Philips-SACD-1000-Service-Manual-2.pdf

《Philips-SACD-1000-Service-Manual-2.pdf》由会员分享，可在线阅读，更多相关《Philips-SACD-1000-Service-Manual-2.pdf（163页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by MT 0101 Service PaCEPrinted in the NetherlandsSubject to modification? 3122 785 11020 Copyright 2001 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form

2、 or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. DVD-Video PlayerSACD 1000 /001 /171 /691 CL 06532152_000.eps 151200 ContentsPageContentsPage 1Technical specifications and connection facilities2 2Warnings, laser safety and service hints4 3

3、Directions for use7 4Mechanical- and dismantling instructions20 5Diagnostic software, trouble shooting and test instructions24 6Wiring and block diagrams Wiring diagram59 Block diagram (general)60 Block diagram (DAC PCB)61 7Electrical diagrams and print-layoutsDiagram PWB Display normal mode A weigh

4、ted: -114 dB (Typical) : 111dB SNR 1KHz, -160dB normal mode 500KHz: -50dB (Typical) : 40dB SNR 1KHz, -160dB custom mode 500KHz: 40dB (Typical) : 30dB THD 0dB 1KHz: 98dB (Typical custom mode) : 95 dB (Typical normal mode) THD 0dB 20Hz-20KHz: 96dB (custom mode) : 90 dB (normal mode) Dynamic range -60d

5、B: 114dB (Typical) : 108 dB Intermodulation distorsion CCIF: 108dB (Typical) : 102dB Low level linearity (-60 to -90 dB): 0.5dB Interchannel phase: 90dB PCM mode up to 6 channels (DVD/ CDDA): Output voltage (1 KHz): 2Vrms +/- 0.3V Channel unbalance: 108dB SNR dig. silence; normal mode A weighted: 11

6、1dB THD 0dB (1KHz): 95 dB typical THD 0dB (20Hz-20KHz): 90dB Dynamic range -60dB: 108dB Intermodulation distorsion CCIF: 105dB (Typical) : 100dB Low level linearity (-60 to -90 dB): 0.5 dB Interchannel phase: 90dB 1.3Video performance 1.3.1CVBS CVBS output loaded with 75 Ohm Fully according PQR3 IMS

7、 1.3.2S-video (Y/C) Fully according PQR3 IMS Connector pinning 1 - GND ? 2 - GND ? 3 - Y 1Vpp 0.1V into 75 Ohm 4 - C burst 300mVpp +1/-4dB into 75 Ohm Aspect ratio switching by DC on C(pin4). Connector type : 4 pin mini- DIN 1.4SCART Fully according PQR3 IMS Connector implementation according EN5004

8、9-1; color = black; dual SCART Fully according to prEN1057-2-1 Signal switching is P50 controlled; supported features of mode 3 see survey of applicable standards. 1.4.1SCART II (connected to TV) Pin signals: 1 - Audio R 1.8V RMS ? 2 - Audio R ? 3 - Audio L 1.8V RMS ? 4 - Audio GND ? 5 - Blue/Chroma

9、 GND ? 6 - Audio L ? 7 - Blue out/ Chroma in 0.7Vpp 0.1V into 75 Ohm (*) ? Technical specifications PAUSE - interrupts audio/video play or steps to the next picture frame REPEAT S PREV - selects previous track/title/chapter/index or beginning of current track/title/chapter/index T NEXT - selects nex

10、t track/title/chapter/index / OPEN/CLOSE - opens/closes the disc tray Disc loading tray 2 PLAY - starts audio/video play 9 STOP - stops audio/video play Directions for useGB 8SACD 10003. Remote control English 12 FUNCTIONAL OVERVIEW TV POWER SACD POWER SOUND MODE PLAYSTOP REVERSEPAUSESLOWFORWARD PRE

11、VIOUSRESUMENEXT ZOOM VOLCH DISPLAY ANGLE TITLE FTSSHUFFLESUBTITLEAUDIO DIMREPEATREPEATSCAN CHAPTER TC MUTE TV POWER - switches the TV to power/standby 9 STOP - stops playback SOUND MODE - selects required sound mode for SACD: CD, Stereo or Multi-channel (if available) for DVD/VCD: Stereo, Dolby Surr

12、ound, 3D sound or Multi- channel 2 PLAY - starts audio/video play 5 REVERSE - search backward ; PAUSE - pause or still frame/step frame H SLOW - slow motion 6 FORWARD - search forward J PREVIOUS - previous track/title/chapter/index e RESUME - resumes playback K NEXT - next track/title/chapter/index

13、VOL +/ - volume up/down in TV mode c MUTE - mutes the sound in TV mode CH +/ - program up/down in TV mode FTS - switches FTS function ON/OFF - displays FTS menu (FTS = Favourite Track Selection) SHUFFLE - playback in random order ZZ SUBTITLE - subtitle ON/OFF/selects subtitles (DVD/VCD/SVCD only) YY

14、 AUDIO - language selection SACD POWER BB - switches the player to power/standby MENU DISC - selects DVD-defined menu MENU SYSTEM - On-screen Display ON/OFF v w t u - up/down/left/right cursor movement in OSD mode RETURN - return to previous menu step aaZOOM - enlarges video image ANGLE - selects DV

15、D camera angle DISPLAY - selects elapsed Time display or Remaining Time display OK - acknowledge menu selection 0-9 - numerical key pad T - selects titles C - selects chapters PLAYER DISPLAY DIM - adjusts display brightness REPEAT - repeats a track or complete disc (CD, VCD, SACD) - repeats a chapte

16、r, title or complete disc (DVD) REPEAT A-B - repeats a particular passage (A-B) SCAN - playback of the first 10 seconds of each track, chapter, title Display English FUNCTIONAL OVERVIEW 11 Super Audio CD inserted Audio CD inserted Super Video CD inserted Video CD inserted indicate the current active

17、 sound mode DVD video disc inserted - number of titles on DVD in Stop mode - number of current title Number of current chapter - number of tracks on SACD/CD/VCD in Stop mode - number of current track track time in hours, minutes and seconds disc/program time in hours, minutes and seconds REM TIMErem

18、aining track time in hours, minutes and seconds when Display mode is set to Remaining time N CHAPTER TRACKTITLE SCANX GHTALLA B REPEAT SHUFFLETOTAL REMTRACK TIME N CHAPTER TRACKTITLE SCANX GHTALLA B REPEAT SHUFFLETOTAL REMTRACK TIME TRACKM TITLE INDECHAPTERRACK TRAM TITLE VIDEO SO MCH CD STEREO CD S

19、VCD SVCD SACD SACD playback temporarily interrupted (not active when setting Personal Preferences) first 10 seconds of each track/chapter are played A passage (A-B) is being repeated tracks/chapters are played in random order repeat Title/Chapter/Track/All active FTS (Favourite track selection) prog

20、ram available for CD/DVD/ VCD/SVCD inserted remote control active (flashing) DTS (Digital Theatre Sound) audio on the digital output Sound mode button (for DVD) is set to Multi-channel Sound mode button (for DVD/VCD) is set to Dolby Surround Sound mode button (for DVD/VCD) is set to 3D Sound 3D S SU

21、R MCH DTS F ST CHAPTER TRACKTITLEALLREPEAT SHUFFLET A-B REPEAT SCAN X F ST VGA DIGITAL NATURAL MOTION SACD SVCDCD STEREO MCH CHAPTER TRACKTITLE SCANINDEXCHAPTERTRACKALBUM TITLE HDCDVIDEOAUDIO PIC DTSMCH3DSURSPOTLIGHTALLA-B REPEATGROUP SHUFFLETOTAL REMTRACK TIME Directions for useGB 9SACD 10003. Engl

22、ish 14 PREPARATION Preparation General notes - Depending on your amplifier/receiver/Stereo System there are various ways you could connect the player. These are explained in the chapter below. - For some connections settings for digital and/or analog output are required. These settings have to be ma

23、de in the Personal Preferences menu which is only accessible via your TV screen. In these cases you will need to connect the player to the TV as well. - Please refer to your amplifier/receiver/Stereo System, TV and any other User Manual(s) as necessary to make the optimal connections. Caution: Do no

24、t connect the players audio output to the phono input of your audio system. Connecting to audio equipment - analog Connecting to an amplifier/receiver equipped with two channel analog stereo GConnect the audio Left and Right outputs for Front speaker connection (1) to the corresponding sockets on yo

25、ur amplifier, receiver or stereo system. For this use the audio cable supplied. Connecting to a Multi-channel Audio/(Video) receiver with 6 connectors This SACD player contains a multi-channel decoder. This enables playback of SACDs recorded in Multi-channel. You only need to select Multi-channel us

26、ing the Sound Mode key. 1Connect the audio Left and Right outputs for Front speaker connection (1) to the corresponding input sockets on your receiver. For this use the audio cable supplied. 2Connect the audio Left and Right outputs for Surround speaker connection (2) to the corresponding inputs on

27、your receiver. For this use an optional audio cable. 3Connect the audio outputs for Center speaker and Subwoofer connection (3) to the corresponding inputs on your receiver. For this use an optional audio cable. Note: If the subwoofer is equipped with its own amplifier, the Subwoofer connection shou

28、ld be connected to the subwoofer directly. MAINS VOLTAGE SELECTOR 100-120V220-240V 123 LR I AUX-I/O II TO TV-I/O SUBWRIGHT GND RIGHT SURR.LEFT SURR.CENTERLEFT MULTICHANNEL AUDIO OUT DIG OUTOPT OUT DIGITAL AUDIO OUT PCM/MPEG2/AC3/DTS (CVBS)( Y/C ) VIDEO OUTS-VIDEO AUDIO VIDEO OUTSTEREO OUT FILTER AMP

29、LIFIER 312 MAINS VOLTAGE SELECTOR 100-120V220-240V 123 LR I AUX-I/O II TO TV-I/O SUBWRIGHT GND RIGHT SURR.LEFT SURR.CENTERLEFT MULTICHANNEL AUDIO OUT DIG OUTOPT OUT DIGITAL AUDIO OUT PCM/MPEG2/AC3/DTS (CVBS)( Y/C ) VIDEO OUTS-VIDEO AUDIO VIDEO OUTSTEREO OUT FILTER AMPLIFIER 1 English ON SCREEN DISPL

30、AY INFORMATION 13 On screen display information Menu bar/Status window VUser preference dSound WTrack/TitleePicture by Picture XChapterfSlow motion ZSubtitle languagegFast motion AnglehTime search aZoomYAudio language bColourdSound Mode cVideo FTS Status window icons The status window displays the c

31、urrent status of the player and is displayed together with the first part of the menu bar, if activated in the Features menu (see Personal Preferences). General Disc type Tray status Default screen The default screen is displayed when the player is in STOP mode. It may contain a status window (see S

32、tatus Window) and a Temporary Feedback Field. Giving information concerning prohibited actions, playback modes, available angles, etc. Temporary Feedback Field icons Scan Repeat All Repeat Title Repeat Track Repeat Chapter Shuffle Shuffle Repeat Repeat A to end Repeat A-B Current camera angle/number

33、 of available camera angles Child Lock On Child Safe Resume Action prohibited ? ? ? ? Directions for useGB 10SACD 10003. English 16 PREPARATION Connecting to a TV Notes - Depending on your TV there are various ways you could connect the player. These are shown in the illustration below. - Please ref

34、er to your TV, VCR, and any other User Manual(s) as necessary to make the optimal connections. - Do not connect your SACD-player via your VCR, because the video quality could be distorted by the copy protection system. 1Connect the Euroconnector (TO TV-I/O 6) to the corresponding connector on the TV

35、 using the Euroconnector cable supplied. If your TV is not equipped with a Euroconnector you can select one of the following alternative connections: S-Video (Y/C) connection 1Connect the S-VIDEO OUT (Y/C) socket (7) to the corresponding socket on the TV using an optional S-Video cable. GIf you wish

36、 to receive the sound via your TV connect the STEREO OUT Left and Right output sockets (1) to the corresponding sockets on the TV using the audio cable supplied. Video CVBS connection 1Connect the VIDEO OUT (CVBS) socket (8) to the corresponding socket on the TV using the video cable supplied. 2If y

37、ou wish to receive the sound via your TV connect the STEREO OUT Left and Right output sockets (1) to the corresponding sockets on the TV using the audio cable supplied. 6 Channel settings - DVD only Front speaker L (Large) : When the front speakers can reproduce low frequency signals below 120Hz S (

38、Small) : When the front speakers cannot produce low frequency signals below 120Hz Center Speaker* L (Large) : When the center speaker can reproduce low frequency signals below 120Hz S (Small) : When the center speaker cannot produce low frequency signals below 120Hz Off: When the center speaker is n

39、ot connected Surround speakers L (Large) : When the surround speakers can reproduce low frequency signals below 120Hz S (Small) : When the surround speakers cannot produce low frequency signals below 120Hz Off: When the surround speakers are not connected Subwoofer On: When you connect a subwoofer O

40、ff: When a subwoofer is not connected * You can use your TV as center speaker. Please refer to your TV User Manual to check if your TV can reproduce low frequency signals below 120Hz. If not, set Center Speaker to S(small). When Center Speaker is selected in the Personal Preferences menu, the sound

41、from both center speaker and audio L/R as well as the audio from the Euroconnector will contain the center speaker audio. TV Front speaker right Front speaker left Center speaker Rear speaker (left surround) Rear speaker (right surround) MAINS VOLTAGE SELECTOR 100-120V220-240V 123 LR I AUX-I/O II TO

42、 TV-I/O SUBWRIGHT GND RIGHT SURR.LEFT SURR.CENTERLEFT MULTICHANNEL AUDIO OUT DIG OUTOPT OUT DIGITAL AUDIO OUT PCM/MPEG2/AC3/DTS (CVBS)( Y/C ) VIDEO OUTS-VIDEO AUDIO VIDEO OUTSTEREO OUT FILTER 6781 English PREPARATION 15 Connecting to an amplifier/receiver equipped with Dolby Pro Logic For an amplifi

43、er/receiver with Dolby Surround, you may connect your SACD player in the same way as described for Dolby Pro Logic. Dolby Pro Logic sound 1Connect the audio Left and Right outputs for Front speaker connection (1) to the corresponding inputs on the Dolby Pro Logic Audio/Video amplifier/receiver, usin

44、g the audio cable supplied. 2Set Analog Output to Dolby Surround in the Personal Preferences menu. If your amplifier/receiver is equipped with a Dolby Digital decoder GConnect the player as described in chapter Connecting to an Audio/(Video) receiver with multi channel decoder. If you connect the pl

45、ayer to a TV equipped with a Dolby Pro Logic decoder GConnect the player to the TV as described in chapter Connecting to a TV. Connecting to audio equipment - digital The digital output of the SACD1000 does not provide PCM (Pulse Code Modulation) signals. If your amplifer/receiver can decode only PC

46、M and no multi- channel signals such as Dolby Digital, do not connect your SACD player via the digital input. This could damage your amplifier and/or speakers. Connecting to an Audio/(Video) receiver with multi-channel decoder (Dolby Digital, MPEG 2 and DTS) Digital Multi-channel sound (not for SACD

47、) For this you need a multi-channel A/V receiver that supports one or more of the DVD audio formats supported by your SACD player (MPEG 2, Dolby Digital and DTS). For this you can check the receiver manual and the logos on the front of the receiver. 1Connect the players digital audio output (optical

48、 4 or coaxial 5) to the corresponding input on the receiver. For this use the digital audio cable (coaxial) is supplied. Optical is optional. 2Set Digital Output to ALL in the Personal Preferences menu. Notes: - If the audio format of the digital output does not match the capabilities of your receiv

49、er, the receiver will produce a strong, distorted sound. The audio format of the DVD disc in play is displayed in the Status Window, when changing the audio format. - 6 Channel Digital Surround Sound via digital connection can only be obtained if your receiver is equipped with a Digital Multi-channel decoder. If your receiver does not contain a decoder, you can make the analog connections as described in chapter Connecting to a Multi-channel Audio/(Video) receiver with 6 connectors to obtain 6 Channel Digital Surround Sound. - SACD Multi-channel sound cann