Tascam-DR-100-Service-Manual电路原理图.pdf

《Tascam-DR-100-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Tascam-DR-100-Service-Manual电路原理图.pdf（43页珍藏版）》请在收音机爱好者资料库上搜索。

1、DR-100 Portable Digital Recorder Effective : May, 2009S-0187 CONTENTS 1.Specifications 3 2.Test Mode 5 3.Updating of System Firmware 10 4.Message Display glossary 13 5.Block Diagram 18 6.Level Diagram 20 7.Exploded Views and Parts List 27 8. Notes for Disassembly / Assembly 30 9.PC Boards and Parts

2、List 32 10. Included Accessories 43 目次 1.仕様 3 2. 5 3.System F/W 10 4.一覧 13 5. 18 6. 20 7.分解図 27 8.分解組立上注意 30 9.基板図 32 10. 付属品 43 RadioFans.CN 收音机爱 好者资料库 2 1. Specifications 仕様 TASCAM DR-100 Audio input ratings XLR MIC IN (L, R) inputs Connectors: XLR-3-32equivalent (balanced) Input impedance: 1.2 k

3、GAIN HIGH setting Standard input level: -58 dBu Maximum input level: -42 dBu GAIN MID setting Standard input level: -36 dBu Maximum input level: -20 dBu GAIN LOW setting Standard input level: -14 dBu Maximum input level: +2 dBu LINE IN input Connector: 3.5 mm stereo minijack Input impedance: 23 k St

4、andard input level: -10 dBV Maximum input level: +6 dBV LINE OUT output Connector: 3.5 mm stereo minijack Standard output level: -10 dBV Maximum output level: +6 dBV output Connector: 3.5 mm stereo minijack Maximum output : 25 mW + 25 mW (with 32 headphone connection) Built-in speakers Output: 0.4 W

5、 Audio performance Frequency response (LINE IN LINE OUT): 20 Hz20 kHz, +1/-3 dB (44.1 kHz) 20 Hz22 kHz, +1/-3 dB (48 kHz) Distortion (LINE IN LINE OUT): Less than 0.01% S/N ratio (LINE IN LINE OUT): 90 dB or more Compatible audio files: MP3 files: 32320 kbps, sampling frequency 44.1/48 kHz, VBR play

6、back, ID3 tag support up to Ver 2.4 入出力定格 XLR MIC IN（L/R）入力 端子：XLR-3-32相当（） 入力：1.2k GAIN HIGH時 基準入力：58dBu 最大入力：42dBu GAIN MID時 基準入力：36dBu 最大入力：20dBu GAIN LOW時 基準入力：14dBu 最大入力：2dBu LINE IN入力 端子：3.5mm 入力：23k 基準入力：10dBV 最大入力：6dBV LINE OUT出力 端子：3.5mm 基準出力：10dBV 最大出力：6dBV 出力 端子：3.5mm 最大出力：25mW + 25mW （32

7、 接続時） 内蔵 出力：0.4W 性能 周波数特性（LINE IN LINE OUT)： 20Hz20kHz、1/3dB（44.1kHz） 20Hz22kHz、1/3dB（48kHz） 歪率（LINE IN LINE OUT)： 0.01% 以下 S/N比（LINE IN LINE OUT)： 90dB以上 一般 対応音声： MP3：32kbps320kbps、 周波数44.1kHz/48kHz、 VBR再生対応、ID3（Ver12.4） RadioFans.CN 收音机爱 好者资料库 3 TASCAM DR-100 WAV files: sampling frequency 44.1/48

8、kHz, bit length: 16/24-bit Recording media:SD cards (64 MB2 GB) and SDHC cards (4 GB32 GB) File system: FAT partition:FAT16/32 Battery life (continuous operation): Lithium ion battery (BP-L2): About 5 hours (recording time) About 5 hours (playback time) Ni-MH batteries (HR15/51): About 4 hours (reco

9、rding time) About 4 hours (playback time) Alkaline batteries (LR6): About 2 hours (recording time) About 2 hours (playback time) (Backlight off, set to 128-kbps mp3.Varies according to use conditions.) Operation temperature range: 040 C Power consumption: 1.7 W (MP3 playback) 5.5 W (maximum) Externa

10、l dimensions (mm): 80 (w) x 153 (h) x 35 (d) (excluding protrusions) Weight:290 g (not including batteries) Accessory (sold separately) AC adapter:PS-P520 Requirements for connected computers Windows:Pentium 300 MHz or better 128 MB or more memory USB port (USB 2.0 recommended) Macintosh:266 MHz Pow

11、er PC, iMac, G3, G4 or better 64MB or more memory USB port (USB 2.0 recommended) Recommended USB host controller: Intel chipset Supported OS: Windows: Windows 2000 Professional SP4 or newer,Windows XP, Windows Vista Macintosh: Mac OS X 10.2 or newer WAV：周波数44.1kHz/48kHz 長：16/24 記録媒体：SD（64M2G） SDHC（4

12、G 32G） ： FAT： FAT16/32 電池持続時間（連続動作時）： 専用充電池（BP-L2）使用時： 約5時間（JEITA 録音時間） 約5時間（JEITA 音楽再生時間） 水素電池使用時： 約4時間（JEITA 録音時間） 約4時間（JEITA 音楽再生時間） 乾電池使用時： 約2時間（JEITA 録音時間） 約2時間（JEITA 音楽再生時間） （消灯、MP3 128kbps 時。使用状況 変動。 ） 使用温度範囲：040 消費電力：1.7W（MP3再生時） 5.5W（最大） 外形寸法：80（幅）153（高）35（奥行） mm（突起部含） 質量：290g（電池含） 別売 AC：PS

13、-P520 接続条件 Windows：Pentium 300MHz以上 128MB以上Memory USB （推奨：USB2.0） Macintosh：Power PC、iMac、G3、G4 266MHz以上 64MB以上Memory USB （推奨：USB2.0） 推奨USB： Intel 製 OS： Windows：Windows 2000 Professional SP4以上 / XP / Vista Macintosh：Mac OS X 10.2以上 4 TASCAM DR-100 Dimensional drawing(寸法図） DATA encoder (0-999) Shows

14、the name of a key pressed Power supply voltage (255 steps) Li shown when powered on Li-Ion battery; AA shown when powered on AA battery; shown when connected to an AC outlet. Read in input volume value USB connection Card detection When card protecting SW is turned on, the key mark is displayed. Ope

15、ration indicator Event acceptance indicator. This indicator reacts when keys are operated for example 5 2. Test Mode TASCAM DR-100 1. How to enter test mode While holding down the HOME+MENU+ENTER keys, switch the power on. The LCD shows the following message:The LCD back- light is lit. 1. 起動方法 HOME+

16、MENU+ENTER押電源投入 。 LCD下記表示。点灯。 2. 画面説明 DATA（0999） 押表示。 電源供給電圧（255段階） Li：Li-IonAA：単三電池 AC接続時： 入力Volume L/R読取値 USB接続 検出 SWON 鍵表示。 動作 受付。 操作反応。 3. LED REC LED：REC点灯。 PEAK LED：PLAY/PAUSE点灯。 全長押点滅。 4. MENU MENU押下記表示。 操作項目移動。 ENTER： 項目選択。 MENU：TOP画面。 2. Displays explained 3. Checking LEDs REC LED: turns on

17、 when the REC key is pressed. PEAK LED: turns on when the PLAY/PAUSE key is pressed. They turn off when the keys are held pressed for a certain time. 4. Menu Pressing the MENU key reveals the following menu. Options are selectable using the encoder. ENTER:mode selection MENU: back to the TOP screen

18、6 TASCAM DR-100 2) CARD Selecting CARD and pressing the ENTER key gets you to the following menu: 2)CARD CARD 選択ENTER押下記表示 。 Identify： 情報読込 ENTER押下記情報表示。 Identify: Read in data Pressing the ENTER key indicates the following informa- tion: 1)INPUT INPUT 選択ENTER押下記表 示。 入力SW MIC GAIN SW SW 電源SW SW SW 1

19、) INPUT Selecting INPUT and pressing the ENTER key gets you to the following menu: INPUT Select SW MIC GAIN SW Limiter SW Phantom Power SW Speaker Sw Headphone Jack SW Manufacturer ID OEM/Application ID Product name Product revision Product serial number Manufacturing date Raw Size Manufacturer ID O

20、EM/Application ID Product name Product revision Product serial number Manufacturing date Raw Size Read One：1読込 押、押1毎 読込行。 Read One: Read in data from the card per sector At each press of the key, data is read in from the card per sector. 7 TASCAM DR-100 Format: Card formatting At a press of the REC

21、key, the following screen appears: Format： REC押下記画面表示。 If ENTER key is pressed at this screen, the card starts being formatted. Upon completion of the formatting process, Complete is displayed. Pressing MENU brings you back to the top screen. 3) USB Check Select USB and press the ENTER key. Each tim

22、e the ENTER key is pressed, the indication alter- nates between ON and OFF. ENTER 押Format実行、実行後、 Complete表示終了。 MENUTop画面戻。 3) USB Check USB選択ENTER押。 ENTER押ON/OFF繰返。 USB Chek USB OF ENER - ON 4) LCD Check LCD選択ENTER押下記画面表示。 4) LCD Check Select LCD and press ENTER key and the following are displayed:

23、調整 IO：LOOP： 調整傾 (：) 残像確認用 STOP/HOME：反転 Contrast adjustment (IO: +; LOP: -) adjustment (: +; : -) Characters for after- image check STOP/HOME key : Reverse 5) RTC Check RTC選択ENTER押下記画面表示。 表示(日時表示)。 5) RTC Check Select RTC and press ENTER key and the following are displayed: Real-time clock indication

24、.(Date and time indication only) C C heck IME: 2 2 50 DAE: 00 0 0 000 時刻. 日付（年月日） 年2000年00表 示 Time Date (yy/mm/dd) The year of 2000 is indicated as 00. Function start Function cease Receive key, Status Command Firmware version of Remote control MCU Error Timeout ：Time Out Unkown Res： Illegal respons

25、e Unkown Key：Undefined key code Rx Error ：Receive error System ：System error Version ：Inconsistent version CustomCode： Inconsistent custom code Unkown ：Unknown error 8 TASCAM DR-100 6) EEPROM Check EEPROM選択ENTER押下記画面表示 。 6) EEPROM Check Select EEPROM and press ENTER key and the following are display

26、ed: EPROM Che READ : ENER WRIE : REC ROM読込実行。 ENTER Reading. 表示。 ROM書込。 Are you sure ?後ENTER 書込。 MENU。 Read in from the ROM Reading. is displayed at a press of the ENTER key. Writing all zeros to the ROM The writing process starts at a press of the ENTER key in response to Are you sure? To cancel th

27、e process, press the MENU key. If errors occur during either the read or the write, the following are displayed: Timeout Err:No response from the EEPROM Error:Errors at data send/receive time Verify Err:Errors in verification during the write process 7) REMOTE Check Select REMOTE and press ENTER key

28、 and the following are displayed: READ/WRITE共場合下記表示。 Timeout Err:EEPROM応答 Error:送信/受信時 Verify Err:Write時 7) REMOTE Check REMOTE選択ENTER押下記画面表示 。 動作開始 動作停止 受信、 用FW Timeout ： Unkown Res：不正 Unkown Key：未定義 Rx Error ：受信 System ： Version ：不一致 CustomCode： 不一致 Unkown ：未知 8) BG BG選択ENTER押。 背景 FWD()：後REW()：前 8

29、) BG Select BG and press ENTER key: Background samples FWD(): Previous; REW(): Next 9 TASCAM DR-100 9) VERSION Check Select VERSION and press ENTER key and the following are displayed: 9) VERSION Check VERSION選択ENTER押下記画面表示 。 名 。 後半桁番号 日付 時刻 Model Name Version of the system firmware. The last 4 digi

30、ts indicate a build number on which the system firmware was built. which the system firmware was built. 10 3. Updating of Firmware 方法 TASCAM DR-100 1.準備 1) 本体PCUSB接続。 2) 本体UTILITY置。 3) PCUSB取外 行、本体電源落 。 2.起動 ENTER+MENU押電源投入。 LCD下記表示。 1. Preparations 1) Make the connection between this unit and the P

31、C using a USB cable. 2) Place the update file in the UTILITY folder in the unit. 3) Perform the USB device remove action on the PC, and then switch off the power to the unit. 2.START-UP While holding down the PLAY and MENU keys, switch the power on. The LCD looks like this: ROGRAM UPDA DR0_ 5 0 DR0_

32、 6 .0 DR0_ 7 . 02 拡張子付表示。 時点USB接続可能。 接続通常同USB画面、USB抜 通常起動。 従、PLAY+MENU押USB抜 再画面。 3.画面説明 1) 一場合 Update files are shown with extensions. The USB connection can be made at this point. When USB connected, the normal USB screen appears. When unplugging the USB cable, the unit shifts to the normal start-u

33、p. That is to say, the update screen reappears when unplugging the USB cable while holding down the PLAY and MENU keys. 3.Displays explained 1) When only a single file is available: ROGAM UPDA DR0_ 7 . 02 2) 複数場合2) When multiple files are available: PROGRAM UPDAE R- 00_ 5 .0 R- 00_ 6 .0 R-100_ 7 . 0

34、2 When there are 6 or more files, use the dial to move the cursor over them. 以上場合移動。 11 TASCAM DR-100 3) When no update file is available: Nothing can be done. 3) 無場合 何操作。 PRGRAM UPDAE No Upda e ile 4.確認 対象選択、ENTER押。 4.File confirmation Select a target file and press the ENTER key . ROGAM PDAE DR-0_

35、17 . 02 0 0 Are you s re ? 選択名 左：現 右：新 Name of the file selected Current version at left and New version at right 5.Getting update started The update process starts when pressing the ENTER key . 5.実行 ENTER押実行。 PROGRM UPDAE R- 00_ . 02 . 0 . 0 Era ing . 0 / 3 動作状況 FLASH番号 単位書込進捗 Task progress. FLASH

36、sector number Writing progress by sector Pressing the MENU key brings you back to the file selec- tion screen, as at step 2, without performing the update. 6.Completion 実行、2.選択画面戻 MENU押。 6.完了 PROGRAM UPAE R- 007 . 02 0 / 3 Upda e Com le e Upon completion of the update process, Complete is displayed

37、and the unit automatically switched off. 完了Complete 表示自動的電 源切。 12 TASCAM DR-100 7.Error messages 1) If an error occurs when selecting a file, the following messages appear: 7. 1) 選択時発生場合 The product ID of the file does not match (the file may be for other products). ID一致（別製品可能性） 。 Product The file v

38、ersion is older than the current one. 現古。 Old Version The checksum does not match. 一致。 Checksum Error in file reading. 読込。 Update File Messages()Meaning (内容) 2) If an error occurs in the data rewriting process, the following messages appear: 2) 書換時発生場合 Error in erasing. 消去 Flash Erase Blank error as

39、 a result of data erasure. 消去後 Flash Blank Error in writing. 書込 Flash Write Error in verification after data has been written. 書込後 Flash Verify Messages()Meaning (内容) The IN and OUT points are too close together. Reset the IN and OUT points with at least 1 sec- ond between them. IN点OUT点間隔短。1秒以上空設定。

40、I/O Too Short 13 4. Message Display glossary 一覧 TASCAM DR-100 File Not Found PLAYLIST Battery Empty 以下一覧表示。 DR-100状況応表 示、内容知 、対処方法知表覧 。 The DIVIDE function would cause the file name to exceed 200 characters. The DIVIDE function adds _a or _b to the end of the file name. Before choosing the DIVIDE fu

41、nction, connect the unit to a computer and edit the file name to less than 198 characters. DIVIDE名文字数200文字超。DIVIDE行名末尾 _a_b追加。DIVIDE行前接続、198文字以下 名変更。 File Name ERR The DIVIDE function would cause the file name to be the same as that of an existing file. The DIVIDE function adds _a or _b to the end o

42、f the file name. Before choosing the DIVIDE func- tion, connect the unit to a computer and edit the file name. DIVIDE作成同名同内既存在 。DIVIDE行名末尾_a_b追加。DIVIDE行前 接続、名変更。 The file added to the playlist cannot be found or a file could be damaged. Please check the file in question. 登録見、壊可能性 。対象確認。 The audio fi

43、le is not a supported format. Check the file format (using puter). 形式対象外。 対象音楽形式対象外場合表示。対象形式確 認。 The battery is almost out of power. Recharge the lithium-ion battery and/or replace the AA batteries. 電池残量。専用充電池使用場合充電、単3形電池使用 場合電池交換。 The file in the Playlist cannot be found. Please confirm that the fi

44、le is still in the Music Folder. 登録見。MUSIC内対象 確認。 No files have been added to the Playlist. Add a file to the Playlist or change the play mode to something besides PLAYLIST. 登録。登録、 PLAYLIST以外設定。 The playlist is full. You cannot add more than 99 tracks to the Playlist. 一杯。最大99登録可能。 Dup File Name File

45、 not found Non-Supported No PLAYLIST PLAYLIST FULL Messages()Meaning and response(内容対処方法) The following is a list of the popup messages that might appear on the DR-100 under certain condi- tions. Refer to this list if one of these popup messages appears and you want to check the meaning or determine

46、 a proper response. The file is larger than the designated size or the recording time exceeds 24 hours. 指定超。録音時間24時間超。 Max File Size The position selected for divide is not suitable (too close to the beginning or end of a track). Divide実行時分割位置適切。 （曲先頭、曲最後） Cant Divide Folders can be created down to

47、two layers. You cannot create a new folder inside the current folder. 2階層。内新作成。 Layer too Deep 14 TASCAM DR-100 The card has no remaining capacity. Erase unnecessary files or move them to your computer to.make open space. 残容量。不要削除移動。 Card Full Write Timeout The system file required to operate this unit is invalid. When this message appears, press ENTER/MARK to automatically create a system file. 本機使用必要正常。表示 状態ENTER/MARK押新作。 Invalid SysFile Make Sys File Invalid Card Change Card This appears when the card is protected and lacks the necessary M