Philips-HTS-3376-Service-Manual电路原理图.pdf

《Philips-HTS-3376-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-HTS-3376-Service-Manual电路原理图.pdf（38页珍藏版）》请在收音机爱好者资料库上搜索。

1、1 - 1HTS3376/12Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The NetherlandsAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system ortransmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwisewithout the prior p

2、ermission of Philips.Published by RY0924 Service Audio Printed in The Netherlands Subject to modificationDVD Home Theater SystemVersion 1.1TABLE OF CONTENTSLocation of PCB Boards . 1-2Versions Variation . 1-2Measurement Setup . 1-4Specifications . 1-3Service Aids . 1-5ESD 50 HzPower consumption . .

3、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 WStandby power consumption . 1 WDimensions (WxHxD) . 360 x 57 x 331 (mm)Weight .2.87 kgSpeakersSystem . . . . . . . . . . . . . . . full range satelliteSpeaker impedance . . . . . . . .

4、. . . 4 ohm (centre), 4 ohm (Front/Rear)Speaker drivers .Centre/Front/Rear . . . . . . . . . . . . . . . 3” full rangeFrequency response . . . . . . . . . . . . . . .150 Hz 20 kHzDimensions (WxHxD) .- Centre . . . . . . . . . . . . . . . 244 x 103 x 74 (mm)- Front . . . . . . . . . . . . . . . 103 x

5、 203 x 71 (mm)- Rear . . . . . . . . . . . . . . . 262 x 1199 x 264 (mm)Weight .- Centre . . . . . . . . . . . . . . .0.79 kg- Front . . . . . . . . . . . . . . .0.54 kg- Rear . . . . . . . . . . . . . . .3.38 kgSubwooferImpedance . . . . . . . . . . . . . . . 4 ohmSpeaker drivers . 165 (6.5”) woofe

6、rFrequency response . . . . . . . . . . . . . . .40 Hz 150 HzDimensions (WxHxD) . 163 x 363 x 369 (mm)Weight .4.85 kgLaser specificationType . . . . . . . . . . . . . . . Semiconductor laser GaAIAs (CD)Wave length . . . . . . . . . . . . . . . 645 - 665 nm (DVD),770 - 800 nm (CD)Output power . . . .

7、 . . . . . . . . . . .6 mW (DVD),7 mW (VCD/CD)Beam divergence . . . . . . . . . . . . . . . 60 degrees.Specif_i cations subject to change without prior notice.1 - 4LEVEL METERe.g. Sennheiser UPM550with FF-filterS/N and distortion metere.g. Sound Technology ST1700BLRDUTCDUse Audio Signal Disc(replace

8、s test disc 3)SBC429 4822 397 30184Bandpass250Hz-15kHze.g. 7122 707 48001LF Voltmetere.g. PM2534DUTRF Generator e.g. PM5326S/N and distortion metere.g. Sound Technology ST1700BUse a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).Ri=50Tuner FMMEASUREM

9、ENT SETUP1 - 5Service Tools:Universal Torx driver holder .4822 395 91019Torx bit T10 150mm .4822 395 50456Torx driver set T6-T20 .4822 395 50145Torx driver T10 extended .4822 395 50423Compact Disc:SBC426/426A Test disc 5 + 5A .4822 397 30096SBC442 Audio Burn-in test disc 1kHz .4822 397 30155SBC429 A

10、udio Signals disc .4822 397 30184Dolby Pro-logic Test Disc .4822 395 10216SERVICE AIDSHANDLING CHIP COMPONENTS1 - 61 - 72 - 12 - 1System , Region Code , etc. Setting Produre1)System Reseta) Press “SETUP“ button on R/C,TV will show setup menub) Select the menu using the and on R/Cc) Go preference pag

11、e to do system reset2)Region Code Changea) In open mode, press”9” “9“ “9“ “9“ on R/C,then input desired number to change region code :1 USA2 EU3 AP4 Australia ,NZ , Latam5 Russia , INDIA6 CHINA3)Version Control Changea) In open mode, press “1“ “5“ “9“ on R/Cb) Press “ok” button to conf_i rmc) TV wil

12、l show message as below:7) Upgrading new softwarea) Copy “software f_i les” into a CD-Rb) Open the CD Door,then insert the CD-R program disc c) Close the CD Doord) VFD will show:“Loading“Erase” - erase the f_l ash memory “Writing” about 1 minute“done “ * the system will switch off and on again autom

13、atically.e) OSD will show:Current model HTS3377/12/05 Version: XX.XX.XX Release:XXXX.XX.XXregion :2 Servo:XX.XX.XX.XX 8032:XX.XX.XX.XX RISC: XX.XX.XX.XX MCU:XX.XX If current model does not match you set use down arrow key on the remote to changeOKCAUTION!This information is confi dential and may not

14、 be distributed.Only a qualifi ed service person should reprogram the Region Code.4)Password Changea) Press “SETUP“ button on R/C,TV will show setup menub) Select the menu using the and on R/Cc) Go preference page select “password“ to change * 000000 is default password supplied.5)Check on the Softw

15、are Versiona) Open the CD Doorb) Press “INFO“ button on R/C c) TV will show the version on screenupgrade f_i le detectedDo you wish to continue withthe software upgrade?OK Cancelf) Select “OK”, OSD will show:upgrade in progress.V337Xplease do not unplug orswitch off the device.6)Trade modela) Press “Open/Close “ button on R/Cb) Press “2” “5” “9” on R/C,VFD will display “TRA ON “ or “TRA OFF“2 - 22 - 2REPAIR INSTRUCTIONS (ONE)2 - 32 - 3REPAIR INSTRUCTIONS (TWO)