Jvc-THM-55-Service-Manual电路原理图.pdf

《Jvc-THM-55-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Jvc-THM-55-Service-Manual电路原理图.pdf（105页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LIMITEDNo.MB0752003/11DVD DIGITAL THEATER SYSTEMMB075200310TH-M55TABLE OF CONTENTS1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32 S

2、PECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-73 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-84

3、 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-345 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4、. . . 1-39Area suffixJ - U.S.A.C - CanadaXV-THM55 SP-PWM55SP-THM55C SP-THM55F SP-THM55F SP-THM55F SP-THM55F1-2 (No.MB075)SPECIFICATIONDesign and specifications are subject to change without notice.Center unitAudio sectionTotal Harmonic Distortion 0.02%NOTE : This value is measured at System cord CON

5、NECTOR for reference.Audio input sensitivity/Impedance (at 1 kHz)Analog input AUDIO IN (VCR) 290 mV/47 kDigital input* DIGITAL IN (DBS) (OPTICAL) -21 dBm to -15 dBm (660 nm 30 nm)* Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency - 32 kHz, 44.1 kHz, 48 kH

6、z)Video sectionColor System NTSCHorizontal Resolution 500 linesSignal-to-Noise Ratio 64 dBVideo output level Composite 1.0 V(p-p)/75 S-video-Y 1.0 V(p-p)/75 S-video-C 0.286 V(p-p)/75 Component-Y 1.0 V(p-p)/75 Component-PB/PR 0.7 V(p-p)/75 Video input sensitivity/Impedance (VCR IN)Composite 1.0 V(p-p

7、)/75 S-video-Y 1.0 V(p-p)/75 S-video-C 0.286 V(p-p)/75 Tuner sectionTuning Range FM 87.5 MHz to 108.0 MHzAM 530 kHz to 1710 kHzGeneralPower Requirements AC 120 V, 60 HzPower Consumption 20 W (at operation), 1.0 W (in standby mode)Dimensions (W H D) 400 mm 85 mm 386 mm (15-3/4 inches 3-3/8 inches 15-

8、1/14 inches)Mass 4.6 kg (10.2 lbs)SubwooferAmplifier sectionFront/Center/Surround 100 W per channel, RMS at 4 at 1 kHz, with 10 % total harmonic distortion.Subwoofer 120 W, RMS at 4 at 100 Hz, with 10 % total harmonic distortion.Speaker sectionSpeaker unit 16 cm (6-5/16 inches) Bass-reflex, Magnetic

9、ally ShieldedFrequency Range 30 Hz to 200 HzGeneralPower Requirements AC 120 V, 60 HzPower Consumption 150 W (at operation), 0 W (in standby mode)Dimensions (W H D) 216 mm 353 mm 485 mm (8-9/16 inches 13-15/16 inches 19-1/8 inches)Mass 12.0 kg (26.5 lbs)Satellite SpeakerSpeakers Woofer 10.0 cm (3-15

10、/16 inches)Tweeter 4.0 cm (1-5/8 inches) Bass-reflex, Magnetically ShieldedPower Handling Capacity 100 WImpedance 4 Frequency Range 65 Hz to 20 kHzDimensions (W H D) 140 mm 228 mm 167 mm (5-9/16 inches 9 inches 6-5/8 inches)Mass 1.9 kg (4.2 lbs)Center SpeakerSpeakers Woofer 8.0 cm (3-3/16 inches) 2T

11、weeter 4.0 cm (1-5/8 inches) Bass-reflex, Magnetically ShieldedPower Handling Capacity 100 WImpedance 4 Frequency Range 65 Hz to 20 kHzDimensions (W H D) 326 mm 119 mm 164 mm (12-7/8 inches 4-11/16 inches 6-1/2 inches)Mass 2.4 kg (5.3 lbs)AccessoriesRemote control (1), Batteries (2), FM antenna (1),

12、 AM loop antenna (1), Power cord (1), System cord (1), Composite video cord (1)Speaker codes (1)5 m (16 ft) For satellite (front left/right) and center speakers (3)10 m (32 ft) For satellite speakers (surround left/right) (2) (The length of the above speaker cords are approximate.)(No.MB075)1-3SECTI

13、ON 1PRECAUTION1.1 Safety Precautions(1) This design of this product contains special hardware andmany circuits and components specially for safety purpos-es. For continued protection, no changes should be madeto the original design unless authorized in writing by themanufacturer. Replacement parts m

14、ust be identical tothose used in the original circuits. Services should be per-formed by qualified personnel only.(2) Alterations of the design or circuitry of the product shouldnot be made. Any design alterations of the product shouldnot be made. Any design alterations or additions will voidthe man

15、ufacturers warranty and will further relieve themanufacture of responsibility for personal injury or propertydamage resulting therefrom.(3) Many electrical and mechanical parts in the products havespecial safety-related characteristics. These characteris-tics are often not evident from visual inspec

16、tion nor can theprotection afforded by them necessarily be obtained by us-ing replacement components rated for higher voltage, watt-age, etc. Replacement parts which have these specialsafety characteristics are identified in the Parts List of Ser-vice Manual. Electrical components having such featur

17、esare identified by shading on the schematics and by ( ) onthe Parts List in the Service Manual. The use of a substitutereplacement which does not have the same safety charac-teristics as the recommended replacement parts shown inthe Parts List of Service Manual may create shock, fire, orother hazar

18、ds.(4) The leads in the products are routed and dressed with ties,clamps, tubings, barriers and the like to be separated fromlive parts, high temperature parts, moving parts and/orsharp edges for the prevention of electric shock and firehazard. When service is required, the original lead routingand

19、dress should be observed, and it should be confirmedthat they have been returned to normal, after reassem-bling.(5) Leakage shock hazard testingAfter reassembling the product, always perform an isola-tion check on the exposed metal parts of the product (an-tenna terminals, knobs, metal cabinet, scre

20、w heads,headphone jack, control shafts, etc.) to be sure the productis safe to operate without danger of electrical shock.Do notuse a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using a“Leakage Current Tester“, measure the leakage currentfrom each

21、 exposed metal parts of the cabinet, particular-ly any exposed metal part having a return path to thechassis, to a known good earth ground. Any leakage cur-rent must not exceed 0.5mA AC (r.m.s.). Alternate check methodPlug the AC line cord directly into the AC outlet. Use anAC voltmeter having, 1,00

22、0 per volt or more sensitivityin the following manner. Connect a 1,500 10W resistorparalleled by a 0.15F AC-type capacitor between an ex-posed metal part and a known good earth ground.Measure the AC voltage across the resistor with the ACvoltmeter. Move the resistor connection to each exposed metalp

23、art, particularly any exposed metal part having a returnpath to the chassis, and measure the AC voltage acrossthe resistor. Now, reverse the plug in the AC outlet andrepeat each measurement. Voltage measured any mustnot exceed 0.75 V AC (r.m.s.). This corresponds to 0.5mA AC (r.m.s.). 1.2 Warning(1)

24、 This equipment has been designed and manufactured tomeet international safety standards.(2) It is the legal responsibility of the repairer to ensure thatthese safety standards are maintained.(3) Repairs must be made in accordance with the relevantsafety standards.(4) It is essential that safety cri

25、tical components are replacedby approved parts.(5) If mains voltage selector is provided, check setting for localvoltage.1.3 CautionBurrs formed during molding may be left over on some partsof the chassis. Therefore, pay attention to such burrs in the case of pre-forming repair of this system.1.4 Cr

26、itical parts for safetyIn regard with component parts appearing on the silk-screenprinted side (parts side) of the PWB diagrams, the parts that areprinted over with black such as the resistor ( ), diode ( )and ICP ( ) or identified by the “ “ mark nearby are criticalfor safety. When replacing them,

27、be sure to use the parts of thesame type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version)Good earth groundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE1-4 (No.MB075)1.5 Preve

28、nting static electricity1.5.1 Grounding to prevent damage by static electricityElectrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laserdiode in the traverse unit (optical pickup). Take care to prevent this when performi

29、ng repairs.1.5.2 About the earth processing for the destruction prevention by static electricityStatic electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players.Be careful to use proper grounding in the area where repairs are being performed. (1) Ground

30、 the workbenchGround the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing thetraverse unit (optical pickup) on it.(2) Ground yourselfUse an anti-static wrist strap to release any static electricity built up in your body.1.5.3 Handling the o

31、ptical pickup(1) In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pick-up are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.)(2) Do not use a tester to check the cond

32、ition of the laser diode in the optical pickup. The testers internal power source can easilydestroy the laser diode.1.5.4 Handling the traverse unit (optical pickup)(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.(2) Remove solder of the sho

33、rt lands on the flexible wire after replacing the optical pickup. For specific details, refer to the replace-ment procedure in the text. Remove the anti-static pin when replacing the traverse unit.Be careful not to take too long a time when attaching it to the connector.(3) Handle the flexible wire

34、carefully as it may break when subjected to strong force.(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.1.5.5 Attention when traverse unit is decomposed*Please refer to “Disassembly method“ in the text for the DVD pickup. Apply solder to the sho

35、rt circuit points before the flexible wire is disconnected from the connector on the DVD pickup. (If the flexible wire is disconnected without applying solder, the DVD pickup may be destroyed by static electricity.) In the assembly, be sure to remove solder from the short circuit points after connec

36、ting the flexible wire.Conductive material (conductive sheet) or iron plate(caption)Anti-static wrist strapDVD pickupDVD changer mechanism assemblyShort circuit points(No.MB075)1-51.6 Important for laser products1.CLASS 1 LASER PRODUCT2.DANGER : Invisible laser radiation when open and inter lock fai

37、led or defeated. Avoid direct exposure to beam.3.CAUTION : There are no serviceable parts inside theLaser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions.4.CAUTION : The compact disc player uses invisible laserradiation and is equipped with safety switches

38、 whichprevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches.5.CAUTION : If safety switches malfunction, the laser is able to function.6.CAUTION : Use of controls, adjustments or performance of proced

39、ures other than those specified herein may result in hazardous radiation exposure.!Please use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck.1-6 (No.MB075)1.7 Importance administering point on the safetyCaution: For continued protection against ris

40、k offire, replace only with same type 1.6A/125V forF901, 6.3A/125V for F101, 8A/125V for F153 andF154.This symbol specifies type of fast operating fuse.Precaution: Pour eviter risques de feux, remplacezle fusible de surete de F901 comme le meme typeque 1.6A/125V, et 6.3A/125V pour F101, et 8A/125Vpo

41、ur F153 et F154.Ce sont des fusibles suretes qui functionnes rapide.Power supply board (Forward side)F901F101Speaker terminal board (Forward side)F153 F154Mother board (Forward side)(No.MB075)1-7SECTION 2SPECIFIC SERVICE INSTRUCTIONSThis service manual does not describe SPECIFIC SERVICE INSTRUCTIONS

42、.1-8 (No.MB075)SECTION 3DISASSEMBLY3.1 Main body section3.1.1 Removing the metal cover (See Figs.1 to 4)(1) From the right and left sides of the main body, remove thefour screws A attaching the metal cover. (See Figs.1 and2.)(2) From the back side of the main body, remove the threescrews B attaching

43、 the metal cover. (See Fig.3.)(3) Lift the rear section of the metal cover in the direction of thearrow while extending the lower sections of the metal cov-er, release the claws a using a longer screwdriver from theinside as required. (See Fig.4.)Note:Do not damage any parts and boards inside the ma

44、in bodywhen releasing the joints a using a longer screwdriver.Fig.1Fig.2Fig.3Fig.4Metal coverAMetal coverAMetal coverRear panelBMetal coverClaws a Claws a(No.MB075)1-93.1.2 Removing the front panel assembly (See Figs.5 and 6) Remove the metal cover.(1) From the top side of the main body, disconnect

45、the parallelwires from the connectors (CN408, CN409) on the mainboard. (See Fig.5.)(2) Disconnect the card wires from the connectors (CN407,CN412) on the main board. (See Fig.5.)(3) Remove the screw C attaching the earth wire to the mainboard. (See Fig.5.)(4) From the bottom side of the main body, r

46、emove the threescrews D attaching the front panel assembly. (See Fig.6.)(5) Release the two hooks b and hook c from the both and bot-tom sides of the main body, and remove the front panel as-sembly in the direction of the arrow. (See Figs.5 and 6.)Fig.5Fig.6CN407CN412CN409CN408Hook bHook bMain board

47、CCard wireEarthwireParallel wiresFront panel assemblyCard wireHook cFront panelassemblyD1-10 (No.MB075)3.1.3 Removing the DVD changer mechanism assembly (See Fig.7) Remove the metal cover. Remove the front panel assembly.(1) From the top side of the main body, disconnect the cardwires from the conne

48、ctors (CN405, CN415) on the mainboard.(2) Remove the four screws E attaching the DVD changermechanism assembly to the bottom chassis.(3) Take out the DVD changer mechanism assembly in an up-ward direction.Note:When attaching the screw E, fit the hole of the DVD changermechanism assembly to the bosse

49、s d on the bottom chassis.Fig.73.1.4 Removing the rear panel (See Fig.8) Remove the metal cover.(1) From the back side of the main body, remove the screw F,nine screws G and three screws H attaching the rear panel.Fig.8Main boardBoss dBoss dCN405CN415Bottom chassisDVD changer mechanismassemblyCard wiresEEEFGGHHHRear panel