Sony-TC-TX313-Service-Manual电路原理图.pdf

《Sony-TC-TX313-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-TC-TX313-Service-Manual电路原理图.pdf（34页珍藏版）》请在收音机爱好者资料库上搜索。

1、 TC-TX313/TX515 MICROFILM US Model Tourist Model TC-TX515 AEP Model UK Model E Model TC-TX313/TX515 SERVICE MANUAL SPECIFICATIONS Recording system4-track 2-channel stereo Frequency response(DOLBY NR OFF) 50 - 14,000 Hz ( 3 dB), using Sony TYPE I cassettes 50 - 15,000 Hz ( 3 dB), using Sony TYPE II c

2、assettes InputTAPE IN (phono jacks): impedance 47 kilohms OutputTAPE OUT (phono jacks): voltage 550 mV impedance 47 kilohms General Power requirements US model:120 V AC, 60 Hz AEP, UK model:220 - 230 V AC, 50 / 60 Hz E, Tourist model:110 - 120 V or 220 - 240 V AC, 50 / 60 Hz Adjustable with the volt

3、age selector Power consumption12 W DimensionsApprox. 215 60 195 mm (w / h / d) incl. projecting parts and controls MassApprox. 2.5 kg Supplied accessories:Audio connecting cords (2) Design and specifications are subject to change without notice. Model Name Using Similar MechanismNEW Tape Transport M

4、echanism Type Photo: TC-TX515 TC-TX313 is the optional stereo cassette deck that can be used only with section DHC-MD313. TC-TX515 is the optional stereo cassette deck that can be used only with section DHC-MD515. STEREO CASSETTE DECK SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK !

5、 OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. Notes on Chip Component Replacement Never reuse a disconnected c

6、hip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. Dolby noise reduction manufactured under license from Dolby Labo- ratories Licensing Corporation. “DOLBY” and the double-D symbol a are trademarks of Dolby Laboratories Licensing Corporation. RadioFans.CN 收音机

7、爱 好者资料库 2 TABLE OF CONTENTS 1. GENERAL Parts and Controls. 3 2. TEST MODE 2-1. Checking the Items of Test Mode . 4 3. DISASSEMBLY 3-1. Top Cover. 5 3-2. Front Panel Assy . 5 3-3. Front Board (TC-TX313). 6 3-4. Panel Board (TC-TX515). 6 3-5. Back Plate . 7 3-6. Bracket (Power Trans) . 7 3-7. Main Boa

8、rd . 8 3-8. TCM Assy . 8 3-9. Lever . 9 3-10. Tension Spring. 9 3-11. Housing . 10 3-12. Chassis . 10 3-13. Motor (A)/(B) Assy .11 3-14. Head Plate .11 3-15. Pinch Roller Assy . 12 3-16. Bracket (Head Unit) . 12 4. MECHANICAL ADJUSTMENTS. 13 5. ELECTRICAL ADJUSTMENTS. 13 6. DIAGRAMS 6-1. Circuit Boa

9、rds Location . 16 6-2. Printed Wiring Board Deck Section . 17 6-3. Schematic Diagram Deck Section. 18 6-4. Printed Wiring Boards Main Section . 20 6-5. Schematic Diagram Main Section. 23 6-6. Printed Wiring Boards Front Panel Section . 27 6-7. Schematic Diagram Front Panel Section. 29 6-8. IC Pin De

10、scription. 31 7. EXPLODED VIEWS 7-1. Top Cover Section . 33 7-2. Front Panel Section (TC-TX313). 34 7-3. Front Panel Section (TC-TX515). 35 7-4. Chassis Section . 36 7-5. TCM Assy Section . 37 8. ELECTRICAL PARTS LIST. 38 RadioFans.CN 收音机爱 好者资料库 3 SECTION 1 GENERAL TC-TX313 Parts and Controls TC-TX5

11、15 Parts and Controls 1 POWER switch Only the power to this set is turn on. 2 Cassette slot With a cassette inserted, the cassette indicator is illuminated red when the power is turned on. 3 (eject) button 4 (lower side play)/ (upper side play) button Even without cassette, the power to this set and

12、 the DHC-MD313 will be turned on when one of these buttons is pressed. 5 (pause) button 6 (stop) button 7 / (fast forward, fast backward/AMS) button 8 REC (recording) button 9 CD SYNC (CD synchro) button This button allows CD synchro recording to be executed as this set is interlocked with the DHC-M

13、D313. ! DIRECTION switch ! DOLBY NR (Dolby Noise Reduction) switch 1 POWER switch Only the power to this set is turn on. 2 Cassette slot With a cassette inserted, the cassette indicator is illuminated red when the power is turned on. 3 6 (eject) button 4 9 (lower side play)/ ( (upper side play) butt

14、on 5 p (stop) button 6 P (pause) button 7 0/) (fast forward, fast backward/AMS) button 8 r REC (recording) button 9 DIRECTION switch ! DOLBY NR (Dolby Noise Reduction) switch ! CD SYNC (CD synchro) button This button allows CD synchro recording to be executed as this set is interlocked with the DHC-

15、MD515. 4 SECTION 2 TEST MODE 2-1. CHECKING THE ITEMS OF TEST MODE The set allows you to check the items of the test mode although this may not be directly related with the adjustment. 1 Setting/Releasing the Test Mode: 1) Setting With power OFF, short between test pin 1 and pin 2 of CN09 on the LOW-

16、VOLTAGE board. (See page 15.) Then, turn power ON to enter the test mode. 2) Releasing Open between pin 1 and pin 2 of CN09. 2 Items of Test Mode 1) Memory Stop 1-1) In side A record mode, press the REW ( 0 ) button. The tape is rewind to the start point of recording and stopped. 1-2) In side B reco

17、rd mode, press the FF ( ) ) button. The tape is rewind to the start point of recording and stopped. 2) Memory Play 2-1) In side A record mode, press the FWD Auto Play ( ” + 0 ) buttons simultaneously. The tape is rewind to the start point of recording and FWD played. 2-2) In side B record mode, pres

18、s the REV Auto Play ( “ + ) ) buttons simultaneously. The tape is rewind to the start point of recording and REV played. 3) All LED Flickering When no tape is inserted, all LED indicators are flickering. 4) Aging Operation When tape with record erase preventing claw is inserted for both sides A and

19、B, enter the aging operation start command by pressing p and CD SYNC simultaneously. The system will change the direction to one side and perform the following operations: 1 Rewind in REW mode until side A of tape is stopped. 2 Playback tape in FWD mode for 1 minute. 3 Pause mode. 4 Record tape for

20、3 minutes. 5 Forward tape in FF mode to the end of side A of tape. 6 Shut off and switch to side B. 7 Playback tape in REV mode for 1 minute. 8 Pause mode. 9 Record tape for 3 minutes. ! Forward tape in FF mode to the end of side B of tape. ! Shut off and switch to side A. ! Repeat the procedure fro

21、m 2 to !. ! Pressing the STOP ( p ) button will release the set from these operations. 5 SECTION 3 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 3-1. TOP COVER 3-2. FRONT PANEL ASSY 1 screws (case 3 TP2) 3 top cover 2 screws (case 3 TP2) 1 CN6 2 BVTT 3x8 3 claw 4

22、claw 5 front panel assy 6 3-3. FRONT BOARD (TC-TX313) 3-4. PANEL BOARD (TC-TX515) 3 BVTP 2.6x8 1 BVTP 2.6x8 4 BVTP 2.6x8 5 PANEL board 2 LED board 8 PLAY button 6 POWER button 9 lens (D) ! lens (C) 7 lens (C) 1 BVTP 2.6x8 2 BVTP 2.6x8 3 BVTP 2.6x8 4 FRONT board 6 REC button 5 PLAY button 7 EJECT but

23、ton 8 POWER button 7 3-5. BACK PLATE 3-6. BRACKET (POWER TRANS) 4 BVTP 3x8 5 claws 2 BVTP 3x10 3 BVTP 3x8 1 CN04 6 back plate 5 bind type (A) 6 bracket (power trans) 2 CN14 1 CN7 4 DECK board 3 BVTP 3x8 8 3-7. MAIN BOARD 3-8. TCM ASSY 6 BVTP 3x8 5 BVTP 3x8 3 BVTP 3x10 4 BVTP 3x8 2 REC board 1 PC boa

24、rd holders 7 MAIN board 2 BVTP 3x10 1 BVTP 3x10 3 TCM assy 9 3-9. LEVER 3-10. TENSION SPRING 3 BVTP 3x8 1 BVTP 3x8 4 tape guide (R) 2 tape guide (L) 6 Turn the loading motor and down the cassette holder. 5 9 8 7 1 2 10 3-11. HOUSING 3-12. CHASSIS 3 4 2 1 4 belt (B) 5 belt (A) 3 1 2 6 7 8 9 11 3-13.

25、MOTOR (A)/(B) ASSY 3-14. HEAD PLATE 4 motor (B) assy 2 motor (A) assy 1 3 A 3 1 B 2 Note : On install, set the portions A and B. 12 3-15. PINCH ROLLER ASSY 3-16. BRACKET (HEAD UNIT) 3 bracket (head unit) 2 1 2 4 5 3 pinch roller assy (R) 6 pinch roller assy (F) 1 13 PRECAUTION 1.Clean the following

26、parts with a denatured-alcohol-moistened swab : record/playback/erase headpinch roller rubber beltscapstan idlers 2.Demagnetize the record/playback/erase head with a head demagnetizer. (Do not bring the head demagnetizer close to the erase head.) 3.Do not use a magnetized screwdriver for the adjustm

27、ents. 4.After the adjustments, apply suitable locking compound to the parts adjusted. 5.The adjustments should be performed with the rated power supply voltage unless otherwise noted. Torque Measurement ModeTorque MeterMeter Reading 35 80 g cm FWD CQ-102C (0.49 1.11 oz inch) FWD1 7 g cm Back tension

28、(0.012 0.097 oz inch) 35 80 g cm REV CQ-102RC (0.49 1.11 oz inch) REV1 7 g cm Back tension(0.012 0.097 oz inch) more than 40 g cm FF, REWCQ-201B (more than 0.56 oz inch) SECTION 5 ELECTRICAL ADJUSTMENTS SECTION 4 MECHANICAL ADJUSTMENTS PRECAUTION 1.The adjustment should be performed in the publicati

29、on. (Be sure to male playback adjustment at first.) 2.The adjustments and measurement should be performed for both L-CH and R-CH. Switch position DOLBY NR switch : OFF DIRECTION switch : A Standard Input Level Input terminalTAPE IN source impedance10 k input signal level0.49 V ( 4 dB) Standard Outpu

30、t Level Output terminalTAPE OUT (L-CH) load impedance47 k output signal level0.49 V ( 4 dB) Test Tape TypeSignalUsed for P-4-A10010 kHz, 10 dBAzimuth Adjustment P-4-L300315 Hz, 0 dBPB Level Adjustment WS-48A3 kHz, 0 dBTape Speed Adjustment 0 dB = 0.775 V 14 TAPE IN 315 Hz, 0.49 V ( 4 dB) TAPE IN 1)

31、315 Hz 2) 10 kHz 43.6 mV ( 25 dB) TAPE OUT Record Bias Adjustment Setting : Set to the TEST mode. (See page 4.) Procedure : 1.Mode: Record speed checker or frequency counter 47 k set test tape WS-48A (3 kHz, 0 dB) Tape Speed Adjustment Procedure : 1.Mode: FWD playback Adjustment Limits : normal spee

32、d Speed checkerFrequency counter 3 to + 3 %2,910 to 3,090 Hz Confirm that the deviation between tape top and tape end is within 3%. Adjustment Location : Capstan motor volume (See page 15.) Sample Value of Wow and flutter W. RMS (JIS) within 0.3% (test tape : WS-48A) Playback Level Adjustment Proced

33、ure : 1.Mode: FWD playback 2.Adjust SFR03 (L-CH) and SFR04 (R-CH) on MAIN board so that the reading on level meter meets the adjustment limits below. Adjustment Limits : TAPE OUT level Level difference between channels 4 2 dB (0.39 to 0.62 V)within 2 dB Check that the TAPE OUT level does not change

34、even if Playback and Stop operation is repeated several times. Adjustment Location : MAIN board (See page 15.) TAPE OUT level meter 47 k set test tape P-4-L300 (315 Hz, 0 dB) 2.Mode: Playback 3.Confirm playback the signal recorded in step 1 become adjustment level as follows. 4.If these levels do no

35、t adjustment level, adjust SFR01 (L-CH) and SFR02 (R-CH) on REC board to repeat step 1 and 2. Adjustment Level :Difference of playback output of 10 kHz to playback output of 315 Hz : 0 0.5 dB Adjustment Location : REC board (See page 15.) Record Level Adjustment Setting : Set to the TEST mode. (See

36、page 4.) Procedure : 1.Mode: Record 2.Mode: Playback 3.Confirm playback the signal recorded in step 1 become adjustment level as follows. 4.If these levels do not adjustment level, adjust SFR11 (L-CH) and SFR12 (R-CH) on REC board to repeat step 1 and 2. Adjustment Level :Playback output level of 31

37、5 Hz : 4 2 dB (0.39 to 0.62 V) Adjustment Location : REC board (See page 15.) TAPE OUT TAPE OUT level meter 47 k set recorded portion AF OSC attenuator 10 k set 600 blank tape CS-123 AF OSC attenuator 10 k set 600 blank tape CS-123 level meter 47 k set recorded portion 15 IC02 CN03 CN11 CN03 CN10 CN

38、05 SFR04 PLAYBACK LEVEL ADJ (R-CH) SFR03 PLAYBACK LEVEL ADJ (L-CH) SFR11 RECORD LEVEL ADJ (L-CH) SFR12 RECORD LEVEL ADJ (R-CH) M1 CAPSTAN /REEL MOTOR CN09 TEST MODE TAPE SPEED ADJ M2 LOADING MOTOR MECHANISM DECK SFR02 RECORD BIAS ADJ (R-CH) SFR01 RECORD BIAS ADJ (L-CH) Adjustment Location : MAIN boa

39、rd (component side) LOW-VOLTAGE board (component side) REC board (component side) 16 SECTION 6 DIAGRAMS 6-1. CIRCUIT BOARDS LOCATION TC-TX313 TRANSFORMER board SLIDE SW board (Singapore, Malaysia, Hong Kong model) LOW-VOLTAGE board AMS board REC board MAIN board MOTOR board FRONT board DECK board PO

40、WER board TRANSFORMER board LOW-VOLTAGE board AMS board REC board MAIN board MOTOR board LED board PANEL board DECK board POWER board SLIDE SW board (Singapore, Malaysia, Hong Kong model) TC-TX515 31 6-8. IC PIN DESCRIPTION IC04 PD75108GF-N14-3BE (SYSTEM CONTROL) Pin No.Pin NameI/OPin Description 1R

41、VS REC RELAYORVS REC relay control output (Not used in this set.) 2FWD REC RELAYOFWD REC relay control output (Not used in this set.) 3RVS PLAY RELAYORVS PLAY relay control output (Not used in this set.) 4FWD PLAY RELAYOFWD PLAY relay control output (Not used in this set.) 5POWER OUTOPower output (N

42、ot used in this set.) 6AMS OUTOAMS gain control output (Not used in this set.) 7RESETIReset input (L : Reset) 8XTALOscillator circuit (4.19 MHz) 9XTALOscillator circuit (4.19 MHz) 10NR OUTONoise reduction signal output (Not used in this set.) 11REC/PBOREC/PB select output (H : REC, L : PB) 12F/RORVS

43、/FWD select output (H : RVS, L : FWD) (Not used in this set.) 13BIASOBias oscillation control output (H : ON, L : OFF) 14LINE MUTEOLine mute control output (H : OFF, L : ON) 15PB.MUTEOPB mute control output (H : OFF, L : ON) 16REC.MUTEOREC mute control output (H : OFF, L : ON) 17TAPE 4OREC equalizer select output (H : METAL) (Not used in this set.) 18TAPE 2OREC equalizer select output (H