Philips-DVDR-9000-H-Service-Manual-2 电路图 维修手册.pdf

《Philips-DVDR-9000-H-Service-Manual-2 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-DVDR-9000-H-Service-Manual-2 电路图 维修手册.pdf（14页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by KC-TE 0547 AV Systems Printed in the Netherlands Subject to modifi cation EN 3139 785 31690 DVDR9000HHDD Video performance measured at Rear Cinch Audio Out: - S/N(Unweighted,5MHz-BW limitation, SC trap ON) : 52dB - Frequency response 0.1 to 4.8 MHz : +1/-5dB - Y/Chroma delay : 55ns 1.3.

2、2.3 DVB-T- Audio Performance DVB-T RF antenna signal IN ; Audio performance measured at Rear Cinch Audio Out: - S/N(A-weighted, 22kHz-BW limited) : 88dB - Frequency response 20Hz to 20kHz : 1dB - THD + Noise (at 1 kHz) : 85dB - THD + noise (ratio) for 16Hz to 20kHz : 65dB - Channel Separation (at 1k

3、Hz) : 100dB RadioFans.CN 收音机爱 好者资料库 EN 33139 785 316901. Technical Specifi cations and Connection Facilities 1.4 Analog Inputs / Outputs 1.4.1 SCART 1 (Connected to TV) Pin Signals: 1 Audio-out R 1.8V RMS 2 Audio-in R 3 Audio-out L 1.8V RMS 4 Audio GND 5 Blue / Chroma GND 6 Audio-in L 7 Blue-out 0.7

4、Vpp 0.1V into 75 8 Function switch 4.5V / 9.5V / 12V = asp. Ratio 4:3 DVD 9 Green GND 10 P50 control not use 11 Green out 0.7Vpp 0.1V into 75 12 NC 13 Red / Chroma GND 14 Fast switch GND 15 Red-out / 0.7Vpp 0.1V into 75 Chroma-out 300mVpp 3dB 16 Fast switch RGB / CVBS or Y out 1V / 10k Video - Cinch

5、 Input voltage : 1Vpp 3dB Input impedance : 75 Video - YC (Hosiden) According to IEC 933-5 Superimposed DC-level on pin 4 (load = 100k) 3.5V is detected as 16:9 aspect ratio Input voltage Y : 1Vpp 3dB Input impedance Y : 75 Input voltage C : 300mVpp 3dB Input impedance C : 75 1.4.4 Out 1 Component V

6、ideo Cinch Y/Pb/Pr according EIO-770-I-A, EIA-770-2 Audio - Cinch Output voltage : 2.2Vrms max. Output impedance : 10k 1.4.5 Out 2 Audio - Cinch Output voltage : 2Vrms max. Output impedance : 10k Video - Cinch Output voltage : 1Vpp 3dB Output impedance : 75 Video - YC (Hosiden) According to IEC 933-

7、5 Superimposed DC-level on pin 4 (load 100k) 3.5V is detected as 16:9 aspect ratio Output voltage Y : 1Vpp 3dB Input impedance : 75 Output voltage C : 300mVpp 3dB Input impedance : 75 1.5 Digital Inputs / Outputs 1.5.1 Digital Output Digital Audio Coaxial / Optical LCM : according IEC 60958 MPEG 1,

8、MPEG 2, AC3 : according IEC 61937 DTS : according IEC 61937 + addendum 1.5.2 HDMI Output Type A connector (19 pins) 1.5.3 Digital Video Input (IEEE 1394) Implementation Standard according: IEEE Std 1394-1995 IEC61883 - Part1 IEC61883 - Part 2 SD-DVCR (02-01-1997) Specifi cation of consumer use digit

9、al VCRs using 6.3mm magnetic tape dec.1994 Mechanical connection according to Annex of IEC 61883-1 RadioFans.CN 收音机爱 好者资料库 EN 43139 785 316901. Technical Specifi cations and Connection Facilities 1.10 Playability DVDR9000H Video Playback 1.Disc Media: CD-R/-RW, MP3- CD, VCD/SVCD, DVD-Video, DVD+R/+R

10、W, DVD-R/-RW x 2.Compression Format: MPEG1, MPEG2 x Audio Playback 1.Disc Media: CD, CD-R/-RW, MP3-CD x 2.Compression Format: Dolby Digital, MP3, MPEG2 Multi- channel, PCM x 3.MP3 bit rates: 32- 320 kbps x Still Picture Playback 1.Disc Media: Picture CD, DVD+R/+RW, CD-R/-RW x 2.Picture Compression F

11、ormat: JPEG x 1.5.4 G-Link (for IR-remote transmitting device) Output voltage : 5 0.5V (high level) 0.4 0.3V (low level) Output impedance : 150 1.6 Video Performance All outputs loaded with 75 SNR measurements over full bandwidth without weighting. 1.6.1 SCART (RGB) SNR : 55dB on all output Bandwidt

12、h : 4.8MHz -3dB 1.7 Audio Performance 1.7.1 Cinch Output Rear Output voltage 2 channel mode : 2Vrms 2dB Channel unbalance (1kHz) : 100dB Crosstalk 16Hz-20kHz : 87dB Frequency response 20Hz-20kHz : 0.5dB Signal to noise ratio (unweighted) : 85dB Dynamic range 1kHz : 83dB Distortion and noise 1kHz : 8

13、3dB Distortion and noise 16Hz-20kHz : 75dB Intermodulation distortion : 70dB Mute : 95dB 1.7.2 Scart Audio Output voltage 2 channel mode : 1.6Vrms 2dB Channel unbalance (1kHz) : 85dB Crosstalk 16Hz-20kHz : 70dB Frequency response 20Hz-20kHz : 0.5dB Signal to noise ratio (unweighted) : 80dB Dynamic r

14、ange 1kHz : 75dB Distortion and noise 1kHz : 75dB Distortion and noise 16Hz-20kHz : 50dB Intermodulation distortion : 70dB Mute : 80dB 1.8 Dimensions and Weight Height of feet : 5.5mm Apparatus tray closed : WxDxH:435x390 x89mm Apparatus tray open : WxDxH:435x525x89mm Weight without packaging : appr

15、ox. 7.1 0.5kg Weight with packaging : approx. 8.5kg 1.9 Laser Output Power & Wavelength 1.9.1 DVD Output power during reading : 0.8mW Output power during writing : 20mW Wavelength : 650nm 1.9.2 CD Output power : 0.3mW Wavelength : 780nm EN 53139 785 316902.Test Disc & Repair Hints 2.1 Test Disc 1) 7

16、104 099 96611 CD-RW printed Audio Disc 2) 9965 000 25728 DVD Player Test Pack 3) - Blank DVD+RW 4) - Blank DVD-RW 2.2 Open the DVD Tray manually Note: This procedure needs to be performed on condition that: - a customers Disc is jammed in the DVD Tray - the DVD Tray cannot be open via the normal ope

17、n/close button on the set. 1) Place the set on the table with the bottom faced upwards as shown below. 2) Insert a screw driver into the slot and open the DVD Tray by sliding the screw driver in the direction shown. Figure 2-1 2. Test Disc & Repair Hints 1 2 EN 63139 785 316903.Firmware Upgrading &

18、Diagnostic Software 3. Firmware Upgrading & Diagnostic Software 3.1 Firmware Upgrading A. Preparation to upgrade fi rmware: 1. Unzip the zip-archive fi le 2. Start the CD Burning software and create a new CD project (data disc) with the following settings: File system : Joliet Format : MODE 2: CDROM

19、 XA Recording mode : SINGLE SESSION (TRACK-AT-ONCE), FINALIZED CD Note: Long fi le name is necessary for the preparation of the upgrade disc 3. Place the content of the zip-archive into the root directory of the new CD project. 4. Burn the data onto a blank CDR or CD-RW B. Procedure to apply the fi

20、rmware upgrade: 1. Hold the + buttons down and Power up the set. 2. The tray opens and set will display: FORCE DL . PUT DSC 3. Insert the prepared Upgrade CDROM and close the tray. 4. The set will display: INIT DSC . DOWNLOAD . The whole process takes less than 15 minutes Note: Do not press any butt

21、ons or interrupt the mains supply during the upgrading process, otherwise the set may becomes defective. 5. When the upgrade is completed the tray will open automatically and the set will display: REMOVE 6. Close the tray and the set will display: DONE C. How to read out the fi rmware version to con

22、fi rm set has been upgraded: 1. Power up the set. 2. Press button on the Remote control and select Setup option 3. Press button to select System 4. The set will prompt you about clearing the Time Shift Buffer 5. Select Yes and press button 6. Press button several times to select Version info 7. Pres

23、s button 8. The TV connected to the set will display: DIF05_3/493AN SV11205 BE 43.2.13 ASP3,9,1,10FP DTTM HW:01020102 DTTM SW:00040200 SIT9000-FF3F-S3_F540 20051020-1815 pro sxcplusint EPG:3.04 DPMS:P_DPM 9. Press button to exit EN 73139 785 316904.Service Flow Chart 4. Service Flow Chart 4.1 Start

24、Process Start A (Verification Test) Is it a Hardware problem ? Upgrade to latest Firmware Is it a known complaint ? Is Firmware solution available ? Yes No Yes No Yes No Is the complaint solved ? Return set to Customer with Report on action done Yes No Is the complaint documented ? Yes No Service W/

25、S to contact the Trade / Customer to work out an action plan. Examples: - explain them that the Firmware solution is not ready - Upgrade disc will be send to them the moment a solution is ready - etc. Does the set pass the Dealer Test ? Pass Fail Perform built-in Dealer Test (Press & hold Play butto

26、n on Front Panel down + Power-up the set) Send refurbished set from pool stock to Trade / customer - Attached Defect Description Report and Proof of Purchase. - Pack defective set - Store defective set for pick-up EN 83139 785 316904.Service Flow Chart 4.2 Verifi cation Process * If complaint is rel

27、ated to System Menu setting Connect up the Recorder to TV antenna, TV set and an External source Check the Firmware version on the set Can the set Start-up ? Yes No A (Verification Test) B Recording Check C Playback Check D * System Menu Send refurbished set from pool stock to Trade / customer Retur

28、n set to Customer with Report on action done - Attached Defect Description Report and Proof of Purchase. - Pack defective set - Store defective set for pick-up No Yes Is Firmware the last released version ? Upgrade to latest Firmware Are the checks result ok ? Yes No EN 93139 785 316904.Service Flow

29、 Chart 4.3 Recording Process Manual Recording with TSBHDD:Manual Recording Copy to DVD Recordable discTimer Recording Does Timer recording functions ? Yes No Does manual recording functions ? Yes No B Recording Check Make a Timer recording with: - VPS/PDC on and off - Guide Plus+ System - Show View

30、System - manual recording Playback the recorded title from HDD browser Are Timer edit & delete feature working ? Yes No Make a manual recording to the HDD using different recording source: - Cam 1 (Front CVBS/S-Video) - Cam 2 (DV-in) - Tuner - Rear Ext 1/2 (external Cable Box/Satellite Receiver/VCR/

31、DVD) From the HDD browser select the recorded title and check the following: - edit title feature - play the title Does the TSB feature works ? 1) Switch the Recorder to Tuner source - The active Tuner channel will be recorded into the TSB (time shift buffer), a temporary HDD storage area. 2) By pre

32、ssing the INFO button the Time shift bar appears on the screen, check the following features: - search forward / backward - instant replay, pause, etc. on the live TV function 1) Make a short recording (1 minute) by selecting a portion in the TSB to be recorded. 2) Playback the recorded title from t

33、he HDD browser Does the recording functions ? Continue Continue Yes No Yes No Send refurbished set from pool stock to Trade / customer - Attached Defect Description Report and Proof of Purchase. - Pack defective set - Store defective set for pick-up 1) Insert a DVD+RW disc 2) In the HDD browser sele

34、ct the recorded title for copy to recordable DVD 3) From the Disc Menu select the copied title and check the following: - edit (Disc/Title) feature - play the title 4) Repeat with DVD-RW Does copy function ? Yes No Is the Disc Library feature working ? Yes No EN 103139 785 316904.Service Flow Chart

35、4.4 Playback Process HDD playback CheckDisc playback Check Yes No C Playback Check Playing other type of disc: 1) Use discs of DVD PLAYER TEST PACK for: - (Super) Video CD - MP3 disc - Picture disc (slide show) - special DVD playback check by layer change test using DVD disc of this package 2) For A

36、UDIO CD use of CD-RW printed Audio Disc to check: - Track 3 finger print - Track 8: 600u black dot (max. after 1 min.) From the DVD browser go through the Content, Title & Toolbar options Play a DVD video disc title and check the following: - Pause, Search Fwd/Rev & Next / Previous chapter - Edit fe

37、atures - T/C search Yes No Does the set work ? From the HDD browser check the following features: - Sorting - Delete, Copy & Protect - Edit features Does the set work ? ContinueContinue Yes No Send refurbished set from pool stock to Trade / customer - Attached Defect Description Report and Proof of

38、Purchase. - Pack defective set - Store defective set for pick-up Does the set work ? Play a title from the HDD browser and check the following features: - Pause, Search Fwd/Rev & Next / Previous chapter - Editing features - Yes NoDoes the set work ? EN 113139 785 31690 4.5 System Menu Process 4.Serv

39、ice Flow Chart D System Menu Check Does the set work ? Continue Yes No Toolbar - check the following features: - Option Setup - check the following features: - System - Time-date - Analogue Ch - Digital Ch - Video output - Audio output - Audio input - Language Preferences - check the following featu

40、res: - Recording - DV Specials - Sound - Disc - Access - Features Send refurbished set from pool stock to Trade / customer - Attached Defect Description Report and Proof of Purchase. - Pack defective set - Store defective set for pick-up EN 123139 785 31690 5. Directions For Use The following except of the Quick Use Guide serves as an introduction to the set. The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center: 5.Directions For Use EN 133139 785 316905.Directions For Use EN 143139 785 316905.