Philips-DVDR-7300-H-Service-Manual电路原理图.pdf

《Philips-DVDR-7300-H-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-DVDR-7300-H-Service-Manual电路原理图.pdf（194页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by KC-TE 0636 AV Systems Printed in the Netherlands Subject to modication EN 3139 785 31532DVDR5350H/02/05/19HDD & DVD RecorderCLASS 1LASER PRODUCTContents Page1 Technical Specications and ConnectionFacilities 22 Safety Information, General Notes & Lead Free Requirements 53 Directions for

2、Use 74 Mechanical Instructions 105 Firmware Upgrading & Diagnostic Software 146 Block Diagrams,Waveforms, Wiring Diagram 117Overall block diagram 117Wiring diagram 118Waveforms of Analog Board 119Waveforms of Digital Board 120Waveforms of Front Board 121Waveforms of HDMI Board 121Test Points Overvie

3、w for Analog Board 122Test Points Overview for Display/Front Connector Board 123Test Points Overview for Digital Board 124Test Points Overview for HDMI Board 125Contents Page7 Circuit Diagrams and PWB Layout 126Analog Circuit Diagrams 126Analog Layout Diagrams 136Front Display/Connector Circuit Diag

4、rams 138Front Display/Connector Layout Diagrams 140Front Standby Circuit & Layout Diagrams 141Front Tray LED Left/Right Circuit & Layout Diagrams 142Digital Circuit Diagrams 143Digital Layout Diagrams 154HDMI Circuit Diagrams 156HDMI Layout Diagrams 1608 Alignments & Test Procedures 1639 Circuit and

5、 IC description 164Circuit Description 164IC Description 17210 Exploded view & Service parts list 188Exploded view 188Service parts list 19211 Revision list 194 Copyright 2005 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.All rights reserved. No part of this publication may be reprodu

6、ced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.Version 1.2DVDR7310H/75/97 & DVDR7300H/02/05/19/75/97EN 2 3139 785 315321. Technical Specifi cations and Connection Facilities1. T

7、echnical Specifi cations and Connection Facilities1.1 PCB Locations1.2 Diversity MatrixDVDR5350H DVDR7300H DVDR7310HHDD capacity 160GB 250GB 250GBHDMI x x1.3 Read / Write SpeedType of Disc (Function) Disc Rotation SpeedRead Speed CD 7X CAV Read Speed DVD 4X CAV Write Speed DVD+R/+RW 2.4X ZCAVWrite S

8、peed DVD-R/-RW 2X 1.4 General:Mains voltage : 220V 240V Mains frequency : 50 HzPower consumption (record) : 40 WStandby Power Consumption : 4.5V / 9.5V / 1V / 10kVideo - CinchInput voltage : 1Vpp 3dB Input impedance : 75Video - YC (Hosiden)According to IEC 933-5Superimposed DC-level on pin 4 (load 1

9、00k)3.5V is detected as 16:9 aspect ratioInput voltage Y : 1Vpp 3dB Input impedance Y : 75Input voltage C : 300mVpp 3dBInput impedance C : 751.6.4 Out 1Component Video Cinch Y/Pb/Praccording EIO-770-I-A, EIA-770-2Audio - CinchOutput voltage : 2Vrms max.Output impedance : 10k1.6.5 Out 2Audio - CinchO

10、utput voltage : 2Vrms max.Output impedance : 10kVideo - CinchOutput voltage : 1Vpp 3dB Output impedance : 75Video - YC (Hosiden)According to IEC 933-5Superimposed DC-level on pin 4 (load 100k)3.5V is detected as 16:9 aspect ratioOutput voltage Y : 1Vpp 3dB Input impedance : 75Output voltage C : 300m

11、Vpp 3dBInput impedance : 751.7 Digital Inputs / Outputs 1.7.1 Digital OutputDigital Audio Coaxial / OpticalLCM : according IEC 60958MPEG 1, MPEG 2, AC3 : according IEC 61937DTS : according IEC 61937 + addendum1.7.2 HDMI OutputType A connector (19 pins)1.7.3 Digital Video Input (IEEE 1394)Implementat

12、ion Standard according:IEEE Std 1394-1995 IEC61883 - Part1IEC61883 - Part 2 SD-DVCR (02-01-1997)Specifi cation of consumer use digital VCRs using 6.3mm magnetic tape dec.1994Mechanical connection according to Annex of IEC 61883-1EN 4 3139 785 315321. Technical Specifi cations and Connection Faciliti

13、es1.7.4 G-Link (for IR-remote transmitting device)Output voltage : 5 0.5V (high level)0.4 0.3V (low level)Output impedance : 1501.8 Video PerformanceAll outputs loaded with 75SNR measurements over full bandwidth without weighting.1.8.1 SCART (RGB)SNR : 55dB on all outputBandwidth : 4.8MHz -3dB1.9 Au

14、dio Performance 1.9.1 Cinch Output RearOutput voltage 2 channel mode : 2Vrms 2dBChannel unbalance (1kHz) : 100dBCrosstalk 16Hz-20kHz : 87dBFrequency response 20Hz-20kHz : 0.5dBSignal to noise ratio (unweighted) : 85dBDynamic range 1kHz : 83dBDistortion and noise 1kHz : 83dBDistortion and noise 16Hz-

15、20kHz : 75dBIntermodulation distortion : 70dBMute : 95dB1.9.2 Scart AudioOutput voltage 2 channel mode : 1.6Vrms 2dBChannel unbalance (1kHz) : 85dBCrosstalk 16Hz-20kHz : 70dBFrequency response 20Hz-20kHz : 0.5dBSignal to noise ratio (unweighted) : 80dBDynamic range 1kHz : 75dBDistortion and noise 1k

16、Hz : 75dBDistortion and noise 16Hz-20kHz : 50dBIntermodulation distortion : 70dBMute : 80dB1.10 Dimensions and WeightHeight of feet : 5.5mmApparatus tray closed : WxDxH:435x335x76mmApparatus tray open : WxDxH:435x472x76mmWeight without packaging : 5kgWeight with packaging : 8kg1.11 Laser Output Powe

17、r & Wavelength1.11.1 DVDOutput power during reading : 0.8mWOutput power during writing : 20mWWavelength : 650nm1.11.2 CDOutput power : 0.3mWWavelength : 780nmEN 53139 785 31532 2.Safety Information, General Notes & Lead Free Requirements2.1 Safety Instructions2.1.1 General SafetySafety regulations r

18、equire that during a repair: Connect the unit to the mains via an isolation transformer. Replace safety components, indicated by the symbol ,only by components identical to the original ones. Anyother component substitution (other than original type) may increase risk of fi re or electrical shock ha

19、zard.Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention tothe following points: Route the wires/cables correctly, and fi x them with themounted cable clamps. Check the insulation of the mains lead for externaldamage. Chec

20、k the electrical DC resistance between the mains plug and the secondary side:1. Unplug the mains cord, and connect a wire betweenthe two pins of the mains plug.2. Set the mains switch to the on position (keep themains cord unplugged!).3. Measure the resistance value between the mains plug and the fr

21、ont panel, controls, and chassis bottom.4. Repair or correct unit when the resistancemeasurement is less than 1 M.5. Verify this, before you return the unit to the customer/user (ref. UL-standard no. 1492).6. Switch the unit off, and remove the wire between the two pins of the mains plug.2.1.2 Laser

22、 SafetyThis unit employs a laser. Only qualifi ed service personnel may remove the cover, or attempt to service this device (due to possible eye injury).Laser Device UnitType : Semiconductor laser GaAlAsWavelength : 650 nm (DVD): 780 nm (VCD/CD)Output Power : 20 mW(DVD+RW writing): 0.8 mW(DVD readin

23、g): 0.3 mW(VCD/CD reading)Beam divergence : 60 degreeCLASS 1LASER PRODUCTFigure 2-1Note: Use of controls or adjustments or performance of procedure other than those specifi ed herein, may result in hazardous radiation exposure. Avoid direct exposure to beam.2.2 Warnings2.2.1 General All ICs and many

24、 other semiconductors are susceptible to electrostatic discharges (ESD, ). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential

25、.Available ESD protection equipment: Complete kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. Wristband tester 4822 344 13999. Be careful during measurements in the live voltage section. The primary side of the power supply, including the heatsin

26、k, carries live mains voltage when you connect the player to the mains (even when the player is off!). It is possible to touch copper tracks and/ or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or compo

27、nents in this area. A lightning stroke and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply. Never replace modules, or components, while the unit is on.2.2.2 Laser The use of optical instruments with this product, will increase eye hazard. Only qual

28、ifi ed service personnel may remove the cover or attempt to service this device, due to possible eye injury. Repair handling should take place as much as possible with a disc loaded inside the player. Text below is placed inside the unit, on the laser cover shield:Figure 2-22. Safety Information, Ge

29、neral Notes & Lead Free RequirementsCAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAMADVARSEL SYNLIG OG USYNLIG LASERSTRLING VED BNING UNDG UDSTTELSE FOR STRLINGADVARSEL SYNLIG OG USYNLIG LASERSTRLING NR DEKSEL PNES UNNG EKSPONERING FOR STRLENVARNING SYNLIG OCH OSYNLIG L

30、ASERSTRLNING NR DENNA DEL R PPNAD BETRAKTA EJ STRLENVARO! AVATTAESSA OLET ALTTIINA NKYVLLE JA NKYMTTMLLE LASER STEILYLLE. L KATSO STEESEENVORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEFFNET NICHT DEM STRAHL AUSSETSEN DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID D

31、IRECT EXPOSURE TO BEAMATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS DOUVERTURE EXPOSITION DANGEREUSE AU FAISCEAUEN 6 3139 785 315322. Safety Information, General Notes & Lead Free Requirements2.3 Lead Free RequirementInformation about Lead-free produced setsPhilips CE is starting productio

32、n of lead-free sets from 1.1.2005 onwards. INDENTIFICATION:Regardless of special logo (not always indicated) One must treat all sets from 1 Jan 2005 onwards, according next rules. Example S/N:Bottom line of typeplate gives a 14-digit S/N. Digit 5&6 is the year, digit 7&8 is the week number, so in th

33、is case 1991 wk 18So from 0501 onwards = from 1 Jan 2005 onwardsImportant note: In fact also products of year 2004 must be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this.Due to lead-free techn

34、ology some rules have to be respected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-pate is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops should

35、 be avoided because paste is not easy to store and to handle. Use only adequate solder tools applicable for lead-free solder alloy. The solder tool must be able o To reach at least a solder-temperature of 400C, o To stabilize the adjusted temperature at the solder-tip o To exchange solder-tips for d

36、ifferent applications. Adjust your solder tool so that a temperature around 360C 380C is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400C otherwise wear-out of tips will rise drastically and fl ux-fl uid will be destr

37、oyed. To avoid wear-out of tips switch off un-used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid or does not know whether prod

38、uct is lead-free, clean carefully the solder-joint from old solder alloy and re-solder with new solder alloy (SAC305). Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs:-

39、always use the 12nc-recognizable soldering temperature profi le of the specifi c BGA (for de-soldering always use the lead-free temperature profi le, in case of doubt) - lead free BGA-ICs will be delivered in so-called dry-packaging (sealed pack including a silica gel pack) to protect the IC against

40、 moisture. After opening, dependent of MSL-level seen on indicator-label in the bag, the BGA-IC possibly still has to be baked dry. (MSL=Moisture Sensitivity Level). This will be communicated via AYS-website.Do not re-use BGAs at all. For sets produced before 1.1.2005 (except products of 2004), cont

41、aining leaded solder-alloy and components, all needed spare-parts will be available till the end of the service-period. For repair of such sets nothing changes. On our website www.atyourservice.ce.P you fi nd more information to: null BGA-de-/soldering (+ baking instructions)null Heating-profi les o

42、f BGAs and other ICs used in Philips-setsYou will fi nd this and more technical information within the “magazine”, chapter “workshop news”.For additional questions please contact your local repair-helpdesk.EN 73139 785 315323. Directions For UseThe following except of the Quick Use Guide serves as a

43、n introduction to the set.The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center: Quick Start GuideDVDR 5350H DVDR 7300HHDD & DVD Player / RecorderRF coaxial cableScart cableG-LINK cable & transmitterPower cableQuick start g

44、uideRemote controland 2 batteriesUser manualDVD recorder/hard diskWhats in the Box3.Directions For UseFrom an off-air antennaor cableboxTelevision (rear)Philips Recorder (rear)Basic connection Before connectingUnplug the antenna cable that is currently connected to your TV.Connecting1Disconnect the

45、antenna cable from your TV and connect it to the ANTENNA socket on this recorder.2Use the supplied RF coaxial cable to connect the TV socket on this recorder to the Antenna In socket on your TV.3Use the supplied scart cable to connect the EXT1 TO TV-I/O Scart socket on this recorder to the SCART IN

46、socket on your TV.Note See the accompanying user manual for others possible connection (e.g.HDMI,Component Video).4Connect the power cable from the recorder to an AC power outlet.Start with the Basic connection.If you have a VCR,follow the instructions for Connection with VCR or similar device.If yo

47、u have a set-top box,follow the instructions for Connection with set-top box.EN 8 3139 785 315323. Directions For UseSetup External Receiver 1 Has the External Receiver 1 changed to Programme Number 101?Television (rear)VCR or similardevice (rear)Positioningof G-LINK transmitterset-topboxG-LINK tran

48、smitterTelevision (rear)TosourceSe (GUIDE(rear)ppFrom an off-air antenna or cable boxConnection with VCRor similar deviceBefore connectingYour new Philips Recorder replaces the VCR for your recording needs.First,unplug all the connections from your VCR.Connecting1Follow step 1 to 4 of Basic connection to connect this recorder before you proceed to step 2 below.2Use another scart cable (not supplied) to connect the EXT2 AUX-I/O Scart socket on this recorder to the SCART OUT socket on your VCR.3Connect the power cable from the VCR to an AC power outlet.Note In this s