Sony-SCD-CE595-Service-Manual电路原理图.pdf

《Sony-SCD-CE595-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-SCD-CE595-Service-Manual电路原理图.pdf（38页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL Sony Corporation Audio Group Published by Sony Engineering Corporation US Model Canadian Model AEP Model UK Model SUPER AUDIO CD PLAYER 9-879-006-02 2005E16-1 2005.05 Ver. 1.1 2005.05 SPECIFICATIONS SCD-CE595 General LaserSemiconductor laser (Super Audio CD: = 650 nm) (CD: = 780 nm) E

2、mission duration: continuous Power requirements US, Canadian: AEP, UK: When a Super Audio CD is played Playing frequency range2 Hz to 100 kHz Frequency response2 Hz to 40 kHz (3 dB) Dynamic range100 dB or more Total harmonic distortion rate 0 0035 % or less Wow and flutterValue of measurable limit (

3、0 001 % W PEAK) or less When a CD is played Frequency response2 Hz to 20 kHz Dynamic range96 dB or more Total harmonic distortion rate 0 0039 % or less Wow and flutterValue of measurable limit (0 001 % W PEAK) or less Output connector * Output only the audio signals of the CD Jack typeOutput level L

4、oad impedance ANALOG 5 1CH OUT Phono jacks 2 Vrms (at 50 kilohms) Over 10 kilohms DIGITAL (CD) OUT OPTICAL* Square optical output connector 18 dBm(Light emitting wave length: 660 nm) 1 230 V AC, 50/60 Hz 20 V AC, 60 Hz Power consumption15 W Dimensions (w/h/d)430 110 420 mm incl projecting parts Mass

5、 (approx )5 5 kg Supplied accessories Audio connecting cordRed and White 2 (1) Remote commanderRM-SX800 (1) BatteryR6 (size-AA) (2) Design and specifications are subject to change without notice Model Name Using Similar MechanismNEW CD Mechanism TypeCDM79C-DVBU51 Optical Pick-up NameDBU-3 RadioFans.

6、CN 收音机爱 好者资料库 2 SCD-CE595 Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C during repairing. Do not touch

7、the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposu

8、re. This appliance is classified as a CLASS 1 LASER product This label is located on the rear exterior The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body

9、. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so

10、 as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT LASER DIODE AND FOCUS SEARCH OP

11、ERATION CHECK Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveform is output three times. TABLE OF CONTENTS 1.SERVICING NOTES .3 2.GENERAL .4 3.TEST MODE.6 4.DIAGRAMS 4-1.Block Diagram .8 4-2.Printed Wiring Board RF Section .9 4-3.Schematic Diagram RF Section

12、. 10 4-4.Printed Wiring Board MAIN Section . 11 4-5.Schematic Diagram MAIN Section (1/4) . 12 4-6.Schematic Diagram MAIN Section (2/4) . 13 4-7.Schematic Diagram MAIN Section (3/4) . 14 4-8.Schematic Diagram MAIN Section (4/4) . 15 4-9.Printed Wiring Board DISPLAY Section . 16 4-10. Schematic Diagra

13、m DISPLAY Section . 17 4-11. Printed Wiring Board MD-94 Board Section . 18 4-12. Schematic Diagram MD-94 Board Section . 19 5.EXPLODED VIEWS 5-1.Main Section. 22 5-2.Front Panel Section . 23 5-3.Chassis Section. 24 5-4.CD Mechanism Section (1) (CDM79C-DVBU51) . 25 5-5.CD Mechanism Section (2) (CDM79

14、C-DVBU51) . 26 6.ELECTRICAL PARTS LIST .27 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS

15、MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NU

16、MROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. RadioFans.CN 收音机爱 好者资料库 3 SCD-CE595 SECTION 1 SERVICING NOTES HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF Insert a tapering driver into the aperture of the unit bottom, and turn in the direction of arrow. Use a flat (-)

17、 head screwdriver to open the disc tray by manual operation. (Flat head screwdriver with nominal blade length of 3mm.) * To close the disc table, turn the driver in the reverse direction. tapering driver 1 2 Parts No. MODEL IDENTIFICATION Back Panel MODELPart No. US Model4-255-250-0 Canadian Model4-

18、255-250-1 AEP Model4-255-250-2 UK Model4-255-250-3 SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for A

19、C leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three

20、methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by

21、means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are

22、 suitable. (See Fig. A) Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground 4 SCD-CE595 SECTION 2 GENERAL This section is extracted from instruction manual. Front Panel A POWER switch (9) B DISC 1-5 buttons (9, 14) Press to s

23、elect the disc directly. C Remote sensor (6) D Display window (10) E H button (9, 13, 14) F X button (9) G x button (9, 15) H m/M buttons (13) I l AMS L dial (AMS: Automatic Music Sensor) (8, 9, 10, 12, 13, 14, 16, 17, 19) J EX-CHANGE button (12) Press to replace discs while playing a disc. K DISC S

24、KIP button (9, 12, 14) Press to select the disc. L A OPEN/CLOSE button (9) M Disc tray (9) N MULTI CHANNEL DECODING indicator Turns on when you turn on the player, or when the Multi-channel Super Audio CD is loaded and select the multi-channel playback area by pressing MULTI/2CH. O TIME/TEXT button

25、(11) Each time you press the button, the playing time of the track, the remaining time of the disc, or TEXT information appears in the display. P PLAY MODE button (9, 14) Press to select the play mode. Q MULTI/2CH button (5, 10) Press to select the playback area when a disc with the 2 channel area a

26、nd the multi-channel area (page 5) is loaded. R SA-CD/CD button (5, 9) Each time you press the button while playing back a hybrid disc, the layer to be played back switches between the SA-CD layer and the CD layer. S MENU button (8, 9, 10, 12, 16, 17, 19) Press to enter the menu. Press to exit from

27、the menu and return to the normal display. 12345 6 789 q; qaqsqdqfqgqhqjqkql 5 SCD-CE595 Remote A CD1/2 (command mode) switch (8) Select the command mode. B CONTINUE button (9, 14) Press to resume Continuous Play from Shuffle Play or Program Play. SHUFFLE button (14) PROGRAM button (14) C TIME/TEXT

28、button (11) Each time you press the button, the playing time of the track, the remaining time of the disc, or TEXT information appears in the display. D DISPLAY MODE button (12) Press to turn the display information off or on. E m/M buttons (13) F CLEAR button (14, 15) Press to delete a programed tr

29、ack number. G LEVEL ADJ button (17) Press to adjust the output level balance for the Multi-channel management function (page 15). H ENTER button (8, 10, 12, 14, 16, 18, 19) I CHECK button (15) Press to check the programed order. J REPEAT button (13) K H button (9, 13, 14) X button (9) x button (9, 1

30、5) L AMS ./ buttons (AMS: Automatic Music Sensor) (8, 9, 10, 12, 13, 14, 16, 18, 19) M SA-CD/CD button (5, 9) Each time you press the button while playing back a hybrid disc, the layer to be played back switches between the SA-CD layer and the CD layer. N MULTI/2CH button (5, 10) Press to select the

31、 playback area when a disc with the 2 channel area and the multi-channel area (page 5) is loaded. O DISC SKIP +/ buttons (9, 12, 14) Press to select the disc. qg qf qd qs qa q; 9 8 1 2 3 4 5 6 7 6 SCD-CE595 SECTION 3 TEST MODE 1. Setting Methed of Test Mode Press three buttons m , PUSH ENTER and POW

32、ER simulta- neously, The test mode becomes active. Then all segments of the fluorecent indicator tube are turned on. 2. FL Tube Grid, Segments Check Procedure: 1.Grid of all segments lights up sequentially starting from 1G to 16G. 2.The vertical line (total 5 lines) of all grids lights up sequential

33、ly in the range of 5G to 16 G starting from the left. 3.The horizontal line of (total 7 lines) of all grids lights up sequentially in the range of 5G to 16G starting from the top. 3. Sircs Receive Check Procedure: 1.The message “SIRCS CHECK” is displayed on the fluorecent indicator tube. 2.With the

34、machine in the status that is set in step 2, press any on the remote commander. The machine enters the key check standby state. (When the H key or the x key is pressed, the reception check is canceled.) 4. Key Check Procedure: 1.In the key check mode, the fluorecent indicator displays “KEY CHECK*”.

35、Each time a button is pressed, “*” value. However, once a button is pressed, it is no longer taken into account. 2.To exit from this mode, the message “JOG CHECK” is displayed. 5. Jog Check Procedure: 1. After the key check is completed, turn JOG clockwise to turn on the calendar segments sequential

36、ly. When the segment “15” is confirmed, turn JOG counter-clockwise that turns off the calendar segment. When the segment “1” is confirmed, this is the end of check. 6. Releasing Meted of Test Mode 1.After all the checks are completed, confirm to see that the display “TEST-END” appears. The message i

37、ndicates that the check is ended normally. 2.Press the POWER button to turn off the main power and disconnect the power plug from the wall outlet. 77 SCD-CE595 SCD-CE595 SECTION 4 DIAGRAMS Circuit Boards Location NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Board: X :

38、 parts extracted from the component side. Y : parts extracted from the conductor side. W : indicates side identified with part number. f: internal component. : Pattern from the side which enables seeing. C B These are omitted. E Q Note Schematic Diagrams. All capacitors are in F unless otherwise not

39、ed. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. f: internal component. C : panel designation. A : B+ Line. B : B Line. Voltages and waveforms are dc with respect to ground under no-signal condition

40、s. no mark: SACD PLAY ( ) : CD PLAY Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to wavefo

41、rms. Signal path. J: CD c: CD DIGITAL OUT (OPTICAL) Caution: Pattern face side: Parts on the pattern face side seen from (Side B) the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Side A) the parts face are indicated. 1.4 Vp-p 1 IC001 tl SIGO (CD) 1.4 Vp-p 1 IC

42、001 tl SIGO (SACD) 200 ns/DIV 40 ns/DIV Waveforms Indication of transistor. RF Board MAIN Board DISPLAY Board 4 IC320 2,4,6,q;,qs 1.4 Vp-p 3 IC706 AMS PUSH ENTER M m A DISC SKIP EX-CHANGE MAIN BOARD CN703 (Page 11) B TIME/TEXTPLAY MODEMULTI/2CHSA-SD/CDMENU DISC 1DISC 2DISC 3DISC 4DISC 5 MULTI CHANNE

43、L DECODING POWER AC IN MAIN BOARD CN901 (Page 11) C Semiconductor Location Ref. No.Location IC801G-14 IC802G-18 Q821G-15 Q822F-13 Q823F-12 Q824F-12 Q825F-11 Q826G-10 1717 SCD-CE595 SCD-CE595 4-10. SCHEMATIC DIAGRAM DISPLAY SECTION 15 13 -30.8 -33 -33 -33 -20 -28 -28 -32 -24 -22 -30 -29 -28 -26.5 -30

44、 -30 -30 -31 -31 -31 -31 -31 -31 -31 -31 -31 -31 -31 -31 -22.3 -28.7 -31 -33 3.3 3.3 0 1.6 3.3 0.5 EXCHANGE DISCSKIP KEY 0 3 KEY 0 3 R819 R820 R841 R851 R842R843 R852R853 R844 R854 R845 R821R822R823R824R825 R861R862R863R864 C891 R826 C831 C801 S865 S864 S863 S862 S861 S841S842S843S844S845 S851 TP5 T

45、P26 TP126 T101 R856 R857 R858 C804 C819 R817 C803 C818 C817 S855 X801 R805 C816 C811 C812 C813 FB801 C802 C822 C823 C824 C825 C829 C827 C821 C805 C806 R831 R832 C832 CN102 CN101 C101 CN892 S891 CN891 CN801 CN804 CN814 D801 CN805 IC802 FL801 R818 Q822 Q821 C833 R834 CN813 IC801 Q826 Q824 Q825 Q823 10

46、k 10k 1k 1k 2 2k2 2k 2 2k2 2k 47k 47k 10k 100k100k100k100k100k 1k2 2k2 2k47k 0 0022 250V 10k 47 6 3V 100 6 3V 10k 10k 82 0 1 0 01 10k 0.1 0.01 0.01 ENCORDER 5MHz 10k 0 001 0 001 0 001 0 001 FB 0 1 0 001 0 001 0 001 0 001 0 1 0 1 0 001 0 1 0 1 47 100 0 01 8P 2P 0 0022250V 2P 2P 13P 2P 2P SEL5E20C STP

47、15 BLUE 2P NJL73H400A 10k DTC114EKA T146 DTC114EKA T146 0 110k 2P 8BT A 2SC3624AT1L15L16 DTC114EKA T146 DTC114EKA T146 DTC114EKA T146 S852S853 S852 S853 * * * C820 0 01 25V R871R872R873R874 S875 S8774 S873 S872 S871 1k2 2k2 2k47k DISK5DISK4DISK3DISK2DISK1 See page 7 for Waveforms. 1818 SCD-CE595 SCD-CE595 4-11. PRINTED WIRING BOARD MD-94 BOARD SECTION See page 7 for Circuit Boards Location. :Uses unleaded solder. SE-130 BOARD MD-94 BOARD (13) 13 (13) 13 MAIN BOARD CN704 (Page 11) D M M001 TURN