Yamaha-CDRS-1000-Service-Manual电路原理图.pdf

《Yamaha-CDRS-1000-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-CDRS-1000-Service-Manual电路原理图.pdf（48页珍藏版）》请在收音机爱好者资料库上搜索。

1、CDR-S1000 CDR-S1000 100701 SERVICE MANUAL CDR-S1000 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherant to the industry, and more specifically YAMAHA Products, are already kn

2、own and understood by the users, and have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components and failure of the product to perform as specified. For these reas

3、ons, we advise all YAMAHA product owners that all service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition

4、 of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMA

5、HA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive components. Discharge any

6、 static electricity your body may have accumu- lated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit. IC DATA . 1424 PIN CONN

7、ECTION DIAGRAM.25 PRINTED CIRCUIT BOARD . 2633 BLOCK DIAGRAM. 3435 SCHEMATIC DIAGRAM. 3639 REMOTE CONTROL TRANSMITTER .40 PARTS LIST. 4150 I CONTENTS TO SERVICE PERSONNEL . 12 REAR PANELS.3 SPECIFICATIONS.4 INTERNAL VIEW .5 DISASSEMBLY PROCEDURES . 57 SERVICE CHECK PROCEDURES . 89 TEST PROGRAM. 1013

8、 COMPACT DISC RECORDER RadioFans.CN 收音机爱 好者资料库 CDR-S1000 CDR-S1000 1 AC LEAKAGE TESTER OR EQUIVALENT EQUIPMENT UNDER TEST INSULATING TABLE WALL OUTLET WARNING: Laser Safety This product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause

9、eye damage. To protect your eyes and skin from laser radiation, the following precautions must be used during servicing of the unit. 1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away from the laser pick-up unit at all times. Do not stare

10、the laser beam at any time. 2) Do not attempt readjustment, disassemble or repair of the laser pick-up, unless noted elsewhere in this manual. 3) CAUTION : Use of controls, adjustments or preformance of procedures other than those specified herein may result in hazardous radiation exposure. 1. Criti

11、cal Components Information Components having special characteristics are marked Z and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all expo

12、sed conductive surfaces are properly insulated from supply circuits. GMeter impedance should be equivalent to 1500 ohm shunted by 0.15F. GLeakage current must not exceed 0.5mA. I TO SERVICE PERSONNEL WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. I

13、n addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/E

14、LECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of

15、 this product, wash your hands before handling food. GBe sure to test for leakage with the AC plug in both polarities. Laser Emitting conditions: 1) When the Top Cover is removed, and POWER SW is turned to the ON position, the laser component will emit a beam for several seconds to detect if a disc

16、is present. During this time (5-10 sec.) the laser may radiate through the lens of the laser pick-up unit. Do not attempt any servicing during this period ! If no disc is detected, the laser will stop emitting the beam. When a disc is set, you will not be exposed to any laser emissions. 2) The laser

17、 power level can be adjusted with VR on pick-up PWB, however, this level has been set by the factory prior to shipping from the factory. Do not adjust this laser level control unless instruuction is provided elsewhere in this manual. Adjustment of this control can increase the laser emission level f

18、rom the device. RadioFans.CN 收音机爱 好者资料库 CDR-S1000 CDR-S1000 2 Laser Diode Properties Material: GaAlAs Wavelength: 783 789 nm Emission duration: Continuous Laser output: Max. 44.6W* ANSI Class: Class 1 * This output is the value measured at a distance of about 200 mm from the objective lens surface o

19、n the Optical Pick- up Block. A, B, G models B, G models VARO!: AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NKYMTTMLLE LASER-STEILYLLE. L KATSO STEESEEN. VARNING! : OSYNLIG LASERSTRLNING NR DENNA DEL R PPNAD OCH SPRREN R URKOPPLAD. BETRAKTA EJ STRLEN. Variable resistor (Do not turn) Optica

20、l pick-up CDR-S1000 CDR-S1000 I REAR PANELS 3 M U, C models M A model M B, G models CDR-S1000 CDR-S1000 G DIMENSION Unit : mm (inch) I SPECIFICATIONS GENERAL ModelCompact disc recorder Application discsCDs, CD-Rs for AUDIO, CD-RWs for AUDIO Power Requirements U, C models120V AC 60Hz B, G models230V

21、AC 50Hz A model240V AC 50Hz Power Consumption35W Dimensions (W x H x D)435 x 108 x 400mm (17-1/8 x 4-1/4 x 15-3/4) Weight6.3kg (13 lbs 14 oz) Operating Temperature Range+5C to +35C Panel ColorBlack AUDIO PERFORMANCE Output Level 1kHz, 0dB2.0 0.5Vrms Frequency Response (EIAJ) 5Hz 20kHz0.5dB Signal to

22、 Nosie Ratio (EIAJ) Playback107dB Recording90dB Dynamic Range (EIAJ) Playback100dB Recording94dB Total Harmonic Distortion (1kHz) Playback0.004% Recording0.008% 435 (17-1/8) 17 (11/16) 91 (39/16) 108 (41/4) 12 (1/2) 7 (1/4) 381 (15) 400 (153/4) 4 *Specifications are subject to change without notice.

23、 U .U. S. A. model C .Canadian model A . Australian model B . British model G . European model INPUT/OUTPUT Line Output Output Level2.0 Vrms Output Impedance990 Line Input Input Sensitivity500m Vrms Input Impedance24k (REC LEVEL Max.) Digital Output Coaxial Output Level0.5Vp-p (75) Optical Output Le

24、vel-20 dBm Sampling Frequency44.1kHz Digital Input Coaxial Input Level0.5Vp-p (75) Optical Input Level-20 dBm Input Gain12dB, with Digital Volume 0dB, without Digital Volume Sampling Frequency Tolerance32kHz to 48kHz, with SRC 44.1kHz 100ppm, without SRC (CD DIRECT mode) Headphone Output Output Leve

25、l300m Vrms (-20dB, 150 load) (PHONES LEVEL Max.) CDR-S1000 CDR-S1000 I INTERNAL VIEW I DISASSEMBLY PROCEDURES (Remove parts in disassembly order as numbered.) t!1 qw yiuo!0 re qANALOG P.C.B. (3) wMAIN P.C.B. (1) eCDR MECHANISM UNIT rANALOG P.C.B. (1) tPANEL P.C.B. (5) yANALOG P.C.B. (2) uPANEL P.C.B

26、. (1) iMAIN P.C.B. (2) oPANEL P.C.B. (2) !0PANEL P.C.B. (3) !1PANEL P.C.B. (4) CDR MECHANICAL UNIT REPLACEMENT When sending back the defective CDR mechanical unit for repair, send the whole unit. The CDR mechanical unit must be replaced as a unit. None of its components can be supplied separately. W

27、hen sending back the defective CDR mechanical unit for repair, attach the disc which was used when the error occurred as necessary. However, Yamaha shall not be liable even if the data in the disc has become unreadable while the unit is being serviced/repaired. Preparation before Replacement a. When

28、 replacing the CDR mechanical unit, write down the following items. Serial No. of the product and the symptom in detail Mechanical serial No. / mechanical shipping serial No. of CDR mechanical unit b. Prepare a lens cover (P/No. V4870500) to use when transporting the CDR mechanical unit. Mechanical

29、serial No.Shipping serial No. Lens cover 5 CDR-S1000 CDR-S1000 6 Fig. 3 Fig. 1 r e q q CDR Mechanical Unit w t t 1. CDR Mechanical Unit Removal a. Turn off the power and disconnect the power plug from the service outlet. CAUTION : Never disconnect any cable, remove any screw or other part while the

30、power switch is on. b. Remove 4 screws marked q and 1 screw marked w, and the Top Cover can be removed. (Fig. 1) c. Disconnect the power cable / IDE cable / word clock cable from the CDR mechanical unit. (Fig. 2) d. Remove 2 hexagonal cap nuts marked e. (Fig. 1) e. Remove 4 screws marked r, and take

31、 out the CDR mechanical unit. (Fig. 1) f. Remove the Lid. g. Remove 4 screws marked t, and the Frame/CDR can be removed. (Fig. 3) Top Cover Word Clock Cable r IDE Cable Power Cable CDR Mechanical Unit CDR Mechanical Unit Lid Fig. 2 Frame/CDR 2. Transportation of CDR Mechanical Unit a. When transport

32、ing the CDR mechanical unit, be sure to install the lens cover to it and put it in the anti-static bag before packaging it. IDE cable a. Do not remove the cable from the female connector by pulling on the cable. b. Remove the connector from the female connector by in- serting the minus driver into t

33、he insertion place and hook- ing the female connector as per fig. A. Fig. A A insertion place CDR-S1000 CDR-S1000 7 3. CDR Mechanical Unit Installation a. Before installing the CDR mechanical unit, check that the jumper pin on its rear panel is inserted in the MAS- TER jack. b. Install the component

34、s of the CDR mechanical unit cor- rectly in the reverse order of the removal. c. Use special care for the power cable of the CDR me- chanical unit. If it is connected in reverse, the mechani- cal unit will be damaged and fail to operate. The end of the power cable with a red line is the No.1 pin sid

35、e (+12V). Connect it to No.1 pin of the DC power input connector. d. The No.1 pin side of the IDE cable of the CDR mechani- cal unit can be identified by a red line. Connect it to No.1 pin of the IDE interface connector. 4. Operation Check after Installation 1) Checking after turning on the power Wh

36、en the power is supplied, the CDR mechanical unit executes self-diagnosis automatically. If an error is detected in the initial self-diagnosis, LED segments (LED601: ON/DISC, LED602: Read/Write) on the front panel of the mechanical unit light up (in or- ange) simultaneously and remain on. If a malfu

37、nction has occurred, power on fails. (IDE com- mand error) 2) Checking when malfunction has occurred a. Check each cable for correct connection. b. Check the power supply voltages. (Measure voltage at the power connector of the mechanical unit.) c. Check to ensure that the jumper pin on the rear pan

38、el is inserted in the MASTER jack. CDR mechanical unit Usually called CDR/RW drive unit Model name : ACRW100A MASTER Rear view (ACRW100A) Front view (ACRW100A) Tray Manual Eject Lever LEDEject Switch DC Input IDE Interface Connector Jumper Pin Analog Audio Out Word Clock Out Frame Ground WC GND Pin

39、40 Pin 1 Pin 2qr CDR-S1000 CDR-S1000 8 I SERVICE CHECK PROCEDURES When the main unit fails to operate. 1. Check the power supply voltage of ANALOG P.C.B. (2). Connector W100 W201 CB601 Pin No. 1pin (+5V) 4pin (VP) 5pin (FL1) 6pin (FL2) 1pin (-VA) 3pin (+VA) 1pin (+12V) 4pin (+5V) Specified voltage 5

40、.0 0.25V -27.0 1.5V 4.4 0.4Vrms 4.4 0.4Vrms -9.5 0.8V 7.3 0.6V 12.0 0.6V 5.0 0.25V Remarks +5V power supply (Main P.C.B.) -27V power supply (FL display) +4V(AC) power supply (FL display) +4V(AC) power supply (FL display) -VA power supply (Analog P.C.B.) +VA power supply (Analog P.C.B.) +12V power su

41、pply (CDR drive) +5V power supply (CDR drive) 2. Turn off the power to check the condition of the CDR drive section. 3. Disconnect the IDE cable. 4. Turn on the power and check the CDR drive section for proper operation. (Check the condition of the CDR drive.) The CDR drive should operate by itself.

42、 (Focusing, disc motor revolution) Operation failure means defective CDR drive. 5. Turn on the power again and check the CPU and FL display for proper operation. Does the FL display light up after a few seconds? Is the FL driver accessed? (FL DATA, FL SCK, FL N CS) 6. Turn off the power and connect

43、the IDE cable. 7. Start the TEST program and check the condition of the main P.C.B.(by using the self- diagnosis function). When skipping occurs from time to time, playback/recording is disabled. 1. Using a standard disc (TDK CD-RXA74 or TDK CD-RWXA74), check if recording and playback are executable

44、. CAUTION: How to handle discs Handle the disc with special care not to scratch it or make it dirty. Also do not expose it to ultra-violet rays when keeping it in storage. (Greater care should be used than when handling a CD disc.) CD-RW74 can be used repeatedly but use a number of 20 times as a rou

45、gh standard for the limit. If the CD-R is a self-record/playback type, it can be reused (for additional recording) unless it is finalized. (Nothing can be recorded additionally if finalized.) The CD-R disc which has not been finalized cannot be played back on a general type CD player. To play back t

46、he CD-RW, an applicable type CD player must be used. CDR-S1000 CDR-S1000 9 Check the power supply NG OK Turn off the power to the drive section to check its condition. Disconnect the IDE cable. Turn on the power and check the operation. NO YES If the drive starts operating by itself, focusing functi

47、ons properly and the disc motor runs, the drive section is in good condition. Check the condition of the main P.C.B. Both main P.C.B and CPU are in good condition. After some time Does the display light up? YES YES Driver IC, FL display failure NO NO *1: FL_DATA, FL_SCK, FL_N_CS Is the FL driver accessed? *1 CPU or connection may be defective. Check the fault in the power supply section. If operation fails, the drive section is defective. SERVICE CHECK FLOW CHART CDR-S1000 CDR-S1000 10 CB7 D3 I TEST PR