Philips-HTS-3172-Service-Manual电路原理图.pdf

《Philips-HTS-3172-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-HTS-3172-Service-Manual电路原理图.pdf（53页珍藏版）》请在收音机爱好者资料库上搜索。

1、 DVD Home Theater System Service HTS3172/98/93Service ManualTABLE OF CONTENTSChapter Copyright 2009 Philips Consumer Electroni cs B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any mea

2、ns, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by LM0909 Service Audio Printed in The Netherlands Subject to modification Version 1.0 GB 3139 785 3482 0 LASER BEAM SAFETY PRECAUTIONS.1-2 STANDARD NOTES FOR SERVICING. .1-3 SAFETY AND IMPORTAN

3、T NOTICE.1-7 LOCATION OF PCB BOARDSVERSION VARIATION .2-1 REMOTE CONTROL.2-2 OPERATING CONTROLS AND FUNCTIONS .2-3 SPECIFICATIONS .3-1 MEASUREMENT SETUP. 3-2 .SYSTEM,REGION CODE,ETC.SETTING PRODURE. .3-3 RETURN UNIT TEST FLOW.3-4 MAIN UNIT REPAIR CHART.3-5 DISASSEMBLY INSTRUCTIONS .4 BLOCK WIRING DI

4、AGRAM.5 AMPLIFIER BOARD LED + KEY BOARD DECODE BOARD POWER BOARD.6 MECHANICAL EXPLODE VIEWPART LIST.11 PACKAGING EXPLODED VIEW.10 .REVISION LIST.12 LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or al

5、low it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser beam. CAUTION: Use of controls and adj

6、ustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure. CAUTION LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM. Location: Top of DVD mechanism. 1 - 2STANDARD NOTES FOR SERVICING Instructions for Connectors 1. When you connect or disconnect the

7、FFC (Flexible Foil Connector) cable, be sure to first disconnect the AC cord. 2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle. Pb (Lead) Free Solder When soldering, be sure to use the Pb free solder. IDENTIFICATION: Regardless of special logo (n

8、ot always indicated)One must treat all sets from 1.1.2005 onwards, according next rules. Important note: In fact also products a little older can also be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong

9、 to this. Due to lead-free technology some rules have to be respected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder paste is required, please contact the manufacturer of your solder-equipment. In general use of sol

10、der paste within workshops should be avoided because paste is not easy to store and to handle. Use only adequate solder tools applicable for leadfree solder alloy. The solder tool must be able To reach at least a solder-temperature of 400C, To stabilize the adjusted temperature at the solder-tip To

11、exchange solder-tips for different applications. Adjust your solder tool so that a temperature around 360C - 380C is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400C otherwise wear-out of tips will rise drastically an

12、d flux-fluid will be destroyed. To avoid wear-out of tips switch off un-used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid, cl

13、ean carefully the solder-joint from old solder alloy and re-solder with new solder alloy (SAC305). Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs:- always use the 12nc-

14、recognizable soldering temperature profile of the specific BGA (for desoldering always use highest lead-free 1 - 3temperature profile, in case of doubt) - lead free BGA-ICs will be delivered in so-called dry-packaging (sealed pack including a silica gel pack) to protect the IC against moisture. Afte

15、r opening, dependent of MSL-level seen on indicatorlabel in the bag, the BGA-IC possibly still has to be baked dry. This will be communicated via AYS-website. Do not re-use BGAs at all. For sets produced before 1.1.2005, containing leaded soldering-tin and components, all needed spare-parts will be

16、available till the end of the service-period. For repair of such sets nothing changes. On our website www.atyourservice.ce.P you find more information to: BGA-de-/soldering (+ baking instructions) Heating-profiles of BGAs and other ICs used in Philips-sets. You will find this and more technical info

17、rmation within the “magazine”, chapter “workshop news”. For additional questions please contact your local repair-helpdesk. How to Remove / Install Flat Pack-IC 1. Removal With Hot-Air Flat Pack-IC Desoldering Machine: 1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to th

18、e Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1) 2. Remove the flat pack-IC with tweezers while applying the hot air. 3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (

19、glue will be melted). (Fig. S-1-6) 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) CAUTION: 1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. 2. Do not supply hot air to the

20、 chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2) 3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin

21、or the solder lands under the IC when removing it. With Soldering Iron: 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 2. Lift each lead of the flat pac

22、k-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4) 1 - 43. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, firs

23、t apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) With Iron Wire: 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder

24、 flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to

25、lift the IC leads from the CBA contact pads as shown in Fig.S-1-5. 4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 5. Release the flat

26、 pack-IC from the CBA using tweezers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied. 2. Installation 1. Using

27、desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2. The “ ” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation

28、. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.) 3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges. 1 - 52. Ground for Workbench Be sure to place a conductive sheet or copper plate with proper grounding (1 M) on the workbench or other s

29、urface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing. Instructions for Handling Semiconductors Electrostatic breakdown of the semi-condu

30、ctors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 M) that is properly grounded to remove any static electricity that may be charged on the body. 1 - 6Safety and important notice W

31、arning Risk of overheating! Never install the Home Theater System in a confi ned space. Always leave a space of at least 4 inches around the Home Theater System for ventilation. Ensure curtains or other objects never cover the ventilation slots on the Home Theater System. Never place the Home Theate

32、r System, remote control or batteries near naked fl ames or other heat sources, including direct sunlight. Only use this Home Theater System indoors. Keep this Home Theater System away from water, moisture and liquid-fi lled objects. Never place this Home Theater System on other electrical equipment

33、. Keep away from this Home Theater System during lightning storms. Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. Visible and invisible laser radiation when open. Avoid exposure to beam. Recycle notice This electron

34、ic equipment contains a large number of materials that can be recycled or reused if disassembled by a specialized company. If you are disposing of an old machine, please take it to a recycling center. Please observe the local regulations regarding disposal of packaging materials, exhausted batteries

35、 and old equipment. Copyright notice This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must

36、be authorised by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision Corporation. Reverse engineering or disassembly is prohibited. About Progressive Scan Consumers should note that not all high defi nition television sets

37、are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 or 625 progressive scan picture problems, it is recommended that the user switch the connection to the standard defi nition output. If there are questions regarding our TV set compatibility

38、with this model 525p and 625p DVD player, please contact our customer service center. 1 - 7LOCATION OF PCB BOARDS VERSION VARIATION: HTS3172 Type/Versions Features /93 /98 Output Power-200W Voltage(220V-240V) MP3 Link SERVICE SCNARIO MATRIX: HTS3172 Type/Versions Board in used /93 /98 DECODE board C

39、 C POWER board C C AMP board C C LED board C C KEY board C C *C=Com ponent Level Repair KEY BOARD LED BOARD POWER BOARDAMP BOARD DECODE BOARD 2 - 1(Open/Close ) Opens or closes the disc compartment. Source buttons AUDIO SOURCE : Selects an audio input source. RADIO : Switches to FM band. USB : Switc

40、hes to the USB source. DISC : Switches to the disc source. SETUP Accesses or exits the setup menu. (Navigation buttons ) Navigates through the menus. Press left and right for fast backward or forward search. In radio mode, press up and down to tune the radio frequency. In radio mode, press left or r

41、ight to start auto search. INFO For discs, displays information about the current status or the disc. For slideshows, displays a thumbnail view of photo fi les. (Play/Pause ) Starts, pauses or resumes disc play. In radio mode, automatically tunes radio stations during fi rst-time setup. (Stop ) Stop

42、s disc play. In radio mode, erases the current preset radio station. SURR (Surround Sound) Switches to supported surround sound or stereo sound. AUDIO SYNC Selects an audio language or channel on a disc. Press and hold to access the setting for audio sync, then press VOL +/- to set the audio delay t

43、ime. 1_hts3172_93_eng1b.indd Sec1:7 Numeric buttons Selects an item to play. SUBTITLE Selects the subtitle language on a disc. VOCAL Changes the audio channel of a karaoke disc. MIC (VOL +/-) Increases or decreases microphone volume. REPEAT / PROGRAM Selects or turns off repeat or shuffl e mode. In radio mode, resets the list of preset stations: press to manually reset; press and hold to auto