《Jvc-THS-5-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Jvc-THS-5-Service-Manual电路原理图.pdf（30页珍藏版）》请在收音机爱好者资料库上搜索。
1、SERVICE MANUALCOPYRIGHT 2004 VICTOR COMPANY OF JAPAN, LIMITEDNo.MB1802004/4DVD DIGITAL CINEMA SYSTEMMB18020044TH-S5, TH-S51TABLE OF CONTENTS1 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32
2、 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-73 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-
3、84 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-255 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4、. . . . 1-29Area suffixB - U.K.TH-S51Area suffixB - U.K.E - Continental EuropeEN - Northern EuropeEV - Eastern EuropeTH-S5TH-S5 TH-S511-2 (No.MB180)SPECIFICATIONCenter unit (XV-THS5/XV-THS51)*1 : This value is measured at System cord CONNECTOR for reference.*2 : Corresponding to Linear PCM, Dolby Di
5、gital, and DTS Digital Surround (with sampling frequency - 32 kHz, 44.1 kHz, 48 kHz)Subwoofer (SP-PWS5/SP-PWS51)Satellite SpeakersDesigns furthermore the manufacturer cannotaccept responsibility for personal injury or property damage resulting therefrom.(3) Essential safety critical components are i
6、dentified by ( ) on the Parts List and by shading on the schematics, and must neverbe replaced by parts other than those listed in the manual. Please note however that many electrical and mechanical parts inthe product have special safety related characteristics. These characteristics are often not
7、evident from visual inspection. Partsother than specified by the manufacturer may not have the same safety characteristics as the recommended replacement partsshown in the Parts List of the Service Manual and may create shock, fire, or other hazards.(4) The leads in the products are routed and dress
8、ed with ties, clamps, tubings, barriers and the like to be separated from live parts,high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service isrequired, the original lead routing and dress should be observed, and it should be confirm
9、ed that they have been returned tonormal, after re-assembling.1.5.1 Warning(1) Service should be performed by qualified personnel only.(2) This equipment has been designed and manufactured to meet international safety standards.(3) It is the legal responsibility of the repairer to ensure that these
10、safety standards are maintained.(4) Repairs must be made in accordance with the relevant safety standards.(5) It is essential that safety critical components are replaced by approved parts.(6) If mains voltage selector is provided, check setting for local voltage.Burrs formed during molding may be l
11、eft over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.(No.MB180)1-51.6 Preventing static electricityElectrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy
12、the laserdiode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.1.6.1 Grounding to prevent damage by static electricityStatic electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products. Be careful to use proper
13、grounding in the area where repairs are being performed. (1) Ground the workbenchGround the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing thetraverse unit (optical pickup) on it.(2) Ground yourselfUse an anti-static wrist strap to releas
14、e any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement opticalpickup are shorted. After replacement, return the shorted parts to their original condition.
15、(Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easilydestroy the laser diode. 1.7 Handling the traverse unit (optical pickup)(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it
16、is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to thereplacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
17、time when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.1.8 Attention when traverse unit is decomposed*Please refer to “Disa
18、ssembly method“ in the text for the pickup unit. Apply solder to the short land sections before the flexible wire is disconnected from the connecto on the servo board. (If the flexiblewire is disconnected without applying solder, the pickup may be destroyed by static electricity.) In the assembly, b
19、e sure to remove solder from the short land sections after connecting the flexible wire.1MConductive material(conductive sheet) or iron palate(caption)Anti-static wrist strapTraverse mechanism assemblyPickupShort land section c1-6 (No.MB180)1.9 Important for laser products1.CLASS 1 LASER PRODUCT2.DA
20、NGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam.3.CAUTION : There are no serviceable parts inside theLaser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions.4.CAUTION : The CD,MD and DVD player uses
21、 invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches.5.CAUTION : If safety switches malfunction, the laser is able to function.6
22、.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure.REPRODUCTION AND POSITION OF LABELSCAUTION : Visible and Invisible laser radiation when open and interlock failed or defeated.AVOID DIRECT EXPOSURE TO BE
23、AM. (e)VARNING : Synlig ochosynling laserstrlning nr den ppnas och sprren rurkopplad. Betrakta ejstrlen. (s)VARO : Avattaessa ja suojalukitusohitettuna tai viallisena olet alttiina nkyvlle ja nkymttmllelasersteilylle. Vlt steenkohdistumista suoraan itseesi. (f)ADVARSEL : Synlig og usynliglaserstrlin
24、g nr maskinen erben eller interlocken fejeler.Undg direkte eksponering til strling. (d)!Please use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck.CLASS 1LASER PRODUCTCAUTION : Visible and Invisible laser radiation when open and interlock failed or
25、defeated.AVOID DIRECT EXPOSURE TO BEAM. (e)VARNING : Synlig ochosynling laserstrlning nr den ppnas och sprren rurkopplad. Betrakta ejstrlen. (s)VARO : Avattaessa ja suojalukitusohitettuna tai viallisena olet alttiina nkyvlle ja nkymttmllelasersteilylle. Vlt steenkohdistumista suoraan itseesi. (f)ADV
26、ARSEL : Synlig og usynliglaserstrling nr maskinen erben eller interlocken fejeler.Undg direkte eksponering til strling. (d)WARNING LABEL(No.MB180)1-7SECTION 2SPECIFIC SERVICE INSTRUCTIONSThis service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.1-8 (No.MB180)SECTION 3DISASSEMBLY3.1 Main bo
27、dy section3.1.1 Removing the top cover (See Figs.1 to 3)(1) From the both sides of the main body, remove the fourscrews A attaching the top cover. (See Figs.1 and 2)(2) From the back side of the main body, remove the threescrews B attaching the top cover. (See Fig.3)(3) Lift the rear section of the
28、top cover upward while extend-ing the lower sections of the top cover. (See Fig.3)Fig.1Fig.2Fig.3ATop coverATop coverB Top cover(No.MB180)1-93.1.2 Removing the front panel assembly (See Figs.4 and 5) Prior to performing the following procedures, remove the topcover.(1) From the top side of the main
29、body, disconnect the parallelwires from the connectors CN451 and CN452 on the mainboard. (See Fig.4)(2) Remove the screw C attaching the earth wire to the mainboard. (See Fig.4)Reference:When attaching the screw C, attach the earth wire withit. (See Fig.4)(3) From the bottom side of the main body, r
30、emove the fourscrews D attaching the front panel assembly. (See Fig.5)(4) Remove the front panel assembly in the direction of the ar-row while releasing the joint a. (See Fig.5)Fig.4Fig.53.1.3 Removing the rear panel (See Fig.6) Prior to performing the following procedures, remove the topcover.(1) F
31、rom the back side of the main body, remove the fourscrews E, screw F and ten screws G attaching the rearpanel.Fig.6CCN452Earth wireFront panel assemblyCN451Main boardDDJoint aFront panel assemblyEGRear panelFG1-10 (No.MB180)3.1.4 Removing the DSP board (See Figs.7 and 8) Prior to performing the foll
32、owing procedures, remove the topcover.(1) From the back side of the main body, remove the screw Fand three screws H attaching the DSP board to the rearpanel. (See Fig.7)(2) From the top side of the main body, remove the screw J at-taching the DSP board to the main body. (See Fig.8)(3) Take out the D
33、SP board, and disconnect the card wiresfrom the connectors CN441 and CN442 on the DSP board.(See Fig.8)3.1.5 Removing the tuner (See Figs.7 and 9) Prior to performing the following procedures, remove the topcover and DSP board.(1) From the back side of the main body, remove the twoscrews K attaching
34、 the tuner to the rear panel. (See Fig.7)(2) From the top side of the main body, disconnect the cardwire from the connector CN410 on the main board. (SeeFig.9)(3) Take out the tuner from the main body.3.1.6 Removing the DVD mechanism assembly (See Fig.9) Prior to performing the following procedures,
35、 remove top coverand DSP board.(1) From the top side of the main body, disconnect the cardwires from the connectors CN401 to CN403, CN408 andCN409 on the main board.(2) Remove the three screws L attaching the DVD mechanismassembly on the main body.(3) Take out the DVD mechanism assembly to the upward di-rection.Note:When attaching the DVD mechanism assembly, connect thecard wires to the connectors at first.Fig.7Fig.8Fig.9FHKJCN441 CN442DSP boardM
免费区 
