Rotel-RB-1080-Service-Manual电路原理图.pdf

《Rotel-RB-1080-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Rotel-RB-1080-Service-Manual电路原理图.pdf（6页珍藏版）》请在收音机爱好者资料库上搜索。

1、T echnical Manual STEREO POWER AMPLIFIER RB-1080 Table of Contents Specification Specification. 1 Parts List. 2,3 Adjustment. 3 Case Outlines. 3 Note On Safety. 4 PCB Assembly. 4,6 Schematic Diagram. 7,8 Continuous Power Output(20-20 kHz, 0.03%, 8 ohms) 200 watts/ch. (20-20 kHz, 0.05%, 4 ohms) 300 w

2、atts/ch. Total Harmonic Distortion(20 Hz-20 kHz, 8 ohms) 0.03% Intermodulation Distortion(60 Hz: 7 kHz, 4:1) 0.03% Frequency Response 10-100,000 Hz, 1 dB Damping Factor(20-20,000 Hz, 8 ohms) 500 Speaker Impedance 4-16 ohms Signal to Noise Ratio(IHF A network)120 dB Input Impedance/Sensitivity(RCA In

3、puts)33 k Ohms/1.0 volt (XLR Inputs)33k Ohms/1.0 volt Power Requirements115 Volts, 60 Hz or 230 Volts, 50 Hz Power Consumption 550 Watts Dimensions (W, H, D)440 x 127 x 385 mm 17.38 x 4.76 x 15.16” inches Weight(net)16.7 kg., 36.74 lb. SHINSEN-BLD. 4F 10-10 SHINSEN-CHO, SHIBUYA-KU, TOKYO 150-0045, J

4、APAN Serial. NO. Begining Quality Uncompromised Y-337A-00125M/S-S RadioFans.CN 收音机爱 好者资料库 2 Parts List-1 C601.602 C603.604 C607.608 C609.610 C611.612 C613-616 C623-626 C627.628 D601-608 D609-612 FU601-604 Q601-606 Q607-612 Q613.614 Q615.616 Q619.620 Q621.622 R601.602 R603.604 R605.606 R607-610 R611.

5、612 R613.614 R615-618 R619.620 R621.622 R623.624 R625.626 R627.628 R629.630 R631.632 R633.634 R635-654 R657.658 R659-662 R663.664 R665.666 R667-670 TH601.602 VR601.602 C801 C802 C803 X-1177-01,02 PCB ASSY 041 50BGF4R7M 044 TFKP2-2A681H 041 25BGF100M 044 FSC160V331H 054 TMF1/4-3302F 041 50BGF10M 044

6、FSC160V561H 041 VX2A102S 044 FSC160V471H 034 T1N4148-86 034 T1N4003-TB 036 5ST6.3 033 TC2362-FG 033 TA1016-FG 033 A1209-ST 033 C2911-ST 033 TC2910-RST 033 TA1208-RST 054 EE10-102 054 EE10-333 054 EE10-471 054 TMFR401K5 054 TMFR4220R 054 TMF1/4-5600F 054 TMFR401K5 054 TMFR4220R 054 TMFR4047K 054 TMFR

7、4100R 054 TMF1/4-6801F 054 TMF1/4-3901F 054 TMFR4100R 054 TMFR4001K 054 TMFR4047R 054 MPC78-0.22F 054 TMFR415K4 054 2WS6.8KJF 054 TMFR4010R 054 TMF3300 054 TMFR4220R 034 TTC-503 051 SFR001-222 017 C-4378A01 019 TO-126 066 4TR-2487#7 066 4TR-2487#8 068 C-4349A04 069 C-3417A 069 C-4446A00 X-1237-02 PC

8、B ASSEMBLY 069 C-4370A00 X-1237-03 PCB ASSEMBLY 041 UTES2A220-FB 041 UTES1E101-FB 041 UTES2A221 CAPACITOR ELEC.50V4.7UF CAPACITOR FILM 100V680PF CAPACITOR ELEC.25V100UF CAPACITOR STYROL 160V330PF RESISTOR MRS25 33K CAPACITOR ELEC.50V10UF CAPACITOR STYROL 160V560PF CAPACITOR ELEC.100V1000UF CAPACITOR

9、 STYROL 160V470PF DIODE DIODE MINI FUSE 250VT6.3A TRANSISTOR(2SC2362K-FG) TRANSISTOR(2SA1016K-FG) TRANSISTOR(2SA1209-ST) TRANSISTOR(2SC2911-ST) TRANSISTOR(2SC2910-RST) TRANSISTOR(2SA1208-RST) RESISTOR METAL 1K RESISTIR METAL 33K RESISTOR METAL 470R RESISTOR METAL 1% 1.5K RESISTOR METAL 1% 220R RESIS

10、TOR MRS25 560R RESISTOR METAL 1% 1.5K RESISTOR METAL 1% 220R RESISTOR METAL 1% 47K RESISTOR METAL 1% 100R RESISTOR MRS25 6.8K RESISTOR MRS25 3.9K RESISTOR METAL 1% 100R RESISTOR METAL 1% 1K RESISTOR METAL 1% 47R RESISTOR METAL 2W 0.22R RESISTOR METAL 1% 15.4K RESISTOR METAL 2W 6.8K RESISTOR METAL 1%

11、 10R RESISTOR METAL 330R RESISTOR METAL 1% 220R THERMISTOR SEMI-FIXED RESISTOR 2.2K HEAT SINKER INSULATION SHEET 1P PINJACK (RED) 1P PINJACK (WHT) 3P CONNECTOR WIRE FUSE CLIP SCREW TERMINAL SCREW TERMINAL CAPACITOR ELEC.100V22UF CAPACITOR ELEC.25V100UF CAPACITOR ELEC.100V220UF C804 D801 D802 D803-80

12、6 D807.808 Q801-803 R801 R803 R804 R805 R806 R807 R809 R811.812 R813.814 R815.816 R817.818 C901.902 D901.902 Q901 Q902 R901.902 R903.904 RY901 S901 C501.502 C505-508 IC501.502 R501-504 R505-508 R509.510 C001 S901 C101 C102 D101 D102 F101 Q101 R101 R102 R103 RY101 T101 041 UTES2A220-FB 034 T1N4148-86

13、 034 RD10EB 034 T1N4003-TB 034 T1N4148-86 032 TC2362-FG 054 1WS6.8KJF 053 CR14-104J-A 053 CR14-224J-A 053 CR14-104J-A 053 CR14-333J-A 053 CR14-104J-A 054 1WS6.8KJF 053 CR14-104J-A 053 CR14-183J-A 053 CR14-332J-A 053 CR14-273J-A X-1237-04 PCB ASSEMBLY 041 25BGF470M 034 RD16EB 033 D600-EF 033 B631-EF

14、054 1WS2.2KJF 054 1WS5.6KJF 063 V23106-24 064 4TR-2341 017 C-4401A01 019 TO-126 X-1237-05,06 PCB ASSY 044 S50V100PJ 041 25BGF100M 031 AD711JN 054 TMFR4022K 054 TMFR4010K 054 TMFR4001K 066 C-4575A01 X-1283 PCB ASSEMBLY 044 DE1307E472M 061 C-4176A07 X-1291-01 PCB ASSEMBLY 041 UTES1E471 044 DE1307E472M

15、 034 W02M 034 T1N4148-86 036 5ST500 032 TC3708-ST 054 1WS120JF 053 CR14-333J-A 053 CR14-152J-A 063 OZ-SH-112LM1 022 T-1075N01 069 C-3417A CAPACITOR ELEC.100V22UF DIODE ZENER DIODE DIODE DIODE TRANSISTOR(2SC2362K-FG) RESISTOR METAL 1W 6.8K RESISTOR CARBON 100K RESISTOR CARBON 220K RESISTOR CARBON 100

16、K RESISTOR CARBON 33K RESISTOR CARBON 100K RESISTOR METAL 1W 6.8K RESISTOR CARBON 100K RESISTOR CARBON 18K RESISTOR CARBON 3.3K RESISTOR CARBON 27K CAPACITOR ELEC.25V470UF ZENER DIODE TRANSISTOR(2SD600K-EF) TRANSISTOR(2SB631K-EF) RESISTOR METAL 1W 2.2K RESISTOR METAL 1W 5.6K RELAY (PROTECTION) SLIDE

17、 SWITCH HEAT SINKER INSULATION SHEET CAPACITOR STYROL 50V100PF CAPACITOR ELEC.25V100UF IC(OPE AMP) RESISTOR METAL 1% 22K RESISTOR METAL 1% 10K RESISTOR METAL 1% 1K CANNON CONNECTOR SPARK KILLER POWER SWITCH CAPACITOR ELEC.25V470UF SPARK KILLER BRIDGED DIODE DIODE MINI FUSE 250VT500MA TRANSISTOR RESI

18、STOR METAL 1W 120R RESISTOR CARBON 33K RESISTOR CARBON 1.5K RELAY (POWER) SUB TRANSFORMER FUSE CLIP SYMBOL PARTS NO.DESCRIPTIONSYMBOL PARTS NO.DESCRIPTION RadioFans.CN 收音机爱 好者资料库 3 Parts List-2 Instruments : DC millivoltmeter Notes : Prior to Bias Adjustment, run about 5minutes with rated output(8oh

19、ms) and warm up Power Transistor and Heat Sink. Set input off. StepCoupling TP 3 - TP 1 TP 4 - TP 2 X-1177-01 PCB X-1177-02 PCB VR601 VR602 1 2 LocationAdjustAdjust for DC millivoltmeter reads 7mV Adjustment Case Outline D103.104 D105 D106 IC101 K103 R104 R105 S101 TJ101.102 Q617.618 Q623-632 Q633.6

20、34 Q635.636 Q637-646 X-1291-02 PCB ASSEMBLY 034 T1N4148-86 034 TRD12JST1 034 T1N4148-86 031 PC817B 068 C-4588A09 054 1WS1KJF 053 CR14-221J-A 064 C-4613A01 065 YKB21-5103A HEAT SINKER ASSEMBLY 032 D1953 033 A1492-OPY 033 B817-DE 033 D1047-DE 033 C3856-OPY 017 PX4-06A00 019 TO-3P OTHERS 011 FP-530 011

21、 RV4-02A05 012 RV4-09A00 013 RM4-10A00T 014 RV3-07A01 DIODE ZENER DIODE DIODE PHOTO COUPLER CONNECTOR WITH WIRE RESISTOR METAL 1W 1K RESISTOR CARBON 220R TOGGLE SWITCH (TRIGGER) MINI JACK TRANSISTOR(2SD1953) POWER TRANSISTOR(2SA1492-OPY) DRIVER TRANSISTOR(2SB817-DE) DRIVER TRANSISTOR(2SD1047-DE) POW

22、ER TRANSISTOR(2SC3856-OPY) HEAT SINKER INSULATION SHEET SUB PANEL ASSY H/S PANEL PUSH KNOB 14F EARTH PLATE UPPER COVER 015 RP-381 019 4TSH-19#2 022 T-1037W04 034 BR154 034 SEL1124R 036 3AG125V12A 036 5ST6.3 041 ALS30S1077XX 044 KT18-2A104K 054 2WS10JF 067 4TR-2744#1 067 4TR-2744#2 069 C-4200A01 069

23、C-4595A00 069 C-4637A00 072 C-4392A02 072 C-4393A03 072 C-4423A03 072 C-4639A01 081 TK4-01A00 081 Z-200 REAR CHASSIS PLASTIC FOOT 50F POWER TRANSFORMER POWER DIODE LED 1X5 LONG FUSE 125V12A for STD MINI FUSE 250VT6.3A for CEE CAPACITOR ELEC.80V15000UF CAPACITOR FILM 100V0.1UF RESISTOR METAL 2W 10R S

24、PEAKER TERMINAL (RED) SPEAKER TERMINAL (WHT) LONG FUSE HOLDER for STD MINI FUSE HOLDER for CEE AC INLET AC CORD SET for STD AC CORD SET for CEE AC CORD SET for AUSTRALIA AC CORD SET for UK INSIDE CARTON STYROL MOULDING SYMBOL PARTS NO.DESCRIPTIONSYMBOL PARTS NO.DESCRIPTION NOTE ON SAFTY : Symbol Fir

25、e or electrical shock hazard. Only original parts should be used to replaced any part marked with symbol . Any other component substitution (other than original type), may increase risk of fire or electrical shock hazard. 2SA1016K 2SA1208 2SC2362K 2SC3708 2SC2910 2SB631K 2SA1209 2SD1953 2SD600K 2SC2

26、911 2SA1492 2SB817 2SC3856 2SD1047 PC817BAD711JN 4 PCB Assembly Service Note Cautions during Inspection and Repair 1. Keep in mind the safety warnings The safety instructions are shown as the labels or printings on the exterior, the inside chassis or the parts, etc. Refer to the instructions when pr

27、oceeding with inspection or repair. 2. Use only the specified parts for replacement The selected parts are used at critical area to reduce fire hazard or electrical shock. So when replacing these parts where designaged with marks or marks on the schematic diagram or the parts list, ensure to use onl

28、y the same parts. 3. Ensure to dress back the AC (Mains) cord to the original position If for some reason, the AC cord is moved or partially disassembled, ensure to re- route or assemble back to the original position. The AC cord area is protected and secured by tubing and insulation materials for t

29、he sake of safety, so that no loose wire will touch and cause fire hazard and electrical shock. 4. Check for safety aspects after inspection or repair Ensure all parts, such as screws or wires, removed during inspection or repair are secured back to the original positions, and check visually for any anomaly. Also check for any electrical leakage or resistance to maintain the safety. PCB Assembly 56 78 Schematic Diagram