Jvc-UXP-4-R-Service-Manual电路原理图.pdf

《Jvc-UXP-4-R-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Jvc-UXP-4-R-Service-Manual电路原理图.pdf（74页珍藏版）》请在收音机爱好者资料库上搜索。

1、1-1UX-P4RSERVICE MANUALMICRO COMPONENT SYSTEMNo.20975Jun. 2001COPYRIGHT 2001 VICTOR COMPANY OF JAPAN, LTD.UX-P4RUX-P4RContentsSafety precautionsPreventing static electricityImportant for laser productsDisassembly methodMain adjustmentFlow of functional operation until TOC read (CD)Maintenance of las

2、er pickupReplacement of laser pickup Description of major ICsInternal connection of display1-21-41-61-71-141-181-191-191-201-39Area SuffixEENContinental EuropeNorthern EuropeCOMPACTDIGITAL AUDIOCD TAPE FM/AMMICRO COMPONENT SYSTEM UXP4RCD-R/RW PLAYBACKAUXTIMERCLOCKSTANDBYSTANDBY / ONVOLUMEFUNCTIONSOU

3、NDDIRECT OPERATINGAHB PROAUTO REVERSEAUTO TAPE SELECTORRECREV.MODEPHONESSLEEPSTANDBY/ONAUXFM/AMTAPECDDISPLAYREPEATRANDOMPROGFM MODEAUTOPRESETSOUNDMODECDCANCEL MULTI KEY SETPTY/EONDISPLAYMODERM-SUXP3R REMOTE CONTROLVOLUMEAHBPRO/SP-UXP4 CA-UXP4R SP-UXP41-2UX-P4R1. This design of this product contains

4、special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be

5、 performed by qualified personnel only.2. Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsib

6、ility for personal injury or property damage resulting therefrom.3. Many electrical and mechanical parts in the products have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by

7、using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts Li

8、st in the Service Manual. The use of a substitute replacement which does not have the same safety characteristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards.4. The leads in the products are routed and dressed with ties, cla

9、mps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they ha

10、ve been returned to normal, after re-assembling.5. Leakage currnet check (Electrical shock hazard testing)After re-assembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts

11、, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check.Plug the AC line cord directly into the AC outlet. Using a “Leakage Current Tester“, measure the leakage current from each exposed metal parts of the cabinet

12、, particularly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.).Alternate check methodPlug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more sensitivity

13、in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor between an exposed metal part and a known good earth ground.Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to eachexposed metal part, particularly any expose

14、d metal part having a return path to the chassis, and meausre the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1. This equipment has been designed a

15、nd manufactured to meet international safety standards.2. It is the legal responsibility of the repairer to ensure that these safety standards are maintained.3. Repairs must be made in accordance with the relevant safety standards.4. It is essential that safety critical components are replaced by ap

16、proved parts.5. If mains voltage selector is provided, check setting for local voltage.Good earth groundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE!Burrs formed during molding may be left over on some parts of the chassis.

17、 Therefore, pay attention to such burrs in the case of preforming repair of this system.In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified

18、by the “ “ mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer. (Except the J and C version)1-3UX-P4R1. Service should be performed by qualified personnel only.2. This equipment has been designed and manufact

19、ured to meet international safety standards.3. It is the legal responsibility of the repairer to ensure that these safety standards are maintained.4. Repairs must be made in accordance with the relevant safety standards.5. It is essential that safety critical components are replaced by approved part

20、s.6. If mains voltage selector is provided, check setting for local voltage.1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing

21、 by the manufacturer. Replacement parts must be identical to those used in the original circuits. 2. Any unauthorised design alterations or additions will void the manufacturers guarantee ; furthermore the manufacturer cannot accept responsibility for personal injury or property damage resulting the

22、refrom.3. Essential safety critical components are identified by ( ) on the Parts List and by shading on the schematics, and must never be replaced by parts other than those listed in the manual. Please note however that many electrical and mechanical parts in the product have special safety related

23、 characteristics. These characteristics are often not evident from visual inspection. Parts other than specified by the manufacturer may not have the same safety characteristics as the recommended replacement parts shown in the Parts List of the Service Manual and may create shock, fire, or other ha

24、zards.4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routi

25、ng and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling.!Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.(U.K only)1-4UX-P

26、4RPreventing static electricityElectrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.1.1. Grounding to prevent damage by

27、static electricityStatic electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players. Be careful to use proper grounding in the area where repairs are being performed. 1.1.1. Ground the workbench1. Ground the workbench by laying conductive material (such

28、as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it.1.1.2. Ground yourself1. Use an anti-static wrist strap to release any static electricity built up in your body. 1.1.3. Handling the optical pickup1. In order to maintain quality during transport

29、and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.)2. Do not use a tester to check the condition of the laser diode in the optical pickup. The testers inter

30、nal power source can easily destroy the laser diode. 1.2. Handling the traverse unit (optical pickup)1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. 2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing the op

31、tical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. 3. Handle the flexible cable carefully as it may break when subjected to strong

32、force. 4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn itConductive material (conductive sheet) or iron plate(caption)Anti-static wrist strap1-5UX-P4R1.3. Cautions on removing the CD traverse unit* For removing the CD traverse unit in detail, refer t

33、o the “Adjustment Method“ section of this manual.1. Before disconnecting the flexible wire from the connector CN601 on the CD SERVO board, solder the part shown in the figure below.(Note:If the flexible wire is disconnected from the CN601 without presoldering, it may cause breakdown of the CD pickup

34、 assembly.)2. When reassembling the CD traverse unit, be sure to remove the solder from the soldered part after reconnecting the flexible wire to the CN601. CD SERVO boardCD SERVO boardSoldering partCN601CN601C601C602C603C604C605C606C607C610C611C612C613C614C615C616C617C619C620C621C622C623C624C631C63

35、2C633C641 C642C643B619C651C652C653C654C655C656C657C658C661C663C664C665C667C668C669C670C671C672C673C676C677C679C680C691C692C693C694C695C696C699C801C802C811C812C813C814C815C821 C822C823C824C831C832C833CN601CN651CN652CN801D831R648IC652IC801IC802L831Q631Q801R601R602R603R604R605R606R610R611R612 R613R617R

36、618R619R620R621R631R632R634R635R636R641R642R643R647R651R652R653R654R655R656R657R658R659R661R662R663R664R665R666R667R668R669R670R682R683R685R691R692R695R696R701R702R703R704R705R706R707R708R709R710R801R802R803R804R805R806R807 R808R809R812R821R822R823R824R831W605CN606X651B604B616B614R813C816B613B615B61

37、0B612B617B618IC601R607B601B603B602B611B609B608B607B606B605D601D602R681C681 R684MUTEFLAGCDDGBLKCK/RESTMLDMDATAMCLKCDDGSUBQSQCK/RSTSTATFM+RESTSM-SM+D.GNDFM-11111BEBEC316ARFA.GNDF- T- T+ F+ GND VR LD MD T2 K F1 NC T1 SR F2115T02SCDSCDCDDG13LM+OPSWGNDCLSWLM-M.GNDSW10SW10CLOSEOPENOPSWCLSECD+BCD+BCDLA.GND

38、A.GNDCDR5111612141611716321224131-6UX-P4RImportant for laser products1.CLASS 1 LASER PRODUCT2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam.3.CAUTION : There are no serviceable parts inside theLaser Unit. Do not disassemble the Laser Un

39、it. Replace the complete Laser Unit if it malfunctions.4.CAUTION : The compact disc player uses invisible laserradiation and is equipped with safety switches whichprevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat th

40、e safety switches.5.CAUTION : If safety switches malfunction, the laser is able to function.6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.VARNING : Osynlig laserstrlning r denna del r ppnad och sprre

41、n r urkopplad. Betrakta ej strlen.VARO : Avattaessa ja suojalukitus ohitettaessa olet alttiina nkymttmlle lasersteilylle.l katso steeseen.ADVARSEL : Usynlig laserstrling ved bning , nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling.ADVARSEL : Usynlig laserstrling ved pning,nr sik

42、kerhetsbryteren er avslott. unng utsettelse for strling.REPRODUCTION AND POSITION OF LABELSWARNING LABEL!CAUTIONPlease use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck.1-7UX-P4RRemove the six screws A on the back of the body.Remove the two screws

43、 B on the side of the body.Pull both sides of the metal cover outward and lift the rear part of the cover.1.2.3.Disassembly methodRemoving the metal cover (See Fig.1 and 2)Prior to performing the following procedure, remove the metal cover.Remove the two screws C on the back of the body.1.Removing t

44、he rear cover (See Fig.3)Fig.1Fig.2Fig.3AAAAAMetal coverMetal coverB 2CRear coverRear panelC1-8UX-P4RPrior to performing the following procedure, remove the metal cover.Disconnect the card wire from connector CN1 on the tuner board.Remove the screw D on the right side of the body.Remove the two scre

45、ws E on the rear panel.1.2.3.Removing the tuner board (See Fig.4 and 5)Prior to performing the following procedure, remove the metal cover and the rear cover.Disconnect the card wires from connector CN903, CN904 on the main board on the upper side of the body.Remove the screw D attaching the tuner b

46、oard and the CD mechanism on the right side of the body.Remove the two screws F attaching the rear panel and the CD mechanism on the back of the body.Move the rear part of the CD mechanism assembly upwards to disengage the two joints a and release from the rear panel.Pull the front panel toward the

47、front and move the rear part of the CD mechanism assembly upwards. Then pull out the CD mechanism assembly from the front panel backward.1.2.3.4.Removing the CD mechanism assembly (See Fig.6 to 8)To remove the CD mechanism assembly efficiently, disconnect the card wireconnecting the tuner board with

48、 the main board in advance.REFERENCE: Fig.4Fig.5Fig.6Fig.7DCN1Tuner boardERear coverRear panelRear panelTuner boardCard wiresCD mechanism assemblyFront panel assemblyCN903Main boardCN904CD mechanism assemblyTuner boardDFront panel assembly1-9UX-P4RPrior to performing the following procedure, remove the metal cover, rear cover and the CD mechanism assembly.Remove the five screws G attaching the rear panel.Disconnect the card wire from CN902 on the main board.Disengage the lower two joints b on each side of the rear panel using a screwdriver and remove the rear panel backward (The tune