Philips-HTS-3511-E-Service-Manual电路原理图.pdf

《Philips-HTS-3511-E-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-HTS-3511-E-Service-Manual电路原理图.pdf（47页珍藏版）》请在收音机爱好者资料库上搜索。

1、TABLE OF CONTENTS Page Service Manual . Mechanical and Dismantling Instructions.3-1 . Software Upgrades and Region Code Change.4-1 . Trouble Shooting Chart.5-1 . Wiring Diagram.6-1 . Electrical Diagrams and Print-layouts.7-1 . Set Mechanical Exploded view & Part list.8-1 Copyright 2010 Philips Consu

2、mer Electronics B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. CLASS 1 LASER PRODU

3、CT PHILIPS GB HTS3511E/94 . DFU Instruction.2-1 . Revision List.9-1 Home Theater DVD Player . Technical Specifications.1-3 . Safety Instruction, Warning & Notes.1-4 Published by RY - 1039 BU AVM Printed in The Netherlands Subject to modification Version 1.1 3139 785 35431 . Location of PCB Bds,Versi

4、on Variation and Repair Scenario Matrix.1-2LOCATION OF PCB BOARDS ： Version Variation ： Type/Versions Features HTS3511E/94 Output Power-300W X Voltage(110240v) X Repair Scenario Matrix ： Type/Versions Board in used HTS3511E/94 Main Board C Front Control Board C Amplifier Board C Power Board C *Bd:Bo

5、ard Level Replacement *C:Component Level Repair 1-2 VideoSignal system: PAL / NTSC HDMI output: 480i/576i, 480p/576p, 720p, 1080i, 1080pAudioSampling frequency: MP3: 32 kHz, 44.1 kHz, 48 kHz WMA: 44.1 kHz, 48 kHz Constant bit rate: MP3: 112 kbps - 320 kbps WMA: 48 kbps - 192 kbps RadioTuning range:

6、FM 87.5-108 MHz (50/100 kHz)Signal-to-noise ratio: FM 50 dB Frequency response: FM 180 Hz 10 kHz / 6dBUSBCompatibility: Hi-Speed USB (2.0) Class support: UMS (USB Mass Storage Class)File system: FAT12, FAT16, FAT32 Maximum memory support: 65 dB (CCIR) / (A-weighted)Input sensitivity: AUX: 1 mV Count

7、ry DVD Europe, United Kingdom Latin America Australia, New Zealand Russia, India China Asia Pacific, Taiwan, Korea 1-3 Speakers System: full range satellite Speaker impedance: 8 ohm (center), 4 ohm (Front/Rear)Speaker drivers: 3” full range Frequency response: 150 Hz-20 kHz Dimensions (WxHxD): HTS35

8、10: 96 x 162 x 96 (mm) HTS3520: Center: 160.9 x 95 x 92 (mm)Front/Rear: 95 x 160.9 x 87 (mm)Weight: HTS3510: 0.68 kg HTS3520: Center: 0.77 kgFront/Rear: 0.56 kg/eachCable length: Center: 3 m Front: 4 m Rear: 10 m Laser speci cationType: Semiconductor laser GaAIAs (CD) Wave length: 645 - 665 nm (DVD)

9、, 770 - 800 nm (CD)Output power: 6 mW (DVD), 7 mW (VCD/CD)Beam divergence: 60 degrees. 1-4Safety instruction 1. General safety Safety regulations require that during a repair: . Connect the unit to the mains via an isolation transformer. . Replace safety components indicated by the symbol , only by

10、components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard. Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention to the follow

11、ing points: . Route the wires/cables correctly, and fix them with the mounted cable clamps. . Check the insulation of the mains lead for external damage. . Check the electrical DC resistance between the mains plug and the secondary side: 1) Unplug the mains cord, and connect a wire between the two p

12、ins of the mains plug. 2) Set the mains switch the “on” position (keep the mains cord unplug). 3) Measure the resistance value between the mains plug and the front panel, controls, and chassis bottom. 4) Repair or correct unit when the resistance measurement is less than 1M . 5) Verify this, before

13、you return the unit to the customer/user (ref. UL-standard no. 1492). 6) Switch the unit “off”, and remove the wire between the two pins of the mains plug. 2.Laser safety This unit employs a laser. Only qualified service personnel may remove the cover, or attempt to service this device (due to possi

14、ble eye injury). Laser device unit T ype : Semiconductor laser GaAlAs Wavelength : 650nm (DVD) : 780nm (VCD/CD) Output power : 7mW (DVD) : 10mW (DVD /CD) Beam divergence: 60 degree Note: Use of controls or adjustments or performance of procedure other than those specified herein, may result in hazar

15、dous radiation exposure. Avoid direct exposure to beam. Safety instruction, Warning & Notes 1-5Warning 1.General . All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD). Careless handing during repair can reduce life drastically. Make sure that, during repair, you a

16、re at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: 1) Complete kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. 2) Wristband tester

17、4822 344 13999. . Be careful during measurements in the live voltage section. The primary side of the power supply , including the heat sink, carries live mains voltage when you connect the player to the mains (even when the player is “off”!). It is possible to touch copper tracks and/or components

18、in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A “lighting stroke” and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply. . Never replace

19、 modules, or components, while the unit is “on”. 2. Laser . The use of optical instruments with this product, will increase eye hazard. . Only qualified service personnel may remove the cover or attempt to service this device, due to possible eye injury. . Repair handing should take place as much as

20、 possible with a disc loaded inside the player. . Text below is placed inside the unit, on the laser cover shield: Notes: Manufactured under licence from Dolby Laboratories. The double-D symbol is trademarks of Dolby Laboratories, Inc. All rights reserved. CAUTION: VISIBLE AND INVISIBLE LASER RADIAT

21、ION WHEN OPEN, AVOID EXPOSURE TO BEAM. 1-6 1-7Lead-Free requirement for service INDENTIFICATION: Regardless of special logo (not always indicated) One must treat all sets from 1.1.2005 onwards, according next rules. Important note: In fact also products a little older can also be treated in this way

22、 as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this. Due to lead-free technology some rules have to be respected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 14

23、9 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops should be avoided because paste is not easy to store and to handle. Use only adequate solder tools applicable for lead-free solder alloy. The sold

24、er tool must be able o To reach at least a solder-temperature of 400C, o To stabilize the adjusted temperature at the solder-tip o To exchange solder-tips for different applications. Adjust your solder tool so that a temperature around 360C 380C is reached and stabilized at the solder joint. Heating

25、-time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400C otherwise wear-out of tips will rise drastically and flux-fluid will be destroyed. To avoid wear-out of tips switch off un-used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy /

26、 parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid, clean carefully the solder-joint from old solder alloy and re-solder with new solder alloy (SAC305). Use only original spare-parts listed in the Service-Manuals. Not list

27、ed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs: - always use the 12nc-recognizable soldering temperature profile of the specific BGA (for de-soldering always use highest lead-free temperature profile, in case of doubt) - lead free BGA-IC

28、s will be delivered in so-called dry-packaging (sealed pack including a silica gel pack) to protect the IC against moisture. After opening, dependent of MSL-level seen on indicator-label in the bag, the BGA-IC possibly still has to be baked dry. This will be communicated via AYS-website. Do not re-u

29、se BGAs at all. For sets produced before 1.1.2005, containing leaded soldering-tin and components, all needed spare-parts will be available till the end of the service-period. For repair of such sets nothing changes. On our website: www.atyourservice.ce.P You find more information to: BGA-de-/solder

30、ing (+ baking instructions) Heating-profiles of BGAs and other ICs used in Philips-sets You will find this and more technical information within the “magazine”, chapter “workshop news”. For additional questions please contact your local repair-helpdesk. Notes 1-8User Manual Audio/Video FM HDMI * Ada

31、ptador fornecido como acessrio no dever ser usado nas redes eltricas do Brasil, seu uso destinado exclusivamente a outros pases da Amrica Latina. The following excerpt of the Quick Start Guide serves as an introduction to the set. The complete Direction For Use can be download in different languages

32、 from Philips Customer Contact & Support site: 2-1 QSG for HTS3511E/94: HDMI Cable and Power socket transition only for /55.1 1 2-2SUBWOOFER REAR LEFT REAR RIGHT FRONT RIGHT FRONT LEFT FRONT CENTER 2 3 FM Cable 2-35 1 6 4 AAA x 2 2 HDMI Cable Audio Cable 2-42 USB Settings TV HDMI 1 HOME THEATER HOM

33、E THEATER General Setup Screen Saver Sleep Timer Display Dim Disc Lock OSD Language DivX(R) VOD Code General Setup OSD Language 2 5 3 6 2-53 1 2 3 4 3 1 2 2-6Speci cations are subject to change without notice Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective own

34、ers 2010 Koninklijke Philips Electronics N.V. All rights reserved. sgythy_1001/55/v1 User Manual 1 2 3 2-7 Y our home theaterCongratulations on your purchase, and welcome to Philips! T o fully bene t from the support that Philips offers, register your home theater at www. unita Disc compartment b

35、( Open/Close )Opens or closes the disc compartment.c ( Play/Pause )Starts, pauses or resumes play.d ( Stop )Stops play. In radio mode, erases the current preset radio station.e ( Standby-On )Switches the home theater on or to standby. f SOURCE Selects an audio/video source for the home theater.g / Skips to the previous or next track, chapter or le.In radio mode, selects a preset radio station.h Display panel i Volume control wheel 2-8 HTS3511E/94: