《Philips-BDP-2985-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-BDP-2985-Service-Manual电路原理图.pdf（41页珍藏版）》请在收音机爱好者资料库上搜索。
1、TABLE OF CONTENTS Page Service Manual . Mechanical and Dismantling Instructions.3-1 . Software Upgrades .4-1 . Trouble Shooting Chart.5-1 . Wiring Diagram.6-1 . Electrical Diagrams and Print-layouts.7-1 . Set Mechanical Exploded view & Part list.10-1 Copyright 2011 Philips Consumer Electronics B.V.
2、Eindhoven, The Netherlands All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. CLASS 1 LASER PRODUCT PHILIPS GB . DFU I
3、nstruction.2-1 . Revision List.11-1 Home Theater BD Player . Technical Specifications.1-3 . Safety Instruction, Warning & Notes.1-4 . Location of PCB Boards&Version Variation and Repair Scenario Matrix.1-2 Published by Arya & Stephen - 1234 BU AVM Printed in The Netherlands Subject to modification 3
4、141 785 38500 Version 1.0 Service BDP2985/F7 . Votages and Waveforms for Connection Pins.8-1 . Pin Description & Block Diagrams of ICs.9-1 VERSION VARIATIONS Type / Versions BDP2985 Service Police /F7 MAIN BOARD M PF BOARD M LOADER M Tips ：Board in used C - Component Lever Repair M - Module Lever Re
5、pair X - UsedSpecifications Note Region code Blu-ray Countries Canada Playable media media File format Video Audio A USB Main unit Accessories supplied Remote control and 2 AAA batteries 1-3Safety instruction 1. General safety Safety regulations require that during a repair: . Connect the unit to th
6、e mains via an isolation transformer. . Replace safety components indicated by the symbol , only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard. Safety regulations require that after a rep
7、air, you must return the unit in its original condition. Pay, in particular, attention to the following points: . Route the wires/cables correctly, and fix them with the mounted cable clamps. . Check the insulation of the mains lead for external damage. . Check the electrical DC resistance between t
8、he mains plug and the secondary side: 1) Unplug the mains cord, and connect a wire between the two pins of the mains plug. 2) Set the mains switch the “on” position (keep the mains cord unplug). 3) Measure the resistance value between the mains plug and the front panel, controls, and chassis bottom.
9、 4) Repair or correct unit when the resistance measurement is less than 1M . 5) Verify this, before you return the unit to the customer/user (ref. UL-standard no. 1492). 6) Switch the unit “off”, and remove the wire between the two pins of the mains plug. 2.Laser safety This unit employs a laser. On
10、ly qualified service personnel may remove the cover, or attempt to service this device (due to possible eye injury). Laser device unit T ype : Semiconductor laser GaAlAs Wavelength : 650nm (DVD) : 780nm (VCD/CD) Output power : 7mW (DVD) : 10mW (DVD /CD) Beam divergence: 60 degree Note: Use of contro
11、ls or adjustments or performance of procedure other than those specified herein, may result in hazardous radiation exposure. Avoid direct exposure to beam. Safety instruction, Warning & Notes 1-4Warning 1.General . All ICs and many other semiconductors are susceptible to electrostatic discharges (ES
12、D). Careless handing during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: 1) Complete kit ESD3 (small tablem
13、at, wristband, connection box, extension cable and earth cable) 4822 310 10671. 2) Wristband tester 4822 344 13999. . Be careful during measurements in the live voltage section. The primary side of the power supply , including the heat sink, carries live mains voltage when you connect the player to
14、the mains (even when the player is “off”!). It is possible to touch copper tracks and/or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A “lighting stroke” and a stripe-marked
15、printing on the printed wiring board, indicate the primary side of the power supply. . Never replace modules, or components, while the unit is “on”. 2. Laser . The use of optical instruments with this product, will increase eye hazard. . Only qualified service personnel may remove the cover or attem
16、pt to service this device, due to possible eye injury. . Repair handing should take place as much as possible with a disc loaded inside the player. . Text below is placed inside the unit, on the laser cover shield: Notes: Manufactured under licence from Dolby Laboratories. The double-D symbol is tra
17、demarks of Dolby Laboratories, Inc. All rights reserved. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN, AVOID EXPOSURE TO BEAM. 1-5 Solder Joint 1-6Lead-Free requirement for service INDENTIFICATION: Regardless of special logo (not always indicated) One must treat all sets from 1.1.2005 on
18、wards, according next rules. Important note: In fact also products a little older can also be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this. Due to lead-free technology some rules have to be
19、respected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops should be avoided because paste i
20、s not easy to store and to handle. Use only adequate solder tools applicable for lead-free solder alloy. The solder tool must be able o To reach at least a solder-temperature of 400C, o To stabilize the adjusted temperature at the solder-tip o To exchange solder-tips for different applications. Adju
21、st your solder tool so that a temperature around 360C 380C is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400C otherwise wear-out of tips will rise drastically and flux-fluid will be destroyed. To avoid wear-out of ti
22、ps switch off un-used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid, clean carefully the solder-joint from old solder alloy an
23、d re-solder with new solder alloy (SAC305). Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs: - always use the 12nc-recognizable soldering temperature profile of the spec
24、ific BGA (for de-soldering always use highest lead-free temperature profile, in case of doubt) - lead free BGA-ICs will be delivered in so-called dry-packaging (sealed pack including a silica gel pack) to protect the IC against moisture. After opening, dependent of MSL-level seen on indicator-label
25、in the bag, the BGA-IC possibly still has to be baked dry. This will be communicated via AYS-website. Do not re-use BGAs at all. For sets produced before 1.1.2005, containing leaded soldering-tin and components, all needed spare-parts will be available till the end of the service-period. For repair
26、of such sets nothing changes. On our website: www.atyourservice.ce.P You find more information to: BGA-de-/soldering (+ baking instructions) Heating-profiles of BGAs and other ICs used in Philips-sets You will find this and more technical information within the “magazine”, chapter “workshop news”. For additional questions please contact your local repair-helpdesk. Notes 1-72 ES 2-1 Register your product and get support at ( ) HDMI COAXIAL COAXIAL A A 1 2-2
免费区 
