Philips-HTS-3562-Mk2-Service-Manual电路原理图.pdf

《Philips-HTS-3562-Mk2-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-HTS-3562-Mk2-Service-Manual电路原理图.pdf（59页珍藏版）》请在收音机爱好者资料库上搜索。

1、Copyright 2010 Philips Consumer Electronics B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of

2、 Philips.Version 1.Version 0.0 LASER PRODUCT TABLE OF CONTENTS Page Production Speci cations .1-3 D Instruction.2-1 Mechanical and Dismantling Instructions .3-1 Software Upgrades. -1 Trouble Shooting Chart . -1 Set Mechanical Exploded view . -1 Revision List . Location of PCB Boards & version variat

3、ion & repair scenario matrix.1-2 CLASS 1 GB 313978536081 Published by Helen-RY 1207 Service Audio Printed in The Netherlands Subject to modification Wiring Diagrams .6-1 Electrical Diagrams and Print-layouts .7-1 Safety Instruction, Warning & Notes.1- 8 9-1 Version 1.1 6 Home Theater BD Player FU 4

4、5 Service HTS3562/98 GB Second Generation This service manual is for HTS3562 Second Generation model, which is different from the previous generation HTS3562/98 model. For Second Generation model the serial number begin with KX2AXXXXXXXXXX.Refer to the rating lable illustration at right.MAINBOARD AM

5、PLIFIERBOARD LOADER POWERBOARD PCBBOARDLOCATION:Version Variation HTS3562M2 Type/Versions Features /98 Power supply rating:110-240V ,5060Hz X Power consumption:110W X Repair Scenario Matrix HTS3562M2 Type/Versions Board in used /98 Main Board C Front Control Board C Amplifier Board C Power Board C *

6、Bd:Board Level Replacement *C:Component Level Repair Note Speci cations and design are subject to change without notice. Region codes The type plate on the back or bottom of the home theater shows which regions it supports. Media formats AVCHD, BD, BD-R/ BD-RE, BD-Video, DVD-Video, DVD+R/+RW, DVD-R/

7、-RW, DVD+R/-R DL, CD-R/CD-RW, Audio CD, Video CD/SVCD, Picture les, MP3 media, WMA media, DivX Plus HD media, USB storage device RMVB (Available only in Asia Paci c and China) File formats Audio: .aac, .mka, .mp3, .wma, .wav, .mp4, .m4a Video: .avi, .divx, .mp4, .mkv, .asf, .wmv, .mpg, .mpeg, .rmvb,

8、 .rm (Available only in Asia Paci c and China) Picture: .jpg, .jpeg, .gif, .png Ampli er T otal output power: 600W RMS (30% THD) Frequency response: 20 Hz-20 kHz / 3 dB Signal-to-noise ratio: 65 dB (CCIR) / (A-weighted) Input sensitivity: AUX: 2 V Music iLink: 1 V Country A A Asia Pasific, Taiwan, K

9、orea DVD BD Video Signal system: PAL / NTSC HDMI output: 480i/576i, 480p/576p, 720p, 1080i, 1080p, 1080p24 Audio S/PDIF Digital audio input: Coaxial: IEC 60958-3 Optical: T OSLINK Sampling frequency: MP3: 32 kHz, 44.1 kHz, 48 kHz WMA: 44.1 kHz, 48 kHz Constant bit rate: MP3: 32 kbps - 320 kbps WMA:

10、48 kbps - 192 kbps Radio Tuning range: Europe/Russia/China: FM 87.5-108 MHz (50 kHz) Asia Paci c/Latin America: FM 87.5-108 MHz (50/100 kHz) Signal-to-noise ratio: FM 45 dB Frequency response: FM 180 Hz-12.5 kHz / 3 dB USB Compatibility: Hi-Speed USB (2.0) Class support: USB Mass Storage Class (MSC)

11、 File system: FAT16, FAT32, NTFS Maximum memory support: 160 GB Main unit Power supply: 110-240 V, 50-60 Hz Power consumption: 110 W Standby power consumption: 0.9 W - 0.5 W Dimensions (WxHxD): 360 x 58 x 325 mm Weight: 2.62 kg Subwoofer Output power: 100 W RMS (30% THD) Impedance: 4 ohm Speaker dri

12、vers: 133 mm (5.25“) woofer Dimensions (WxHxD): 160 x 267.5 x 265 mm Weight: 2.55 kg Product Specifications: 1-3Speakers Center speaker: Output power: 100 W RMS (30% THD) Speaker impedance: 4 ohm Speaker drivers: 1 x 63.5 mm (2.5“) woofer Dimensions (WxHxD): 160 x 85 x 95 mm Weight: 0.37 kg Front/Re

13、ar speaker: Output power: 4 x 100 W RMS (30% THD) Speaker impedance: 4 ohm Speaker drivers: 1 x 76.2 mm (3“) twin driver Dimensions (WxHxD): Speakers: 85 x 160 x 95mm Tall speakers: 240 x 1007 x 240 mm Weight: Speakers: 0.35 kg/each Tall speakers: 1.57 kg/each Remote control batteries 2 x AAA-R03-1.

14、5 V Laser Laser Type (Diode): InGaN/AIGaN (BD), AIGaInP (DVD/CD) Wave length: 405 +7 nm/-7 nm (BD), 655 +10 nm/-10 nm (DVD), 790 +10 nm/-20 nm (CD) Output power (Max. ratings): 20 mW (BD), 6 mW (DVD), 7 mW (CD) 1-4Safety instruction 1. General safety Safety regulations require that during a repair:

15、. Connect the unit to the mains via an isolation transformer. . Replace safety components indicated by the symbol , only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard. Safety regulations

16、require that after a repair, you must return the unit in its original condition. Pay, in particular, attention to the following points: . Route the wires/cables correctly, and fix them with the mounted cable clamps. . Check the insulation of the mains lead for external damage. . Check the electrical

17、 DC resistance between the mains plug and the secondary side: 1) Unplug the mains cord, and connect a wire between the two pins of the mains plug. 2) Set the mains switch the “on” position (keep the mains cord unplug). 3) Measure the resistance value between the mains plug and the front panel, contr

18、ols, and chassis bottom. 4) Repair or correct unit when the resistance measurement is less than 1M . 5) Verify this, before you return the unit to the customer/user (ref. UL-standard no. 1492). 6) Switch the unit “off”, and remove the wire between the two pins of the mains plug. 2.Laser safety This

19、unit employs a laser. Only qualified service personnel may remove the cover, or attempt to service this device (due to possible eye injury). Laser device unit T ype : Semiconductor laser GaAlAs Wavelength : 650nm (DVD) : 780nm (VCD/CD) Output power : 7mW (DVD) : 10mW (DVD /CD) Beam divergence: 60 de

20、gree Note: Use of controls or adjustments or performance of procedure other than those specified herein, may result in hazardous radiation exposure. Avoid direct exposure to beam. Safety instruction, Warning & Notes 1-5Warning 1.General . All ICs and many other semiconductors are susceptible to elec

21、trostatic discharges (ESD). Careless handing during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: 1) Complet

22、e kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. 2) Wristband tester 4822 344 13999. . Be careful during measurements in the live voltage section. The primary side of the power supply , including the heat sink, carries live mains voltage when yo

23、u connect the player to the mains (even when the player is “off”!). It is possible to touch copper tracks and/or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A “lighting stro

24、ke” and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply. . Never replace modules, or components, while the unit is “on”. 2. Laser . The use of optical instruments with this product, will increase eye hazard. . Only qualified service personnel may r

25、emove the cover or attempt to service this device, due to possible eye injury. . Repair handing should take place as much as possible with a disc loaded inside the player. . Text below is placed inside the unit, on the laser cover shield: Notes: Manufactured under licence from Dolby Laboratories. Th

26、e double-D symbol is trademarks of Dolby Laboratories, Inc. All rights reserved. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN, AVOID EXPOSURE TO BEAM. 1-6 Solder Joint 1-7Lead-Free requirement for service INDENTIFICATION: Regardless of special logo (not always indicated) One must treat a

27、ll sets from 1.1.2005 onwards, according next rules. Important note: In fact also products a little older can also be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this. Due to lead-free technolog

28、y some rules have to be respected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops should be

29、 avoided because paste is not easy to store and to handle. Use only adequate solder tools applicable for lead-free solder alloy. The solder tool must be able o To reach at least a solder-temperature of 400C, o To stabilize the adjusted temperature at the solder-tip o To exchange solder-tips for diff

30、erent applications. Adjust your solder tool so that a temperature around 360C 380C is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400C otherwise wear-out of tips will rise drastically and flux-fluid will be destroyed.

31、 To avoid wear-out of tips switch off un-used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid, clean carefully the solder-joint

32、from old solder alloy and re-solder with new solder alloy (SAC305). Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs: - always use the 12nc-recognizable soldering tempera

33、ture profile of the specific BGA (for de-soldering always use highest lead-free temperature profile, in case of doubt) - lead free BGA-ICs will be delivered in so-called dry-packaging (sealed pack including a silica gel pack) to protect the IC against moisture. After opening, dependent of MSL-level

34、seen on indicator-label in the bag, the BGA-IC possibly still has to be baked dry. This will be communicated via AYS-website. Do not re-use BGAs at all. For sets produced before 1.1.2005, containing leaded soldering-tin and components, all needed spare-parts will be available till the end of the ser

35、vice-period. For repair of such sets nothing changes. On our website: www.atyourservice.ce.P You find more information to: BGA-de-/soldering (+ baking instructions) Heating-profiles of BGAs and other ICs used in Philips-sets You will find this and more technical information within the “magazine”, ch

36、apter “workshop news”. For additional questions please contact your local repair-helpdesk. Notes 1-8User manual EN Before using your product, read all accompanying safety information MS Sebelum menggunakan produk anda, baca semua maklumat keselamatan yang disertakan Brief Guide 2-11 FRONT RIGHT FRONT LEFT FRONT CENTER FRONT RIGHT FRONT LEFT FRONT CENTER REAR RIGHT REAR LEFT SUB- WOOFER REAR LEFT SUB WOOFER REAR RIGHT SUB WOOFER FRONT LEFT FRONT CENTER FRONT RIGHT REAR RIGHT RE