Philips-HTS-3164-Service-Manual电路原理图.pdf

《Philips-HTS-3164-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-HTS-3164-Service-Manual电路原理图.pdf（37页珍藏版）》请在收音机爱好者资料库上搜索。

1、1 1HTS3164/05/12 Copyright 2008 Philips Consumer Electronics B.V. Eindhoven, The NetherlandsAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system ortransmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwisewithout the prior

2、 permission of Philips.P ublis hed b y LM0815 Serv i c e Audio P rint ed in The Net herlands Subject to modi f icat ionDVD Home Theater SystemVersion 1.1TABLE OF CONTENTSLocation of PCB Boards . 1-2Versions Variation . 1-2Measurement Setup . 1-4Specifications. 1-3Service Aids. 1-5ESD 50HzPower Consu

3、mption . 60 WDimensions . . . . . . . . . . . . . . . 360 x 58 x 332 (mm).(w x h x d)Weight .2.8 kgFRONT AND REAR SPEAKERSSystem . . . . . . . . . . . . . . . Full range satelliteImpedance . . . . . . . . . . . . . . .4uniF053Speaker drivers .3” full range speakerFrequency response . . . . . . . . .

4、 . . . . . .150 Hz 20 kHzDimensions . . . . . . . . . . . . . . . 103 x 203 x 71 (mm).(w x h x d)Weight .0.45 kg/eachCENTRE SPEAKERSystem . . . . . . . . . . . . . . . Full range satelliteImpedance . . . . . . . . . . . . . . .8uniF053Speaker drivers .3” full range speakerFrequency response . . . .

5、. . . . . . . . . . .150 Hz 20 kHzDimensions . . . . . . . . . . . . . . . 103 x 244 x 74 (mm).(w x h x d)Weight .0.78 kgSUBWOOFERImpedance . . . . . . . . . . . . . . .8uniF053Speaker drivers . 165mm (6.5”) wooferFrequency response . . . . . . . . . . . . . . .40 Hz 150 HzDimensions . . . . . . . .

6、 . . . . . . . 123 x 310 x 369 (mm).(w x h x d)Weight .3.85 kgSpeci cations subject to change without prior notice.1 - 4LF Generator e.g. PM5110RecorderUse Universal Test Cassette CrO2 SBC419 4822 397 30069LEVEL METERe.g. Sennheiser UPM550with FF-filterS/N and distortion metere.g. Sound Technology S

7、T1700BLRDUTor Universal Test Cassette Fe SBC420 4822 397 30071LEVEL METERe.g. Sennheiser UPM550with FF-filterS/N and distortion metere.g. Sound Technology ST1700BLRDUTCDUse Audio Signal Disc(replaces test disc 3)SBC429 4822 397 30184Bandpass250Hz-15kHze.g. 7122 707 48001LF Voltmetere.g. PM2534DUTRF

8、Generator e.g. PM5326S/N and distortion metere.g. Sound Technology ST1700BUse a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).Ri=50Tuner FMMEASUREMENT SETUP1 - 5Service Tools:Universal Torx driver holder .4822 395 91019Torx bit T10 150mm .4822 395 5

9、0456Torx driver set T6-T20 .4822 395 50145Torx driver T10 extended .4822 395 50423Compact Disc:SBC426/426A Test disc 5 + 5A .4822 397 30096SBC442 Audio Burn-in test disc 1kHz .4822 397 30155SBC429 Audio Signals disc .4822 397 30184Dolby Pro-logic Test Disc .4822 395 10216SERVICE AIDSHANDLING CHIP CO

10、MPONENTS1 - 61 - 72 - 12 - 1Current model HTS3164/05/12 Version: 00.13.00_1 Release: 2007.12.22region : 2 Servo: 5B.61.00.00 8032: 05.00.04.06 RISC: 00.00.02.01MCU: V06.06 IF current model does not match you set use down arrow key on the remote to changeOKSystem , Region Code , etc. Setting Produre1

11、)System Reseta) Press “OPTIONS“ button on R/C,TV will show setup menub) Select the menu using the and on R/Cc) Go preference page to do system reset2)Region Code Changea) Open the CD Door, press”9” “9“ “9“ “9“ on R/C,then input desired number to change region code :1 USA2 EU3 AP4 Australia ,NZ , Lat

12、am5 Russia , INDIA6 CHINA3)Version Control Changea) In open model, press “1“ “5“ “9“ on R/Cb) Press “ok” button to conf_i rmc) TV will show message as below:7) Upgrading new sofewarea) Copy “sofeware f_i les” into a CD-Rb) Open the CD Door,the insert CD into USB jack in the front panel c) Close the

13、CD Doord) VFD will show:“Loading“Erase” - erase the f_l ash memory “Writing” about 1 minute“done “ * The system will switch off and on again automatically.e) OSD will show:CAUTION!This information is confi dential and may not be distributed.Only a qualifi ed service person should reprogram the Regio

14、n Code.4)Password Changea) Press “OPTIONS “ button on R/C,TV will show setup menub) Select the menu using thetriangledwn and trianglert on R/Cc) Go preference page select “password“ to change * 000000 is default password supplied.5)Check on the Sofeware Versiona) Open the CD Doorb) Press “INFO“ butt

15、on on R/C c) TV will show the version on screenupgrade f_i le detectedDo you wish to continue withthe sofeware upgrade?OK Cancelf) Select “OK”, OSD will show:upgrade in process.V316Xplease do not unplug orswitch off the device.6)Trade modela) Press “Open/Close “ button on R/Cb) Press “2” “5” “9” on R/C,VFD will display “TRA ON “ or “TRA OFF“2 - 22 - 2REPAIR INSTRUCTIONS (part one)2 - 32 - 3REPAIR INSTRUCTIONS (part two)