Jvc-RCBX-30-Service-Manual电路原理图.pdf

《Jvc-RCBX-30-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Jvc-RCBX-30-Service-Manual电路原理图.pdf（30页珍藏版）》请在收音机爱好者资料库上搜索。

1、RC-BX30No.21171Dec. 2002COPYRIGHT 2002 VICTOR COMPANY OF JAPAN, LTD.SERVICE MANUALContentsSafety precautionsPreventing static electricityImportant for laser productsDisassembly methodAdjustment methodTrouble shooting1-21-31-41-51-141-17RC-BX30Area suffixUJ - U.S.MilitaryFlow of functional operationu

2、ntil TOC readMaintenance of laser pickupReplacement of laser pickupDescription of major ICsWiring connection1-181-191-191-201-22CD PORTABLE SYSTEMRC-BX301-21. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protectio

3、n, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only.2. Alterations of the design or circuitry of the product should n

4、ot be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom.3. Many electrical and mechanical parts

5、 in the products have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these

6、special safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety charac

7、teristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards.4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving part

8、s and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling.5. Leakage currnet check (Electrical shock hazard testin

9、g)After re-assembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line i

10、solation transformer during this check.Plug the AC line cord directly into the AC outlet. Using a “Leakage Current Tester“, measure the leakage current from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground.

11、 Any leakage current must not exceed 0.5mA AC (r.m.s.).Alternate check methodPlug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor between a

12、n exposed metal part and a known good earth ground.Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and meausre the AC voltage across the resistor. Now,

13、reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1. This equipment has been designed and manufactured to meet international safety standards.2. It is the legal responsibility of the repaire

14、r to ensure that these safety standards are maintained.3. Repairs must be made in accordance with the relevant safety standards.4. It is essential that safety critical components are replaced by approved parts.5. If mains voltage selector is provided, check setting for local voltage.Good earth groun

15、dPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE!Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.In regard with

16、component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the “ “ mark nearby are critical for safety. (This regulation does not correspond to J and C version

17、.)RC-BX301-3Conductive material (conductive sheet) or iron plate(caption)Anti-static wrist strapShort landFiexible wireCD pickup unit5. Attention when traverse unit is decomposed*Please refer to “Disassembly method“ in the text for the CD pickup unit. Apply solder to the short land before the flexib

18、le wire is removedfrom the CD servo board. (If the flexible wire is disconnected without applying solder, the CDpickup unit may be destroyed by static electricity.) In the assembly, be sure to remove solder from the short land after connecting the fiexible wire.Electrostatic discharge (ESD), which o

19、ccurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.Preventing static electricity1. Grounding to prevent damage by static electricityStatic electricity in th

20、e work area can destroy the optical pickup (laser diode) in devices such as CD players.Be careful to use proper grounding in the area where repairs are being performed. 2. About the earth processing for the destruction prevention by static electricityGround the workbench by laying conductive materia

21、l (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it.2-1 Ground the workbench2-2 Ground yourselfUse an anti-static wrist strap to release any static electricity built up in your body.In order to maintain quality during transport and before i

22、nstallation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.)Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power sourc

23、e can easily destroy the laser diode. 3. Handling the optical pickup1.2.Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.Remove solder of the short land on the flexible wire after replacing the optical pickup. For specific details, refer to the r

24、eplacement procedure in the text. Remove the anti-static pin when replacing the traverse unit.Be careful not to take too long a time when attaching it to the connector.Handle the flexible wire carefully as it may break when subjected to strong force.It is not possible to adjust the semi-fixed resist

25、or that adjusts the laser power. Do not turn it.4. Handling the traverse unit (optical pickup)1.2.3.4.RC-BX301-4Important for laser products1.CLASS 1 LASER PRODUCT2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam.3.CAUTION : There are no

26、serviceable parts inside theLaser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions.4.CAUTION : The compact disc player uses invisible laserradiation and is equipped with safety switches whichprevent emission of radiation when the drawer is open and the safe

27、ty interlocks have failed or are defeated. It is dangerous to defeat the safety switches.5.CAUTION : If safety switches malfunction, the laser is able to function.6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation

28、 exposure.VARNING : Osynlig laserstrlning nr denna del r ppnad och sprren r urkopplad. Betrakta ej strlen.VARO : Avattaessa ja suojalukitus ohitettaessa olet alttiina nkymttmlle lasersteilylle.l katso steeseen.ADVARSEL : Usynlig laserstrling ved bning , nr sikkerhedsafbrydere er ude af funktion.Undg

29、udsttelse for strling.ADVARSEL : Usynlig laserstrling ved pning,nr sikkerhetsbryteren er avslott. unng utsettelse for strling.REPRODUCTION AND POSITION OF LABELSCLASS 1LASER PRODUCT!CAUTIONPlease use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck.R

30、C-BX301-5Fig.1Fig.2Fig.3Fig.4Removing the front cabinet assemblyand rear cabinet assembly(See Figs. 2 to 4.)Disassembly methodRemoving the handle (See Fig. 1.)1.2.3.4.5.Remove the eight screws A retaining the front cabinet and rear cabinet assemblies from the rear of the main body. (See Fig.2.)Open

31、the cassette door. (See Fig.3.)Slide the lower part of the front cabinet assembly slightly in the direction of the arrow 1. (See Fig.3.)While removing the front cabinet assembly from the cassette knobs and remove it in the upward direction 2. (See Fig.3.)Disconnect the speaker wire from the connecto

32、r CN401 on the main board. (See Fig.4.)Open the CD door.Lift the handle slightly.While pressing the claws a of the rear cabinet assembly in the direction of the arrow 1, slide the handle in the direction of the arrow 2.1.2.3.CD doorRear cabinet assemblyHandleClaw aClaw a112A AAARear cabinet assembly

33、Cassette knobsRear cabinet assemblyFront cabinet assemblyRear cabinet assemblyFront cabinet assemblyMain boardCN401 21RC-BX301-6Fig.5Fig.6Fig.7Prior to performing the following procedures, remove the front cabinet assembly from the rear cabinet assembly.Removing the right and left speaker assemblies

34、 (See Fig. 5.)1.2.3.From the inside of the front cabinet assembly, remove the six screws B retaining the right and left speaker assemblies.Remove the solders from the soldered sections b of the right and left speaker assemblies, remove the speaker wires.Take out the right and left speaker assemblies

35、.Removing the cassette door gear assembly (See Fig. 6.)1.2.From the inside of the front cabinet assembly, remove the two screws C retaining the cassette door gear assembly.Take out the cassette door gear assembly.Note When attaching the screws C, apply a locking agent to the screws C.Note When attac

36、hing the screws B, apply a locking agent to the screws B.Removing the cassette door(See Fig. 7.)1.2.While pressing the section c of the cassette door in the direction of the arrow, remove the boss d of the cassette door from the section e of the front cabinet assembly.Disengage the boss f of the cas

37、sette door from the section g of the front cabinet assembly.Prior to performing the following procedures, remove the cassette door gear assembly.Note Be sure to hang the spring to the section h before attaching the cassette door to the front cabinet assembly.BBBFront cabinet assemblyCassette door ge

38、ar assemblyCassette door Section eSection cBoss d Boss fSection gSection hSpring Front cabinet assemblyRight speaker assemblyLeft speaker assemblySoldered section bSoldered section bCCBSpeaker wiresRC-BX301-7Fig.10Fig.11Fig.8Fig.9Removing the tuner board(See Figs. 8 to 10.)1.2.3.4.5.From the rear si

39、de of the rear cabinet assembly, remove the screw D retaining the FM antenna.(See Fig.8.)Pull out the band and fine tune knobs from the tuner board. (See Fig.9.)Disconnect the wire from the connector CN101 on the tuner board. (See Fig.9.)Remove the screw E and two screws F retaining the tuner board.

40、 (See Fig.9.)Take out the tuner board, then remove the screw G retaining the antenna connector plate. (See Fig.10.)Prior to performing the following procedures, remove the front cabinet assembly from the rear cabinet assembly.Note When attaching the screws G, apply a locking agent to the screws G.Re

41、moving the main board(See Figs. 9 and 11.)1.2.3.4.5.Disconnect the wire from the connector CN101 on the tuner board. (See Fig.9.)Pull out the volume, DBB and function knobs from the main board. (See Fig.11.)Disconnect the wires from the connectors CN302, CN303 and CN501 on the main board.(See Fig.11

42、.)Remove the solders from the soldered section i connecting the wires to the main board.(See Fig.11.)Remove the three screws H retaining the main board. (See Fig.11.)DGHHFFRear cabinet assemblyRear cabinet assemblyRear cabinet assemblyRear cabinet assemblyMain boardVolume knobDBB knobCN302CN303CN501

43、Function knobSoldered section iFM antennaTuner boardTuner boardAntenna connector plateFine tune knobBand knobCN101FM antenna wireFM antenna wireRC-BX301-8Fig.12Fig.13Fig.14Fig.15Removing the cassette deck/CD mechanism assembly(See Figs.12 and 13.)1.2.3.From the rear side of the rear cabinet assembly

44、, remove the two screws J retaining the cassette deck/CD mechanism assembly. (See Fig.12.)Disconnect the wires from the connectors CN302, CN303 and CN501 on the main board.(See Fig.13.)Remove the two screws K retaining the cassette deck/CD mechanism assembly. (See Fig.13.)Note When attaching the scr

45、ews K, apply a locking agent to the screws K.Removing the display board(See Figs.14 and 15.)1.2.3.4.5.From the bottom side of the CD mechanism assembly, remove the tie bands bundling the wires from the CD mechanism assembly. (See Fig.14.)Disconnect the wires from the connectors BC01, BC02 and BC03 o

46、n the CD servo board.(See Fig.14.)Remove the solders from the soldered section j connecting the wires to the micro switch board.(See Fig.14.)Remove the two screws L retaining the display board. (See Fig.15.)Press the claws k in the direction of the arrow, remove the display board. (See Fig.15.)JCass

47、ette deck/CD mechanism assemblyRear cabinet assemblyRear cabinet assemblyBC01BC02BC03Tie bandsCD mechanism assemblyCassette desk mechanism assemblyTie bandDisplay boardClaws kCD servo boardSoldered section jMicro switchboardCN302CN303CN501Cassette deck/CD mechanism assemblyKLRC-BX301-9Fig.16Fig.17Re

48、moving the cassette board(See Fig. 16.)1.2.3.4.From the back side of the cassette deck mechanism assembly, remove the tie band bundling the wires.Remove the solders from the soldered section m connecting the wires of the capstan motor and leaf switch.Remove the four screws M retaining the cassette b

49、oard.From the reverse side of the cassette board, remove the solders from the soldered section n connecting the wires of the REC/PB head.Removing the cassette deck mechanism assembly (See Fig. 17.)1.2.3.Remove the solders from the soldered section p connecting the wires of the leaf switch.Remove the solders from the soldered section q connecting the wires of the REC/PB head.Remove the two screws N retaining