Sony-TC-S9-Service-Manual电路原理图.pdf

上传人:cc518 文档编号:86541 上传时间:2020-10-10 格式:PDF 页数:30 大小:2.74MB
下载 相关 举报
Sony-TC-S9-Service-Manual电路原理图.pdf_第1页
第1页 / 共30页
Sony-TC-S9-Service-Manual电路原理图.pdf_第2页
第2页 / 共30页
Sony-TC-S9-Service-Manual电路原理图.pdf_第3页
第3页 / 共30页
亲,该文档总共30页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

《Sony-TC-S9-Service-Manual电路原理图.pdf》由会员分享,可在线阅读,更多相关《Sony-TC-S9-Service-Manual电路原理图.pdf(30页珍藏版)》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL STEREO CASSETTE DECK AEP Model UK Model E Model Australian Model SPECIFICATIONS TC-S9 Ver 1.0 2001.09 9-873-281-01Sony Corporation 2001I0500-1Home Audio Company C 2001.9Shinagawa Tec Service Manual Production Group TC-S9 is the Tape deck section in MHC-S9D. Tape deck Model Name Using

2、Similar MechanismTC-S3 SectionTape Transport Mechanism Type TCM-230AWR41, TCM-230MWR41 Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double-D symbol ; are trade- marks of Do by Laboratories Licensing Corporation. Recording system4-tra

3、ck 2-channel stereo Frequency response60 13,000 Hz (3 dB), (DOLBY NR OFF)using Sony TYPE I cassette, 60 14,000 Hz (3 dB), using Sony TYPE II cassette Dimensions (w/h/d)Approx 280 x 128 x 330 mm MassApprox 2 4 kg Design and specifications are subject to change without notice RadioFans.CN 收音机爱 好者资料库 2

4、 TC-S9 TABLE OF CONTENTS 1.SERVICING NOTES.3 2.GENERAL Location of Controls .4 3.DISASSEMBLY 3-1.Disassembly Flow .5 3-2.Case .5 3-3.MAIN Board .6 3-4.Front Panel Section .6 3-5.Tape Mechanism Deck (TCM-230AWR41, TCM-230MWR41).7 3-6.LEAF SW Board, HEAD (A) Board and HEAD (B) Board .7 4.TEST MODE.8 5

5、.MECHANICAL ADJUSTMENTS.9 6.ELECTRICAL ADJUSTMENTS.9 7.DIAGRAMS 7-1.Note for Printed Wiring Boards and Schematic Diagrams . 13 7-2.Schematic Diagram MAIN Section (1/2) . 14 7-3.Schematic Diagram MAIN Section (2/2) . 15 7-4.Printed Wirings Boards MAIN Section . 16 7-5.Schematic Diagram LEAF SW Sectio

6、n . 17 7-6.Printed Wiring Board LEAF SW Section . 17 7-7.Schematic Diagram PANEL Section . 18 7-8.Printed Wiring Boards PANEL Section . 18 7-9.IC Pin Function Description . 19 8.EXPLODED VIEWS 8-1.General Section . 21 8-2.Front Panel Section . 22 8-3.Tape Mechanism Deck Section (TCM-230AWR41). 23 8-

7、4.Tape Mechanism Deck Section (TCM-230MWR41) . 24 8-5.Sub Chassis Assy Section (TCM-230MWR41) . 25 9.ELECTRICAL PARTS LIST. 26 Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. SAFETY-RELATED CO

8、MPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY. RadioFans.CN 收

9、音机爱 好者资料库 3 TC-S9 SECTION 1 SERVICING NOTES ModelPART No. AEP and UK models4-236-839-0 Australian, Saudi Arabia and Korean models 4-236-839-1 E and Singapore models4-236-839-2 Mexican model4-236-839-3 Thai model4-236-839-4 MODEL IDENTIFICATION Rear Panel This set is a component of the MHC-S9D. The M

10、HC-S9D system configuration is as shown below, and there- fore it does not operate normally unless all four components are connected. In performing the repair, connect all components with the system cables. Note: The precaution to the users is described on the label stuck on the back panel (DVD/vide

11、o CD/CD player) and in the trouble- shooting section in the Operation Manual. System Configuration: POWER SUPPLY AC IN TA MASTER (45, 46, 55) Deck A N (forward play) tk (44, 55, 63) n (reverse play) tj (44, 63) x (stop) th (44) /M (go forward/fast forward) y; (44) ./m (go back/rewind) tl (44) Z (eje

12、ct) tg (44, 63) Deck B N (forward play) rh (44, 45, 63) n (reverse play) rj (44, 45, 63) x (stop) rk (44, 45, 55) M/ (fast forward/go forward) rf (44) m/. (rewind/go back) rg (44) Z (eject) rl (44, 63) hHAUTO REVERSEhHAUTO REVERSE . h H . h x AA y; tl tk tj th tg rf rg rh rj rk rl t;tatstdtf Main un

13、it Parts Identification The items are arranged in alphabetical order. Refer to the pages indicated in parentheses ( ) for details. Remote control ANGLE es (37) AUDIO ws (34) CLEAR qs (22, 29, 30, 36) CLOCK/TIMER SELECT 3 (47, 56) CLOCK/TIMER SET 2 (17, 47, 56) DBFB ra (48) D.SKIP 9 (26) DIGITAL rf (

14、57) DISPLAY rj (17, 31, 32, 43, 54) DVD DISPLAY wd (18, 19, 30, 3234, 3640) DVD MENU wa (27) DVD SET UP ql (18, 19, 24, 39) ENTER wj EQ ea (52) EQ ON/OFF wl (53) FILE SELECT +/ wh (48, 49, 53) FUNCTION rd (18, 25, 27, 28, 36, 45, 46, 55, 57) GROOVE rs (48) KARAOKE PON (Except for European model) el

15、(54) MD rh (57) Numeric buttons 8 (28, 30) PLAY MODE qa (25, 28, 29, 46) REPEAT q; (30) RETURN O qd (27, 39, 40) SELECT DVD N eh (20, 25, 27, 29, 30) SET UP wf (14, 16, 51, 53, 54) SLEEP 1 (55) SLOW t/T qk (26) SPECTRUM ANALYZER rk (54) STEP c/C ef (26) SUBTITLE ed (37) SUR e; (51) TAPE A nN ek (44)

16、 TAPE B nN qf (44, 45) TITLE w; (27) TUNER/BAND ej (42) TV /1 4 (13) TV CH +/ 7 (13) TV/VIDEO rl (13) TV VOL +/ 6 (13) VIDEO rg (57) VOL +/ wg Mm. nNO TtCc V v Bb 1 234 5 e; es ef ej eg 6 7 9 8 q; qa qdqs qfqg qj qh qkql wa wd ws wf w; wg wj wh wk ed wl ea eh el rs ra rd ek r; rg rj rl rf rh rk BUTT

17、ON DESCRIPTIONS /1 (power) 5 X (pause) qj x (stop) qg m/M (rewind/fast forward), TUNING /+ qh ./ (go back/go forward), PRESET /+, PREV/NEXT eg O/o/P/p wk 10 r; TC-S9 5 This set can be disassembled in the order shown below. 3-1.DISASSEMBLY FLOW SECTION 3 DISASSEMBLY Note: Follow the disassembly proce

18、dure in the numerical order given. 3-2.CASE 3-2.CASE (Page 5) 3-3.MAIN BOARD (Page 6) 3-4.FRONT PANEL SECTION (Page 6) 3-6.LEAF SW BOARD, HEAD (A) BOARD AND HEAD (B) BOARD (Page 7) 3-5.TAPE MECHANISM DECK (TCM-230AWR41, TCM-230MWR41) (Page 7) SET 2two screws (case 3 TP2) 3 3 2two screws (case 3 TP2)

19、 1three screws (BVTT3 6) 4Remove the case in the direction of arrow A. A TC-S9 6 3-3.MAIN BOARD 3-4.FRONT PANEL SECTION 2connector (CN1) 5MAIN board 1wire (flat type) (17 core) (CN311) 2three connectors (CN309, 310, 314) 3three screws (BVTP3 8) 3screw (BVTP3 8) 4PC board holder 2connector (CN2) 7fro

20、nt panel section 2connector (CN1) 3screw (BVTP3 8) 2connector (CN314) 1wire (flat type) (17 core) (CN311) 4lug 6two claws 2connector (CN2) 6three claws 5three screws (BVTP3 8) TC-S9 7 3-5.TAPE MECHANISM DECK (TCM-230AWR41, TCM-230MWR41) 2five screws (BVTP2.6 8) 4tape mechanism deck (TCM-230AWR41, TC

21、M-230MWR41) 1Open the cassette holder (L)/(R). 3lug 3-6.LEAF SW BOARD, HEAD (A) BOARD AND HEAD (B) BOARD 6screw (+PTT 2 4) 4screw (+PTT 2 4) 3LEAF SW board 2five claws 5head (A) board 7head (B) board 1Remove the four solderings. 8 TC-S9 SECTION 4 TEST MODE Note: Use following buttons in the test mod

22、e. no mark: Button of Tape unit (TC-S9) *1: Button of amplifier unit (TA-S9D) *2: Button of DVD/video CD/CD unit (DVP-S9) MC Test Mode Enter the MC Test Mode Procedure: 1.Press the I/1 *1 button to turn the power on. 2.While pressing the both PLAY MODE*2 and *2 buttons, press the DISC 3*2 button. 3.

23、“GROOVE” indication blinks on the fluorescent indicator tube in the midst of MC test mode. Releasing the MC Test Mode To release from this mode, press the I/1 *1 button or disconnect the power cord. DECK Test Mode In the DECK test mode, it operates as follows. Cancellation of the linear mute of DOLB

24、Y IC (IC301) It become cancellation automatically when it is possible to en- ter a MC test mode. AMS Checking Procedure: 1.Enter the MC test mode. 2.Insert a test tape AMS-110A or AMS-120 to Deck A. 3.Set TAPE A function. 4.Press the DVD SYNC button to enter the AMS test mode. 5.After a tape is rewo

25、und first, the FF AMS is checked, and the mechanism is shut off after detecting the ASM signal twice. 6.Then the REW AMS is checked and the mechanism is shut off after detecting the AMS signal twice. 7.When the check is complete, a message of either OK or NG appears. (To check an AMS of the B deck,

26、select TAPE B function. After that, press DVD SYNC.) x ALC Checking Procedure: 1.Enter the MC test mode. 2.Insert a tape into Deck B. 3.During Recording, Keep holding down the below keys. *2 + REC PAUSE/START ALC could keep ON while these keys keep being pressed, ALC could keep OFF while keys are re

27、leased. Double Speed REC Mode Procedure: 1.Enter the MC test mode 2.Insert a tape into Deck B. 3.During Recording, keep holding down the below key. HI-DUB Double speed recording is going on while the key keeps being pressed. REC/PLAY Checking The mode to PLAY by rewinding recording contents automati

28、- cally. Procedure: 1.If recording A surface, it returns automatically at the point of the recording beginning and it replays when pressing TAPE B . 2.If recording B surface, it returns automatically at the point of the recording beginning and it replays when pressing TAPE B . x M m 9 TC-S9 SECTION

29、5 MECHANICAL ADJUSTMENTS SECTION 6 ELECTRICAL ADJUSTMENTS 0 dB=0.775 VDECK SECTION 1.Demagnetize the record/playback head with a head demagnetizer. 2.Do not use a magnetized screwdriver for the adjustments. 3.After the adjustments, apply suitable locking compound to the parts adjust. 4.The adjustmen

30、ts should be performed with the rated power supply voltage unless otherwise noted. 5.The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit ad- justment should be completed before performing recording circuit adjustment.) 6.The adjustments

31、 should be performed for both L-CH and R- CH. 7.Switches and controls should be set as follows unless other- wise specified. 8.Please refer to “SERVICING NOTES” (page 3) before adjust- ments. Test Tape TapeSignalUsed for P-4-A10010 kHz, 10 dBAzimuth Adjustment WS-48B3 kHz, 0 dBTape Speed Adjustment

32、P-4-L300J315 Hz, 0 dBLevel Adjustment DECK A DECK B Record/Playback Head Azimuth Adjustment Note: Perform this adjustments for both decks Procedure: 1.Mode: Playback Precaution 1.Clean the following parts with a denatured alcohol-moistened swab: record/playback headspinch rollers erase headrubber be

33、lts capstanidlers 2.Demagnetize the record/playback head with a head demagne- tizer. 3.Do not use a magnetized screwdriver for the adjustments. 4.After the adjustments, apply suitable locking compound to the parts adjusted. 5.The adjustments should be performed with the rated power supply voltage un

34、less otherwise noted. Torque Measurement set ST-S9 test tape P-4-A100 (10 kHz, 10 dB) + level meter MD OUT jack (J601) 3.06 N m to 6.96 N m 31 to 71 g cm (0.43 0.98 oz inch) 0.19 N m to 0.58 N m 2 to 6 g cm (0.02 0.08 oz inch) 3.06 N m to 6.96 N m 31 to 71 g cm (0.43 0.98 oz inch) 0.19 N m to 0.58 N

35、 m 2 to 6 g cm (0.02 0.08 oz inch) 6.96 N m to 14.02 N m 71 to 143 g cm (0.98 1.99 oz inch) 9.80 N m 100 g or more (3.53 oz or more) 9.80 N m 100 g or more (3.53 oz or more) ModeTorque meter CQ-102C CQ-102C CQ-102RC CQ-102RC CQ-201B CQ-403A CQ-403R Meter reading FWD FWD back tension REV REV back ten

36、sion FF/REW FWD tension REV tension 10 TC-S9 2.Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak. 3.Mode: Playback 4.After the adjustments, apply suitable locking compound to the pats adju

37、sted. Adjustment Location:Playback Head (Deck A). Record/Playback/Erase Head (Deck B). Note: Use following buttons in the test mode. no mark: Button of Tape unit (TC-S9) *1: Button of amplifier unit (TA-S9D) *2: Button of DVD/video CD/CD unit (DVP-S9) Tape Speed AdjustmentDECK B Note: Start the Tape

38、 Speed adjustment as below after setting to the test mode. In the test mode, the tape speed is high during pressing the HI-DUB button. Procedure: 1.Turn the power switch on. 2.While pressing the both PLAY MODE*2 and *2 buttons, press the DISC 3*2 button. (The “GROOVE” on the fluorescent indicator tu

39、be display while in the test mode.) To exit from the test mode, press the?/1 *1 button. Mode: Playback 1.Insert the WS-48B into the deck B. 2.Press the N button on the deck B. 3.Press the HI-DUB button in playback mode. Then at HIGH speed mode. 4.Adjust RV1001 on the LEAF SW board so that frequency

40、counter reads 6,000 180 Hz. 5.Press the HI-DUB button. Then back to NORMAL speed mode. 6.Adjust RV1002 on the LEAF SW board so that frequency counter reads 3,000 90 Hz. Adjustment Location: LEAF SW board Sample Volue of Wow and Flutter: 0.3% or less W. RMS (WS-48B) Playback Level AdjustmentDECK A DE

41、CK B Procedure: Mode: Playback 1.Confirm that level difference between the channels is with 0.5 dB. 2.After check, adjust the following RVs. Deck A is RV302 (L-CH), Deck B is RV303 (L-CH) so that adjustment within adjustment level as follows. Adjustment Level: MD OUT jack (J601) PB level: 334.4 to 7

42、48.7 mV (6.8 0.5 dB) Adjustment Location: MAIN board Screw position L-CH peak within 1dB Output level L-CH peak R-CH peak within 1dB Screw position R-CH peak set test tape P-4-A100 (10 kHz, 10 dB) oscilloscope L-CH R-CH waveform of oscilloscope in phase 4590135 180 goodwrong ST-S9 MD OUT jack (J601)

43、 + + set test tape WS-48B (3 kHz, 0 dB) frequency counter ST-S9 MD OUT jack (J601) set test tape P-4-L300J (315 Hz, 0 dB) ST-S9 + level meter MD OUT jack (J601) reverse forward x 11 TC-S9 Adjustable level: MD OUT jack PB level: 47.2 to 53.0 mV (27.3 to 26.3 dB) Adjustment Location: MAIN board MAIN B

44、OARD (Component Side) LEAF SW BOARD (Component Side) REC Bias Adjustment DECK B Procedure: 1.Insert a tape into Deck B. 2.After press REC PAUSE/START button, press REC PAUSE/START button, then recording start. 3.Mode: Record 4.Mode: Playback 5.Confirm the playback signal recorded in step 3 becomes a

45、d- justable level as follows. If these levels are not adjustable level, adjust the RV304 (L- CH) and RV354 (R-CH) on the MAIN board to repeat steps 4 and 5. Adjustable level: Playback output of 315 Hz to playback output of 10 kHz: 1.0 dB Adjustment Location: MAIN board REC Level Adjustment DECK B Pr

46、ocedure: 1.Insert a tape into Deck B. 2.After press REC PAUSE/START button, press REC PAUSE/START button, then recording start. 3.Mode: Record 4.Mode: Playback 5.Confirm the play back signal recorded in step 3 becomes ad- justable level as follows. If these levels are not adjustable level, adjust the RV301 (L- CH) and RV35

展开阅读全文
相关资源
猜你喜欢
相关搜索
资源标签

当前位置:首页 > 卡座/开盘/组合/收录机 > Sony

copyright@ 2008-2023 收音机爱好者资料库 版权所有
备案编号:鄂ICP备16009402-5号