30300, 30823 Polk Audio .30892 RadioShack . 30395 RCA .30013, 30300, 30823 Realistic.30395,

39、30013 Shure .30264 Sony .30689, 30815 Soundesign .30078 Victor .30331 Wards .30078, 30013 Yamaha .30354, 30133 Cable Set Top Box A-Mark .00008, 00144 ABC .00237, 00003, 00008, 00014, 00017 Accuphase .00003, 00014, 00017 Acorn .00237 Action .00237 Active .00237 Americast .00899 Amino .01822 Archer .00237 BCC .00276 Bell & Howell . 00014 Bell South .00899 British Telecom .00003 Century .00008 Citation . 00017 Clearmaster .00883 ClearMax.00883 Cool Box .00883 Coolmax .00883 Digeo .01187 Digi .