Philips-DVP-3388-Service-Manual电路原理图.pdf

《Philips-DVP-3388-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-DVP-3388-Service-Manual电路原理图.pdf（42页珍藏版）》请在收音机爱好者资料库上搜索。

1、TABLE OF CONTENTS Page Version 1.0 Service Manual . Technical Specifications.1-2 . Safety Instruction, Warning 525 (NTSC/60Hz) Playback: Multi-standard (PAL/NTSC) Video performance Video DAC: 12 bits, 108 MHz Y Pb Pr: 0.7 Vpp 75 ohm Video output: 1 Vpp 75 ohm Video format Digital compression: MPEG 2

2、: DVD/SVCD MPEG 1: VCD/DivX Horizontal resolution: DVD: 720/1920 pixels (50 Hz); 720/1920 pixels (60 Hz) VCD: 352 pixels (50 Hz); 352 pixels (60 Hz) Vertical resolution: DVD: 576/1080 lines (50 Hz); 480/1080 lines (60 Hz) VCD: 288 lines (50 Hz); 240 lines (60 Hz) Audio performance DA converter: 24 b

3、its, 192 kHz Frequency response: DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz - 44 kHz (96 kHz) SVCD: 4 Hz - 20 kHz (44.1 kHz); 4 Hz - 22 kHz (48 kHz) CD/VCD: 4 Hz - 20 kHz (44.1 kHz) Signal-Noise (1 kHz): 90 dB (A-weighted) Dynamic range (1 kHz): 85 dB (A-weighted) Crosstalk (1 kHz): 85 dB Distortion/noise (1

4、 kHz): 70 dB MPEG MP3: MPEG Audio L3 Audio format Digital: MPEG/AC-3/PCM: Compressed digital (16, 20, 24 bits fs, 44.1, 48, 96 kHz) MP3 (ISO 9660): 96, 112, 128, 256 kbps IEC61937 for MPEG 1/2, Dolby Digital 1 optical HDMI output 5.1 channel analog output Audio Front L+R: Cinch (white/red) Audio Rea

5、r L+R: Cinch (white/red) Audio Center: Cinch (blue) Audio Subwoofer: Cinch (black) Main unit Main unit Dimensions (w x h x d): 360 x 37 x 209 (mm) Net Weight: approximately 1.3 kg Power Power supply rating: 110 V - 240 V; 50/60 Hz Power consumption: 12 W Power consumption in standby mode: 0.3 W Lase

6、r Speci cation Type: Semiconductor laser InGaAIP (DVD), AIGaAs (CD) Wave length: 658 nm (DVD), 790 nm (CD) Output Power: 7.0 mW (DVD), 10.0 mW (VCD/CD) Beam divergence: 60 degrees 1-2Safety instruction 1. General safety Safety regulations require that during a repair: . Connect the unit to the mains

7、 via an isolation transformer. . Replace safety components indicated by the symbol , only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard. Safety regulations require that after a repair, yo

8、u must return the unit in its original condition. Pay, in particular, attention to the following points: . Route the wires/cables correctly, and fix them with the mounted cable clamps. . Check the insulation of the mains lead for external damage. . Check the electrical DC resistance between the main

9、s plug and the secondary side: 1) Unplug the mains cord, and connect a wire between the two pins of the mains plug. 2) Set the mains switch the “on” position (keep the mains cord unplug). 3) Measure the resistance value between the mains plug and the front panel, controls, and chassis bottom. 4) Rep

10、air or correct unit when the resistance measurement is less than 1M . 5) Verify this, before you return the unit to the customer/user (ref. UL-standard no. 1492). 6) Switch the unit “off”, and remove the wire between the two pins of the mains plug. 2.Laser safety This unit employs a laser. Only qual

11、ified service personnel may remove the cover, or attempt to service this device (due to possible eye injury). Laser device unit T ype : Semiconductor laser GaAlAs Wavelength : 650nm (DVD) : 780nm (VCD/CD) Output power : 7mW (DVD) : 10mW (DVD /CD) Beam divergence: 60 degree Note: Use of controls or a

12、djustments or performance of procedure other than those specified herein, may result in hazardous radiation exposure. Avoid direct exposure to beam. Safety instruction, Warning & Notes 1-3Warning 1.General . All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD). Car

13、eless handing during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: 1) Complete kit ESD3 (small tablemat, wri

14、stband, connection box, extension cable and earth cable) 4822 310 10671. 2) Wristband tester 4822 344 13999. . Be careful during measurements in the live voltage section. The primary side of the power supply , including the heat sink, carries live mains voltage when you connect the player to the mai

15、ns (even when the player is “off”!). It is possible to touch copper tracks and/or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A “lighting stroke” and a stripe-marked printin

16、g on the printed wiring board, indicate the primary side of the power supply. . Never replace modules, or components, while the unit is “on”. 2. Laser . The use of optical instruments with this product, will increase eye hazard. . Only qualified service personnel may remove the cover or attempt to s

17、ervice this device, due to possible eye injury. . Repair handing should take place as much as possible with a disc loaded inside the player. . Text below is placed inside the unit, on the laser cover shield: Notes: Manufactured under licence from Dolby Laboratories. The double-D symbol is trademarks

18、 of Dolby Laboratories, Inc. All rights reserved. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN, AVOID EXPOSURE TO BEAM. 1-4Lead-Free requirement for service INDENTIFICATION: Regardless of special logo (not always indicated) One must treat all sets from 1.1.2005 onwards, according next ru

19、les. Important note: In fact also products a little older can also be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this. Due to lead-free technology some rules have to be respected by the worksho

20、p during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops should be avoided because paste is not easy to store and

21、to handle. Use only adequate solder tools applicable for lead-free solder alloy. The solder tool must be able o To reach at least a solder-temperature of 400C, o To stabilize the adjusted temperature at the solder-tip o To exchange solder-tips for different applications. Adjust your solder tool so t

22、hat a temperature around 360C 380C is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400C otherwise wear-out of tips will rise drastically and flux-fluid will be destroyed. To avoid wear-out of tips switch off un-used eq

23、uipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid, clean carefully the solder-joint from old solder alloy and re-solder with new sol

24、der alloy (SAC305). Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs: - always use the 12nc-recognizable soldering temperature profile of the specific BGA (for de-solderi

25、ng always use highest lead-free temperature profile, in case of doubt) - lead free BGA-ICs will be delivered in so-called dry-packaging (sealed pack including a silica gel pack) to protect the IC against moisture. After opening, dependent of MSL-level seen on indicator-label in the bag, the BGA-IC p

26、ossibly still has to be baked dry. This will be communicated via AYS-website. Do not re-use BGAs at all. For sets produced before 1.1.2005, containing leaded soldering-tin and components, all needed spare-parts will be available till the end of the service-period. For repair of such sets nothing cha

27、nges. On our website: www.atyourservice.ce.P You find more information to: BGA-de-/soldering (+ baking instructions) Heating-profiles of BGAs and other ICs used in Philips-sets You will find this and more technical information within the “magazine”, chapter “workshop news”. For additional questions

28、please contact your local repair-helpdesk. Notes 1-52009 Koninklijke Philips N.V. All rights reserved. 12 NC 8670 000 48879 sgptt_908/94 Register your product and get support at DVP3388 Off On Audio Sync Volume Digital Audio Analog Output HDMI Audio Audio Setup Sound Mode Speaker Setup CD Upsamplin

29、g 3 / The following excerpt of the Quick Start Guide serves as an introduction to the set. The complete Direction For Use can be download in different languages from Philips Customer Contact & Support site: 2-11 General Setup English Auto Standby DivX(R) VOD Code OSD Language Disc Lock Sleep Timer

30、Auto (Eng) 2 HDMI IN HDMI OUT AUDIO OUT FRONT L/R & TV OUT COMPONENT VIDEO IN Pb Y Pr YPbPr & AUDIO OUT FRONT L/R 2-2Product overview Main unit a2 (Standby-on) Turn on the DVD player or switch to standby mode. b Disc compartment c Display panel d Z (Open/Close) Open or close the disc compartment. e

31、u (Play/Pause) Start, pause or resume disc play. f (USB) jack Connect a USB ash drive. 4 3 1 2 6 5 Remote control 4 3 6 7 9 8 1 5 2 16 17 12 15 13 14 10 11 18 a2 (Standby-On) Turn on the DVD player or switch to standby mode. b Z (Open/Close) Open or close the disc compartment. c DISC MENU Access or

32、exit the disc menu. Switch to disc mode. For VCD/SVCD, turn PBC (Playback Control) on or off in PBC mode. 2-3d v V b B (Navigation buttons) Navigate through the menus. Search fast-forward ( B) or fast- backward (b). Press repeatedly to change the search speed. Search slow-forward ( v) or slow- backw

33、ard (V). Press repeatedly to change the search speed. e BACK Return to the previous display menu. For DVD, navigate to the title menu. For VCD version 2.0 or SVCD with PBC turned on, return to the menu. f / (Previous/Next) Skip to the previous or next title, chapter, or track. Press and hold for fas

34、t-backward or fast-forward search. g (USB) Switch to USB mode and display the content. h Numeric buttons Select an item to play. i SUBTITLE Select DVD or DivX subtitle language. Access the menu to USB copy or USB delete. j, ZOOM Fit the picture format to the TV screen. Zoom in or out of the picture.

35、 k VOLUME Display the current volume level and use (b) or (B) navigation buttons to set the volume level between 0 20. l REPEAT/REPEAT A-B Toggle between various repeat modes. Mark the section for repeat play, or turn off repeat mode. m AUDIO/CREATE MP3 Select an audio language/channel. Access the m

36、enu to create MP3. n x (Stop) Stop disc play. o u (Play/Pause) Start, pause or resume disc play. p INFO For disc, display the current status or disc information. For slideshows, display a thumbnail view of photo les. q OK Con rm an entry or selection. r SETUP Access or exit the setup menu. 2-4Mechan

37、ical and Dismantling Instructions Dismantling Instruction The following guidelines show how to dismantle the player. Step1: Remove 5 screws around the Top Cover, and then remove the Top Cover (Figure 1). Figure 1 Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be

38、removed first. (Figure 2) Note: Make sure to operate gently otherwise the guider would be damaged. Figure 2 3-1 Please kindly note that dismantle the front door assembly carefully to avoid damage tray and the front door. Detailed information please refer to the model set.Mechanical and Dismantling I

39、nstructions Dismantling Instruction Step3: If the tray cant open in normal way, you can make it through the instruction as below (Figure 3). Note: Make sure to operate gently otherwise the guider would be damaged. Figure 3 Step4: Dismantling Front Panel, disconnect the connectors (XP2, XP6. XP7), need release 4 snaps of Front Panel and 2 snaps of bottom cabinet , then gently pull the Panel out from the set. (Figure 4 - Figure 6) Figure 4 3-2 Detailed information please refer to the model set. XP5 XP4 XP3 XP2 XP1 XP7 XP6